Mitsubishi Outlander GS45X. Manual — part 140
MMCS
TSB Revision
CHASSIS ELECTRICAL
54A-557
C-10
.
C-39
Terminal
No.
Signal symbol
Check condition
Terminal voltage
2
SPEAKER RL (
−)
When the sound is output
0 - Battery positive voltage
(AC)
3
SPEAKER FL (
−)
When the sound is output
0 - Battery positive voltage
(AC)
6
AMP DATA
Ignition switch: ON
Battery positive voltage
(DC)
7
SPEAKER FR (
−)
When the sound is output
0 - Battery positive voltage
(AC)
8
SPEAKER RR (
−)
When the sound is output
0 - Battery positive voltage
(AC)
9
MAIN GND
Always
1 volt or less
10
ILLUMINATION (+)
Taillight switch: ON
Battery positive voltage
(DC)
11
SPEAKER RL (+)
When the sound is output
0 - Battery positive voltage
(AC)
12
SPEAKER FL (+)
When the sound is output
0 - Battery positive voltage
(AC)
13
VSS
Ignition switch: ON
0 - Battery positive voltage
(pulse)
14
ACCESSORY (+)
Ignition switch: ACC position
Battery positive voltage
(DC)
15
SPEAKER FR (+)
When the sound is output
0 - Battery positive voltage
(AC)
16
SPEAKER RR (+)
When the sound is output
0 - Battery positive voltage
(AC)
17
BATTERY (+)
Always
Battery positive voltage
(DC)
Terminal
No.
Signal symbol
Check condition
Terminal voltage
91
VCC (RC 6.5v)
Selector lever : R position
Ignition switch: ON position
5.8
− 7.0V (DC)
92
GND
Always
1 volt or less
93
CAMERA SIGNAL
Selector lever : R position
Ignition switch: ON position
1Vp-p (AC)
95
SEIELD (CAMERA)
Always
1 volt or less
96
CAMERA DETECT
Selector lever: R position
Ignition switch: ON position
0 - 5V (DC)
MMCS
TSB Revision
CHASSIS ELECTRICAL
54A-558
CAN BOX UNIT
.
C-13
AC611333
C-13
AK
Terminal
No.
Signal symbol
Check condition
Terminal voltage
1
GND
Always
1 volt or less
2
BATTERY (+)
Always
Battery positive voltage
(DC)
4
TX (AND)
Ignition switch: ACC position
5V (DC)
5
RX (AND)
Ignition switch: ACC position
2 - Battery positive
voltage (DC)
6
CAN-BOX DATA CLK
Ignition switch: ACC position
1 - 5V (pulse)
8
CAN-H
−
−
9
CAN-L
−
−
10
ACCESSORY (+)
Ignition switch: ACC position
Battery positive voltage
(DC)
MMCS
TSB Revision
CHASSIS ELECTRICAL
54A-559
REMOVAL AND INSTALLATION
M1546001000790
AC511339
AC703775AD
1
1
2
4
6
5
3
7
9
10
A
A
B
B
C
C
Section A – A
Section B – B
Section C – C
6
Clip
Clip positions
NOTE:
2
Clip
1
Clip
3.0 ± 1.0 N·m
27 ± 8 in-lb
1.5 ± 0.5 N·m
14 ± 4 in-lb
1.5 ± 0.5 N·m
14 ± 4 in-lb
3.0 ± 1.0 N·m
27 ± 8 in-lb
1.5 ± 0.5 N·m
14 ± 4 in-lb
3.0 ± 1.0 N·m
27 ± 8 in-lb
8
AC900455
11
Section A – A
Claw
Claw
11
A
A
Rear floor console
AM
NOTE
:Claw positions
Multivision Display Removal
Steps
1.
Center outlet
2.
Center panel assembly
3.
Multivision display
4.
Multivision display bracket
5.
CAN box unit
6.
CAN box unit bracket
7.
Navigation harness
8.
TMC cable
GPS Antenna Removal Steps
1.
Center outlet
2.
Center panel assembly
Multivision Display Removal
Steps (Continued)
MMCS
TSB Revision
CHASSIS ELECTRICAL
54A-560
INSPECTION
AUDIO AND VIDEO ADAPTER CHECK
M1546023200048
1. Remove the audio and video adapter.(Refer to
.)
2. Check that continuity exists between the terminal and the
pin jack of audio and video adapter.
9.
Center upper box
10. GPS antenna
Audio And Video Adaptor
Removal Steps
•
Rear floor console assembly (Refer
to GROUP 52A
− Rear Floor
Console Assembly
11. Audio and video adaptor
GPS Antenna Removal Steps
The connecting position
of pin jack side circuit
tester
Terminal
number
Measurem
ent value
1
2
Continuity
exists. (2
Ω
or less)
2
1
3
5
4
4
5
5
6
6
AC707484
AUDIO
L (MONO)
AUDIO
R
VIDEO
IN
red
white
yellow
1
2
3
4
5
Pin jack
AB
6
Pin jack
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст