Mitsubishi Space Star. Manual — part 108
MANUAL TRANSMISSION –
Transmission Assembly <F5MV1>
22-9
REMOVAL SERVICE POINTS
A
TRANSMISSION MOUNT BRACKET REMOVAL
Jack up the transmission assembly gently with a garage jack,
and then remove the transmission mount bracket.
B
ENGINE ASSEMBLY SUPPORTING
Set the special tool to the vehicle to support the engine
assembly.
C
TIE ROD END DISCONNECTION
Caution
1.
Loosen the nut only; do not remove it from the ball
joint. Otherwise ball joint thread will be damaged.
2.
The special tool should be suspended by a cord to
prevent it from coming off.
D
DRIVE SHAFT <L.H.>/DRIVE SHAFT <R.H.>
DISCONNECTION
1.
Insert a pry bar between the transmission case and the
drive shaft as shown to remove the drive shaft.
NOTE
Do not remove the hub and knuckle from the drive shaft.
Caution
Always use a pry bar, or the T.J. will be damaged.
2.
Suspend the removed drive shaft with a wire so that there
are no sharp bends in any of the joints.
3.
Use a shop towel to cover the transmission case not to
let foreign material get into it.
MB991453
MZ203827
MB991113 or
MB990635
Cord
Ball joint
Nut
Pry bar
Trans-
mission
side
MANUAL TRANSMISSION –
Transmission Assembly <F5MV1>
22-10
INSTALLATION SERVICE POINTS
A
STABILIZER BAR INSTALLATION
Tighten the self-locking nut so that the stabilizer bar mounting
bolt protrudes as shown.
Standard value (A): 22 mm
B
TRANSMISSION MOUNT STOPPER INSTALLATION
Install the transmission mount stopper so that the arrow points
as shown in the illustration.
A
Engine side
Arrow
Transmission
mount stopper
Transmission
mount bracket
23-1
CONTENTS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
<A/T Key Interlock and Shift Lock
Mechanisms>
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . .
Essential Service
41
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
A/T Control Component Location
47
. . . . . . . . . . . . .
A/T Control Component Check
48
. . . . . . . . . . . . . . .
Torque Converter Stall Test
50
. . . . . . . . . . . . . . . . . .
Hydraulic Pressure Test
51
. . . . . . . . . . . . . . . . . . . . .
Hydraulic Circuit
56
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Line Pressure Adjustment
57
. . . . . . . . . . . . . . . . . . . .
Selector Lever Operation Check
57
. . . . . . . . . . . . . .
Transmission Control Cable Adjustment
60
. . . . . . .
SHIFT LOCK AND KEY INTERLOCK
MECHANISMS*
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
WARNINGS REGARDING SERVICING OF SUPPLEMENTAL RESTRAINT SYSTEM (SRS) EQUIPPED VEHICLES
WARNING!
(1) Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to personal
injury or death to service personnel (from inadvertent firing of the air bag) or to the driver and passenger (from
rendering the SRS inoperative).
(2) Service or maintenance of any SRS component or SRS-related component must be performed only at an authorized
MITSUBISHI dealer.
(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B – Supplemental
Restraint System (SRS) before beginning any service or maintenance of any component of the SRS or any SRS-related
component.
NOTE
The SRS includes the following components: SRS-ECU, SRS warning lamp, air bag module, clock spring and interconnecting
wiring. Other SRS-related components (that may have to be removed/installed in connection with SRS service or maintenance)
are indicated in the table of contents by an asterisk (*).
AUTOMATIC TRANSMISSION –
General/Service Specifications/
Lubricant/Special Tools
23-2
GENERAL
The following service procedures have been established to correspond to the introduction of the F4A42
type transmission.
SERVICE SPECIFICATIONS
Items
Standard value
Oil temperature sensor k
Ω
at 0
C
16.7 – 20.5
at 20
C
7.3 – 8.9
at 40
C
3.4 – 4.2
at 60
C
1.9 – 2.2
at 80
C
1.0 – 1.2
at 100
C
0.57 – 0.69
Resistance of damper clutch control solenoid valve coil (at 20
C)
Ω
2.7 – 3.4
Resistance of Low-Reverse solenoid valve coil (at 20
C)
Ω
2.7 – 3.4
Resistance of second solenoid valve coil (at 20
C)
Ω
2.7 – 3.4
Resistance of underdrive solenoid valve coil (at 20
C)
Ω
2.7 – 3.4
Resistance of overdrive solenoid valve coil (at 20
C)
Ω
2.7 – 3.4
Stall speed r/min
2,200 – 2,700
LUBRICANT
Items
Specified lubricant
Quantity L
Transmission fluid
DIA QUEEN ATF SP
II
M or ATF SP
III
7.8
SPECIAL TOOLS
Tool
Number
Name
Use
MB991502
MUT-
II
sub
assembly
Checking of the diagnosis code
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст