Mitsubishi Outlander GS45X. Manual — part 1607

EMISSION CONTROL <MFI>

TSB Revision

ENGINE AND EMISSION CONTROL

17-77

PURGE CONTROL SYSTEM CHECK

(PURGE FLOW CHECK)

M1173001401593

Required Special Tool:
MB995061: Purge Flow Indicator
1. Disconnect the purge hose from the evaporative emission

(EVAP) purge solenoid, and connect special tool MB995061
between the EVAP purge solenoid and the purge hose.

2. Before inspection, set the vehicle in the following conditions:

• Engine coolant temperature: 80 − 95°C (176 − 203°F)

• Lights, electric cooling fan and accessories: OFF

• Transaxle: P range

NOTE: Vehicles for Canada, the headlight, taillight, etc.
remain lit even when the lighting switch is in "OFF" position
but this is no problem for checks.

AK700061

AB

Spare tire

Evaporative emission ventilation solenoid

AK604168 AB

Intake manifold

Throttle body

From
aircleaner

To
combustion
chamber

OFF

ON

Evaporative
emission
purge solenoid
(ON: Open)

Evaporative
emission
canister

Purge flow
indicator
(MB995061)

Purge hose

EMISSION CONTROL <MFI>

TSB Revision

ENGINE AND EMISSION CONTROL

17-78

3. Run the engine at idle for more than four minutes.
4. Check the purge flow volume when engine is revved

suddenly several times.

Standard value: Momentarily 20 cm

3

/s (2.5 SCFH) or

more.

5. If the purge flow volume is less than the standard value,

check it again with the vacuum hose disconnected from the
EVAP canister. If the purge flow volume is less than the
standard value, check the vacuum port and the vacuum
hose for clogging. Also check the EVAP purge solenoid. If
the purge flow volume is at the standard value, replace the
EVAP canister.

EVAPORATIVE EMISSION PURGE SOLENOID
CHECK

M1173001701044

1. Disconnect the vacuum hose from the evaporative emission

(EVAP) purge solenoid.

2. Disconnect the harness connector.
3. Connect a hand vacuum pump to nipple (A) of the EVAP

purge solenoid (refer to the illustration at left).

4. As described in the chart below, check airtightness by

applying a vacuum with voltage applied directly from the
battery to the EVAP purge solenoid valve and without
applying voltage.

5. Measure the resistance between the terminals of the EVAP

purge solenoid.

Standard value: 22

− 26 Ω [at 20°C (68°F)]

6. Replace the solenoid if resistance is out of specification.

BATTERY POSITIVE
VOLTAGE

NORMAL CONDITION

Applied

Vacuum leaks

Not applied

Vacuum maintained

AK402742AK

A

B

Battery

AK502148

EMISSION CONTROL <MFI>

TSB Revision

ENGINE AND EMISSION CONTROL

17-79

MASS AIRFLOW SENSOR CHECK

M1173050400224

.

<2.4L Engine>

To inspect these parts, refer to GROUP 13A, Multiport Fuel
Injection (MFI) <2.4L Engine>

− Multiport Fuel Injection (MFI)

Diagnosis

− Diagnostic Trouble Code Chart

P.13A-49

.

.

<3.0L Engine>

To inspect these parts, refer to GROUP 13B, Multiport Fuel
Injection (MFI) <3.0L Engine>

− Multiport Fuel Injection (MFI)

Diagnosis

− Diagnostic Trouble Code Chart

P.13B-50

.

BAROMETRIC PRESSURE SENSOR CHECK

M1173008000377

.

<2.4L Engine>

To inspect the sensor, refer to GROUP 13A, Multiport Fuel
Injection (MFI) <2.4L Engine>

− Multiport Fuel Injection (MFI)

Diagnosis

− Diagnostic Trouble Code Chart

P.13A-49

.

.

<3.0L Engine>

To inspect the sensor, refer to GROUP 13B, Multiport Fuel
Injection (MFI) <3.0L Engine>

− Multiport Fuel Injection (MFI)

Diagnosis

− Diagnostic Trouble Code Chart

P.13B-50

.

ENGINE COOLANT TEMPERATURE SENSOR
CHECK

M1173008100783

.

<2.4L Engine>

To inspect the sensor, refer to GROUP 13A, Multiport Fuel
Injection (MFI) <2.4L Engine>

− Multiport Fuel Injection (MFI)

Diagnosis

− Diagnostic Trouble Code Chart

P.13A-49

.

.

<3.0L Engine>

To inspect the sensor, refer to GROUP 13B, Multiport Fuel
Injection (MFI) <3.0L Engine>

− Multiport Fuel Injection (MFI)

Diagnosis

− Diagnostic Trouble Code Chart

P.13B-50

.

INTAKE AIR TEMPERATURE SENSOR CHECK

M1173008200423

.

<2.4L Engine>

To inspect the sensor, refer to GROUP 13A, Multiport Fuel
Injection (MFI) <2.4L Engine>

− Multiport Fuel Injection (MFI)

Diagnosis

− Diagnostic Trouble Code Chart

P.13A-49

.

.

<3.0L Engine>

To inspect the sensor, refer to GROUP 13B, Multiport Fuel
Injection (MFI) <3.0L Engine>

− Multiport Fuel Injection (MFI)

Diagnosis

− Diagnostic Trouble Code Chart

P.13B-50

.

EMISSION CONTROL <MFI>

TSB Revision

ENGINE AND EMISSION CONTROL

17-80

FUEL TANK DIFFERENTIAL PRESSURE SENSOR
CHECK

M1173007700317

To inspect the sensor, refer to GROUP 13C, Fuel Supply

− Fuel

Tank

− Fuel Tank Inspection − Fuel Tank Differential Pressure

Sensor Check

P.13C-27

.

EVAPORATIVE EMISSION VENTILATION
SOLENOID CHECK

M1173007800273

Refer to Emission Control

− Evaporative Emission Canister and

Fuel Tank Pressure Relief Valve

− Inspection − Evaporative

Emission Ventilation Solenoid Check

P.17-88

.

EXHAUST GAS RECIRCULATION (EGR) SYSTEM

GENERAL INFORMATION (EXHAUST GAS RECIRCULATION SYSTEM)

M1173005201085

The exhaust gas recirculation system (EGR) lowers
the nitrogen oxides (NOx) emission level. When the
air/fuel mixture combustion temperature is high, a
large quantity of NOx is generated in the combustion
chamber. Therefore, this system recirculates part of
exhaust gas from the exhaust port of the cylinder
head to the combustion chamber through the intake
manifold to decrease the air/fuel mixture combustion
temperature, resulting in reduction of NOx. The EGR
flow rate is controlled by the EGR valve (Stepper
Motor) for driveability quality.

OPERATION

When the engine coolant temperature is low, when
the engine is at idle or when a wide open throttle
operation is performed, the EGR valve (Stepper
Motor) is kept closed, achieving no EGR. After warm-
ing up the engine, the EGR valve (Stepper Motor)
can be opened by the engine control module (ECM).
The ECM monitors the EGR system and illuminates
the Malfunction Indicator Lamp (SERVICE ENGINE
SOON or Check Engine Lamp) to indicate that there
is a malfunction.

SYSTEM DIAGRAM
<2.4L Engine>

AK502987AE

ECM

Mass airflow sensor

Intake air temperature sensor

Manifold absolute

pressure sensor

Engine coolant

temperature sensor

Throttle position sensor

Crankshaft position sensor

Battery

EGR valve

(stepper motor)