Mitsubishi Outlander GS45X. Manual — part 1738
DIAGNOSIS <S-AWC(SUPER ALL WHEEL CONTROL)>
TSB Revision
AUTOMATIC TRANSAXLE
23C-257
TEST
1. The test can be performed only when all the
following conditions are satisfied.
• Every wheel speed sensor input is 20 km/h (12
mph) or less.
• No system malfunction is detected.
• The steering angle of steering wheel is within
±30° from the neutral position.
2. With the test, when any of the conditions below is
met, the forced activation will be cancelled.
• Any of the wheel speed sensors detects an input
of 20 km/h (12 mph) or more (excluding item No.
4 "Control OFF").
• A system malfunction is detected.
• The forced activation time has elapsed.
• M.U.T.-III is removed.
• M.U.T.-III clear key is operated.
Item
No.
Display on M.U.T.-III
Test content
Normal conditions
4
Control OFF
The electronic control coupling
(front/center) operation stops
Refer to the electronic control coupling
(front/center) operation check.
5
Front coupling operation
check
The electronic control coupling
(Front) maximum restraint
Refer to the electronic control coupling
(Front) operation check.
6
center coupling
operation check
The electronic control coupling
(center) maximum restraint
The electronic control coupling (center)
operation check.
DIAGNOSIS <S-AWC(SUPER ALL WHEEL CONTROL)>
TSB Revision
AUTOMATIC TRANSAXLE
23C-258
CHECK AT AWC-ECU TERMINAL
M1235004800013
AC506684
22
9
16
15
2
14
1
3
19
6
18
17
4 5
20
7
21
8
25
12
23
10
24
11
26
13
JAE-E
39
50
44
4243
32
31
33
JAE-E
47
36
45 46
34 35
49
48
3738
52
51
40 41
C-139
AN
Ter
mina
l No.
Inspection Items
Inspection requirement
Normal Condition
1
Electronic control
coupling solenoid
(front)
Using M.U.T.-III, perform "Test Item No. 4: Control
OFF" of "SPECIAL FUNCTION"
1 V or less
Using M.U.T.-III, perform "Test Item No. 5: Front
coupling operation check" of "SPECIAL FUNCTION"
Approximately 8 V
2
Electronic control
coupling solenoid
(center)
Using M.U.T.-III, perform "Test Item No. 4: Control
OFF" of "SPECIAL FUNCTION"
1 V or less
Using M.U.T.-III, perform "Test Item No. 6: center
coupling operation check" of "SPECIAL FUNCTION"
Approximately 8 V
3
Electronic control
coupling solenoid
(center)
Always
1 V or less
6
S-AWC control mode
selector signal1
Ignition switch: ON
S-AWC control mode
selector: SNOW or OFF
ROAD
Battery positive
voltage
S-AWC control mode
selector: NORMAL
1 V or less
7
S-AWC control mode
selector signal2
Ignition switch: ON
S-AWC control mode
selector: SNOW or
NORMAL
Battery positive
voltage
S-AWC control mode
selector: OFF ROAD
1 V or less
12
Power supply
Always
Battery positive
voltage
13
Ground
Always
1 V or less
14
Electronic control
coupling solenoid
(front)
Always
1 V or less
16
Ignition switch
Ignition switch: ON
Battery positive
voltage
Ignition switch: OFF
1 V or less
17
Back up power supply
Always
Battery positive
voltage
23
CAN-H
−
−
24
CAN-L
−
−
SPECIAL TOOLS
TSB Revision
AUTOMATIC TRANSAXLE
23C-259
SPECIAL TOOLS
M1231000601115
Tool
Tool number and name Supersession
Application
MD998330 (Includes
MD998331)
Oil pressure gauge (3.0
MPa, 427 psi)
MD998330-01
Measurement of hydraulic pressure
MB991958
a. MB991824
b. MB991827
c. MB991910
d. MB991911
e. MB991914
f. MB991825
g. MB991826
M.U.T.-III sub assembly
a. Vehicle
communication
interface (V.C.I.)
b. M.U.T.-III USB cable
c. M.U.T.-III main
harness A (Vehicles
with CAN
communication
system)
d. M.U.T.-III main
harness B (Vehicles
without CAN
communication
system)
e. M.U.T.-III main
harness C (for
Chrysler models only)
f. M.U.T.-III
measurement adapter
g. M.U.T.-III trigger
harness
MB991824-KIT
NOTE: g:
MB991826
M.U.T.-III Trigger
Harness is not
necessary when
pushing V.C.I.
ENTER key.
CAUTION
M.U.T.-III main harness A
(MB991910) should be used.
M.U.T.-III main harness B and C
should not be used for this
vehicle.
A/T system check (Diagnostic
trouble code, service data)
MB992127
Adapter
-
Connection for oil pressure gauge
AC103525
MB991910
MB991826
MB991958
MB991911
MB991914
MB991824
MB991827
MB991825
Do not use
a
b
c
d
e
f
g
Do not use
SPECIAL TOOLS
TSB Revision
AUTOMATIC TRANSAXLE
23C-260
MB995062
Flushing tool
MLR-6906B or
Equivalent
Flushing cooler and tube
MB992208
Engine hanger plate A
General Service
Tool
Supporting the engine assembly
during removal and installation of
the transaxle assembly
MB991454
Engine hanger balancer
MZ203827-01
When the engine hanger is used:
Supporting the engine assembly
during removal and installation of
the transaxle assembly
NOTE: Special tool MB991454 is a
part of engine hanger attachment
set MB991453.
MB991527
Hanger
Tool not available
MB991895
Engine hanger
Tool not available
MB991928
Engine hanger
a: MB991929
Joint (50) x 2
b: MB991930
Joint (90) x 2
c: MB991931
Joint (140) x 2
d: MB991932
Foot (standard) x 4
e: MB991933
Foot (short) x 2
f: MB991934
Chain and fork
assembly
Tool not available
Tool
Tool number and name Supersession
Application
MB992208
B991454
B991527
MB991895
B991928
a
b
c
d
e
f
Slide bracket (HI)
AI
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст