Mitsubishi Eclipse. Technical Information Manual (1994) — part 75
Unlock switch
Lock switch
O N
Signals
transmitted
Unlock signal
Lock signal
Signals
received
by
receiver
Door unlock signal
O N
light (operation confirmation function).
NOTE
The receiver determines that the codes are in agree-
I
O F F
I
the transmitter coincides with the code stored in the
ment when any of the three codes transmitted from
I
receiver.
Door lock signal
O N
O F F
Door lock
switch
O N
(Unlock)
O F F
(Lock)
Dome light
O N
O F F
0.5 sec. 0.5 sec.
3 sec.
BODY
Entry System
OPERATION IN SYSTEM OPERATION MODE
When the transmission switch is pressed once, three
identical codes are transmitted from the transmitter.’
The secret code is decrypted by the comparator circuit
in the receiver which compares the code with the
code stored in the receiver. When the transmitted
code coincides with the stored code, the receiver
sends a door unlock signal or door lock signal to
the ETACS-ECU.
In response to the signal, the doors are locked or
unlocked. When the door lock switch in the door lock
actuator is caused to be ON (unlock) or OFF (lock),
the receiver causes the dome light to flash or steadily
Signals
received
by receiver
Unlock signal
r - l
Door unlock signal
Door lock signal
O N
I
O F F
I
Door switch
30 sec.
O N
O F F
Door lock switch
O N
I
I
(Lock)
TIMER LOCK FUNCTION
If none of the doors is opened in less than 30 seconds
after the doors have been unlocked by the
entry system, the receiver will automatically output
a door lock signal to the ETACS-ECU to re-lock the
doors.
This function prevents accidental unlocking of the
doors that may be caused by an unintentional opera-
tion of the transmitter.
Operation Inhibit Conditions
In the following cases, operation of the system is
inhibited.
l
When a code different from the one stored in
the receiver is received 30 consecutive times
in a minute, operation of the system is inhibited
for 10 minutes.
l
When the ignition key is in the ignition switch
(detected by the key reminder switch)
l
When any of the doors is not fully closed (door
switch: ON)
Code registration switch
V
Receiver
Timing Chart
Code
registration
switch
OPERATION IN CODE REGISTRATION MODE
(PROGRAMMING)
When the code registration switch is in the
or
position, the receiver enters the registration mode where it
stores the first received secret code in the EEPROM.
Two different secret codes can be stored with the switch in
the
and
positions. Therefore, the user can use
two transmitters.
SET-l
FIX
SET-II
Signal sent from
transmitter A
Signal sent from
transmitter B
Valid
Signal received
by receiver
SET-I Starts accepting
secret code
to be stored.
Invalid
Valid
Invalid
I
Secret code is stored in EEPROM when
the switch is changed over from SET-l
or SET-II to FIX.
Electric Sunroof
l
If an obstruction interferes with the sliding open
motion, the roof lid glass immediately stops.
l
If an obstruction interferes with the sliding close
or tilt down motion, the roof lid glass will auto-
matically reverse.
l
Even after the ignition switch has been placed
at OFF, the sunroof can be operated for 30
seconds. When a door is opened during the
period, the sunroof can be operated for another
30 seconds from that time.
SUNROOF CONTROL SYSTEM
The motor driven outer slide glass sunroof tilt-up
mechanism is an option for all models. This glass
sunroof provides a well-lighted, open environment
even with the roof lid glass in the fully closed state.
The sun roof provides the following features.
To slide open or close the sunroof or tilt it up
or down, you don’t have to continue to press
the switch like the conventional one. The sunroof
operates at the touch of the switch.
If motion of the roof lid glass is interrupted during
a tilt-up operation, the tilt up operation does
not stop until the roof lid glass reaches the fully
tilted up state.
Components
Roof lid glass
hose
7 .
Tilt-down
and
Sunroof control uni
sliding close
control
sliding c
control
BODY Electric Sunroof
SUNROOF CONTROL UNIT
The microcomputer in the sunroof control unit
The sunroof motor drive circuits, incorporated in
trols several functions with two different signals (tilt
the sunroof control unit, operate under control of
up and sliding open, tilt down and sliding close)
the microcomputer.
from various points: the sunroof switches, the door
switch.
System diagram
Ignition switch
Sunroof control unit
--
--
Motor
Sunroof switch
1
1
Tilt-up, Sliding open
Microcomputer
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст