Mitsubishi Outlander GS45X. Manual — part 1724
DIAGNOSIS <S-AWC(SUPER ALL WHEEL CONTROL)>
TSB Revision
AUTOMATIC TRANSAXLE
23C-201
STEP 8. Check of the electronic control coupling solenoid
(center)
Refer to GROUP 27C
− On-vehicle Service
Q: Is the check result normal?
YES : Go to Step 9.
NO : Replace the electronic control coupling (center)
(Refer to GROUP 27C
− Electronic Control Coupling
). Then go to Step 10.
STEP 9. Check whether the diagnostic trouble code is
reset.
Q: Is diagnostic trouble code No.C1626 set?
YES : Replace the AWC-ECU. (Refer to
go to Step 10.
NO : Intermittent malfunction. (Refer to GROUP 00
− How
to Cope with Intermittent Malfunction
).
STEP 10. Check whether the diagnostic trouble code is
reset.
Q: Is diagnostic trouble code No.C1626 set?
YES : Return to Step 1.
NO : This diagnosis is complete.
DIAGNOSIS <S-AWC(SUPER ALL WHEEL CONTROL)>
TSB Revision
AUTOMATIC TRANSAXLE
23C-202
Code No. C1627: Abnormal Electronic Control Solenoid (Front) Current
.
AWC-ECU
Electronic control coupling solenoid (front) system circuit
AC902489
ELECTRONIC
CONTROL
COUPLING
SOLENOID
(FRONT)
AC901112
Connector: A-13
AH
AC901598
AD
Connector: B-28
B-28 (GR)
AC901075BM
Connector: C-42
AC901075BN
Connector: C-139
DIAGNOSIS <S-AWC(SUPER ALL WHEEL CONTROL)>
TSB Revision
AUTOMATIC TRANSAXLE
23C-203
OPERATION
The AWC-ECU monitors the current value of the
electronic control coupling solenoid (Front).
.
DIAGNOSTIC TROUBLE CODE SET
CONDITIONS
This diagnostic trouble code is set when the abnor-
mality below is detected:
• By the monitored electronic control solenoid
(front) current, the AWC-ECU judges the under-
current failure.
• By the monitored electronic control solenoid
(front) current, the AWC-ECU judges the overcur-
rent failure.
• The AWC-ECU judges the monitor circuit failure.
.
PROBABLE CAUSES
• Malfunction of electronic control coupling sole-
noid (Front)
• Damaged harness wires and connectors
• Malfunction of AWC-ECU
DIAGNOSTIC PROCEDURE
STEP 1. Electronic control coupling solenoid (front)
connector, intermediate connector, AWC-ECU connector
check: B-28, A-13, C-42, C-139
Q: Is the check result normal?
YES : Go to Step 2.
NO : Repair the defective connector. Then go to Step 6.
STEP 2. Check the wiring harness between B-28 electronic
control coupling solenoid (front) connector terminal No.1
and C-139 AWC-ECU connector terminal No.1.
Check the power supply line for open or short circuit.
Q: Is the check result normal?
YES : Go to Step 3.
NO : Repair the wiring harness. Then go to Step 6.
STEP 3. Check the wiring harness between B-28 electronic
control coupling solenoid (front) connector terminal No.2
and C-139 AWC-ECU connector terminal No.14.
Check the ground line for open or short circuit.
Q: Is the check result normal?
YES : Go to Step 4.
NO : Repair the wiring harness. Then go to Step 6.
STEP 4. Check of the electronic control coupling solenoid
(Front)
Refer to
.
Q: Is the check result normal?
YES : Go to Step 5.
NO : Replace the transfer assembly (Refer to
).
Then go to Step 6.
DIAGNOSIS <S-AWC(SUPER ALL WHEEL CONTROL)>
TSB Revision
AUTOMATIC TRANSAXLE
23C-204
STEP 5. Check whether the diagnostic trouble code is
reset.
Q: Is diagnostic trouble code No.C1627 set?
YES : Replace the AWC-ECU. (Refer to
go to Step 6.
NO : Intermittent malfunction. (Refer to GROUP 00
− How
to Cope with Intermittent Malfunction
).
STEP 6. Check whether the diagnostic trouble code is
reset.
Q: Is diagnostic trouble code No.C1627 set?
YES : Return to Step 1.
NO : This diagnosis is complete.
Code No. C1628: Abnormal Electronic Control Solenoid (center) Current
AWC-ECU
Electronic control coupling solenoid (rear) system circuit
AC902490
ELECTRONIC
CONTROL
COUPLING
SOLENOID
(CENTER)
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст