Mitsubishi Outlander GS45X. Manual — part 62
REAR COMBINATION LIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-245
STEP 2. Using scan tool MB991958, read the diagnostic
trouble code.
CAUTION
To prevent damage to scan tool MB991958, always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting scan tool MB991958.
(1) Connect scan tool MB991958. Refer to "How to connect
scan too (M.U.T.-III)
."
(2) Turn the ignition switch to the "ON" position.
(3) Check whether the ETACS-ECU related DTC is set.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the DTC set?
YES : Diagnose the ETACS-ECU. Refer to
.
NO : Go to Step 3.
STEP 3. Using scan tool MB991958, check data list.
Use the ETACS-ECU data list to check the signals related to
the taillight illumination.
• Turn the ignition switch to the "ACC" position.
• Turn the taillight switch to the "ON" position.
Q: Does scan tool MB991958 display the items "Taillight"
as normal condition?
YES <Normal condition is displayed for item.> : Go to
Step 4.
NO <Normal condition is not displayed for item No.
218.> : Troubleshoot the ETACS-ECU. Refer to Inspection
Procedure 12 "ETACS-ECU does not receive any
signal from the column switch signal"
.
ZC501967
AC404789
AC702802
MB991824
MB991827
MB991910
Data link
connector
AB
Item No.
Item name
Normal
conditions
Item 218
Taillight
ON
REAR COMBINATION LIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-246
STEP 4. Retest the system
Check that the taillight illuminates normally.
Q: Does the taillight work normally?
YES : The trouble can be an intermittent malfunction (Refer
to GROUP 00
− How to use
Troubleshooting/inspection Service Points
− How to
Cope with Intermittent Malfunction
NO : Replace the ETACS-ECU.
Inspection Procedure 2: One of the taillights does not illuminate.
.
Taillight Circuit
REAR
COMBINATION
LIGHT
(TAIL
:LH)
(TAIL
:RH)
ETACS-ECU
TAILLIGHT CONTROL CIRCUIT
ACA02655 AC
Connector: C-311
AC709496
AD
Connectors: D-09, D-14
D-14
D-09
REAR COMBINATION LIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-247
TECHNICAL DESCRIPTION (COMMENT)
When one of the taillights does not illuminate, the
wiring harness, connector(s), or rear combination
light unit may have a problem, or the fuse may be
burned out.
.
TROUBLESHOOTING HINTS
• Malfunction of rear combination light unit
• The wiring harness or connectors may have
loose, corroded, or damaged terminals, or termi-
nals pushed back in the connector
DIAGNOSIS
Required Special Tools:
• MB992006: Extra fine probe
• MB991223: Harness set
• MB991958: Scan Tool (M.U.T.-III Sub Assembly)
• MB991824: Vehicle Communication Interface (V.C.I.)
• MB991827: M.U.T.-III USB Cable
• MB991910: M.U.T.-III Main Harness A (Vehicles with
CAN communication system)
STEP 1. Check rear combination light connectors D-09
(RH) and D-14 (LH) for loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Q: Is rear combination light connectors D-09 (RH) and D-14
(LH) in good condition?
YES : Go to Step 2.
NO : Repair the damaged parts
STEP 2. Resistance measurement at rear combination light
connectors D-09 (RH) and D-14 (LH).
(1) Disconnect the connector, and measure at the wiring
harness side.
(2) Measure the resistance between the connector of light
which does not illuminate and body ground.
•
Measure the resistance between rear combination light
connector D-09 (RH) (terminal No. 4) and body ground.
•
Measure the resistance between rear combination light
connector D-14 (LH) ( terminal No. 4) and body ground.
The measured value should be continuity exists (2
Ω or less).
Q: Does the measured resistance value correspond with
this range?
YES : Go to Step 4.
NO : Go to Step 3.
AC702818
Connector D-09
(Harness side)
AP
AC702818
Connector D-14
(Harness side)
AQ
REAR COMBINATION LIGHT
TSB Revision
CHASSIS ELECTRICAL
54A-248
STEP 3. Check the wiring harness between rear
combination light connectors D-09 (RH) and D-14 (LH)
(terminal No. 4) and ground.
Check the ground line for open circuit.
Q: Is the check result normal?
YES : Go to Step 4.
NO : Repair the wiring harness.
STEP 4. Check ETACS-ECU connectors C-311 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is ETACS-ECU connectors C-311 in good condition?
YES : Go to Step 5.
NO : Repair the damaged parts.
STEP 5. Check the wiring harness between rear
combination light connector D-09 (RH), D-14 (LH) and
ETACS-ECU connector C-311 (terminal No. 13) (RH),
(terminal No. 10) (LH).
Check the communication line for open or short circuit.
Q: Is the wiring harness between rear combination light
connector D-09 (RH), D-14 (LH) and ETACS-ECU
connector C-311 (terminal No. 13) (RH), (terminal No. 10)
(LH) in good condition?
YES : Go to Step 6.
NO : Repair the wiring harness.
STEP 6. Retest the system.
Check that the taillight illuminates normally.
Q: Does the taillight work normally?
YES : The trouble can be an intermittent malfunction (Refer
to GROUP 00
− How to use
Troubleshooting/inspection Service Points
− How to
Cope with Intermittent Malfunction
NO : Replace the rear combination light unit.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст