Mitsubishi Outlander PHEV (2019 year). Instruction — part 31
NOTE
l
When it rains or when the vehicle has been
washed, the inside of the lens sometimes be-
comes foggy. This is the same phenomenon
as when window glass mists up on a humid
day, and does not indicate a functional prob-
lem.
When the lamp is switched on, the heat will
remove the fog. However, if water gathers
inside the lamp, we recommend you to have
the lamp checked.
Bulb location and capacity
E01003201747
CAUTION
l
When replacing a bulb, be sure to use a new
bulb of the same type, wattage and colour. If
you install a different bulb, the bulb could
malfunction or fail to come on and could
lead to a vehicle fire.
Outside
E01003305498
Front
Type A
Type B
Type A: Halogen headlamps type
Type B: LED headlamps type
1- Front turn-signal lamps: 21 W (PY21W)
2- Headlamps, high-beam
Halogen: 60 W (HB3)
LED: −
3- Headlamps, low beam
Halogen: 55 W (H7)
LED: −
4- Position lamps: −
Daytime running lamps: −
5- Front fog lamps
Halogen: 19 W (H16)
LED: −
6- Side turn-signal lamps: −
Codes in parentheses indicate bulb types.
NOTE
l
The following lamps use an LED instead of
the bulb. If you need to repair or replace
these lamps, contact a MITSUBISHI
MOTORS Authorized Service Point.
•
Headlamps, high-beam (LED type)
•
Headlamps, low beam (LED type)
•
Position lamps
•
Daytime running lamps
•
Front fog lamps (LED type)
•
Side turn-signal lamps
Replacement of lamp bulbs
11-25
OGGE19E1
Maintenance
11
Rear
1- High-mounted stop lamp: −
2- Tail lamps: −
3- Charging port courtesy lamp: 5W
(W5W)
4- Rear fog lamp (LHD vehicles): 21 W
(W21W)
Reversing lamp (RHD vehicles): 16 W
(W16W)
5- Licence plate lamps: 5 W (W5W)
6- Reversing lamp (LHD vehicles): 16 W
(W16W)
Rear fog lamp (RHD vehicles): 21 W
(W21W)
7- Rear turn-signal lamps: 21 W (WY21W)
8- Stop lamps: −
Codes in parentheses indicate bulb types.
NOTE
l
The following lamps use an LED instead of
the bulb.
If you need to repair or replace these lamps,
contact a MITSUBISHI MOTORS Author-
ized Service Point.
•
High-mounted stop lamp
•
Tail lamps
•
Stop lamps
Inside
E01003403756
1- Luggage room lamp: 8 W
2- Room lamp (rear): 8 W
3- Map & room lamps (front): 8 W
4- Downlight
5- Vanity mirror lamps: 2 W
6- Glove box lamp: 1.4 W
NOTE
l
The following lamps use an LED instead of
the bulb. If you need to repair or replace
these lamps, contact a MITSUBISHI
MOTORS Authorized Service Point.
•
Downlight
•
Front foot lamps
Headlamps (low beam, halogen
bulb)
E01009301506
1. When replacing the bulb on the left side
of the vehicle, remove the bolt (A) hold-
ing down the relay box and move the re-
lay box.
*: Front of the vehicle
Replacement of lamp bulbs
11-26
OGGE19E1
Maintenance
11
2. Turn the cap (B) anticlockwise to re-
move it.
*: Front of the vehicle
3. Turn the socket (C) anticlockwise to re-
move it, and then pull the bulb out of the
socket.
4. To install the bulb, perform the removal
steps in reverse.
NOTE
l
When installing the bulb, align the tab (D)
with the notch (E) of the socket.
Headlamps (high-beam, halo-
gen bulb)
E01009401376
1. When replacing the bulb on the right
side of the vehicle, remove the clip (A)
holding down the washer tank spout and
then move it.
*: Front of the vehicle
2. Turn the cap (B) anticlockwise to re-
move it.
*: Front of the vehicle
Replacement of lamp bulbs
11-27
OGGE19E1
Maintenance
11
3. Turn the bulb (C) anticlockwise to re-
move it, and then while holding down
the tab (D), pull out the bulb (E).
4. To install the bulb, perform the removal
steps in reverse.
Front turn-signal lamps
E01003802320
CAUTION
l
Make sure that the Plug-in Hybrid EV sys-
tem have cooled down before replacing the
bulb on the right side of the vehicle, other-
wise you could be burnt by the radiator hose.
1. Remove the 12 clips (A, B), and then re-
move the cover (C).
2. Turn the socket (D) anticlockwise to re-
move it, then remove the bulb from the
socket by turning it anticlockwise while
pressing in.
*: Front of the vehicle
3. To install the bulb, perform the removal
steps in reverse.
Front fog lamps (Halogen bulb
type)*
E01004003674
1. Insert a straight blade (or minus) screw-
driver with a cloth over its tip at the
Replacement of lamp bulbs
11-28
OGGE19E1
Maintenance
11
points indicated by arrows and pry gen-
tly to remove the cover (A).
2. Remove the 3 screws (B) and remove
the lamp unit.
NOTE
l
When unfastening the screws of the fog
lamp, be careful not to mistakenly move the
beam position adjustment screw (C).
3. While holding down the tab (D), pull out
the socket (E).
4. Turn the bulb (F) anticlockwise to re-
move it.
5. To install the bulb, perform the removal
steps in reverse.
Replacement of lamp bulbs
11-29
OGGE19E1
Maintenance
11
Rear fog lamp (driver’s side)/
Reversing lamp (Passenger’s
side)
E01004101655
1. Insert a straight blade (or minus) screw-
driver with a cloth over its tip at the edge
of the lamp unit, and then push the lamp
unit upward to remove it.
2. Turn the socket (A) anticlockwise to re-
move it, and then pull the bulb out of the
socket.
3. To install the bulb, perform the removal
steps in reverse.
NOTE
l
When installing the lamp unit, first insert the
notch (B) into the hole on the body, and then
push on the lamp unit to fit it into place.
Rear combination lamps
E01004202767
1. Open the tailgate.
Replacement of lamp bulbs
11-30
OGGE19E1
Maintenance
11
2. Remove the screws (A), and then move
the lamp unit towards the rear of the ve-
hicle to unfix the notch (B) and pins (C)
of the lamp unit.
3. Turn the socket anticlockwise and re-
move it, and then pull the bulb out of the
socket.
D- Rear turn-signal lamp
E- Tail lamp and stop lamp (LED)-cannot
be replaced
NOTE
l
The tail lamp and stop lamp use an LED in-
stead of the bulb.
If you need to repair or replace these lamps,
contact a MITSUBISHI MOTORS Author-
ized Service Point.
4. To install the bulb, perform the removal
steps in reverse.
NOTE
l
When installing the lamp unit, align the
notch (F) and pin (G) on the lamp unit with
the clip (H) and hole (I) in the body.
Licence plate lamps
E01004602325
1. Remove while pressing the lamp unit
(A) to the left side of the vehicle.
2. Insert a minus screwdriver with the end
covered with a cloth or other object to
press the hook (B) aside and remove the
lens.
Replacement of lamp bulbs
11-31
OGGE19E1
Maintenance
11
3. Remove the bulb from the socket.
4. To install the bulb, perform the removal
steps in reverse.
NOTE
l
When installing the lamp unit, first insert the
end of tab (C) and then align tab (D).
Replacement of lamp bulbs
11-32
OGGE19E1
Maintenance
11
Vehicle labeling. . . . . . . . . . . . . . . . . . . . .12-02
Vehicle dimensions. . . . . . . . . . . . . . . . . . ... 12-04
Vehicle performance. . . . . . . . . . . . . . . . . . . 12-05
Vehicle weight. . . . . . . . . . . . . . . . . . . . ...12-05
Engine specifications. . . . . . . . . . . . . . . . . . 12-06
Charging system specifications. . . . . . . . . . . . . . .12-07
Electric motor specifications. . . . . . . . . . . . . . . .12-08
Low voltage electrical system. . . . . . . . . . . . . . ...12-08
Tyres and wheels. . . . . . . . . . . . . . . . . . . ...12-09
Fuel consumption. . . . . . . . . . . . . . . . . . . ..12-09
Capacity. . . . . . . . . . . . . . . . . . . . . . . 12-10
Specifications
OGGE19E1
12
Vehicle labeling
E01100105571
Vehicle identification number
The vehicle identification number is stamped
on the bulkhead as shown in the illustration.
Vehicle information code plate
The vehicle information code plate is riveted
as shown in the illustration.
The plate shows the model code, engine
model, transaxle model and body colour
code, etc.
Please use this number when ordering re-
placement parts.
1- Model code
2- Engine model code
3- Transaxle model code
4- Body colour code
5- Interior code
6- Option code
7- Exterior code
Vehicle identification number
plate (RHD vehicles only)
The vehicle identification number is stamped
on the plate riveted to the left front corner of
the instrument panel pad. It is visible from
outside of the vehicle through the wind-
screen.
Vehicle labeling
12-02
OGGE19E1
Specifications
12
Engine model/number
The engine model and number are stamped
on the engine cylinder block as shown in the
illustration.
*: Front of the vehicle
Electric motor model/number
The electric motor model and number are
stamped as shown in the illustration.
1- Front motor
2- Rear motor
*: Front of the vehicle
Vehicle labeling
12-03
OGGE19E1
Specifications
12
Vehicle dimensions
E01100205178
1
Front track
1,540 mm
2
Overall width
1,800 mm
3
Front overhang
990 mm
4
Wheel base
2,670 mm
5
Rear overhang
1,035 mm
6
Overall length
4,695 mm
7
Ground clearance (un-
laden)
Without exhaust pipe protector
190 mm
8
With exhaust pipe protector
185 mm
9
Overall height (unladen)
1,710 mm
10
Rear track
1,540 mm
Vehicle dimensions
12-04
OGGE19E1
Specifications
12
Minimum turning radius
Body
5.76 m
Wheel
5.3 m
Vehicle performance
E01100303553
Maximum speed
170 km/h
Vehicle weight
E01100409309
Item
Except for S Edition
S Edition
LHD
RHD
LHD
RHD
Kerb weight
Without
op-
tional parts
1,880 kg
1,900 kg
With full op-
tional parts
1,947 kg
1,945 kg
1,957 kg
1,955 kg
Maximum gross vehicle weight
2,390 kg
Maximum
axle
weight
Front
1,200 kg
Rear
1,255 kg, 1,365 kg
*
Maximum towable
weight
With brake
1,500 kg
Without brake
750 kg
Maximum trailer-nose weight
75 kg
*
: In case of trailer towing
Vehicle performance
12-05
OGGE19E1
Specifications
12
Item
Except for S Edition
S Edition
LHD
RHD
LHD
RHD
Maximum roof load
80 kg
Seating capacity
5 persons
*
: In case of trailer towing
NOTE
l
Trailer specifications indicate the manufacturer’s recommendation.
Engine specifications
E01100604856
Engine model
4B12
No. of cylinders
4 in line
Total displacement
2,360 cc
Bore
88.0 mm
Stroke
97.0 mm
Camshaft
Double overhead
Mixture preparation
Electronic injection
Maximum output (EEC net)
99 kW/4,500 rpm
Maximum torque (EEC net)
211 N•m/4,500 rpm
Engine specifications
12-06
OGGE19E1
Specifications
12
Charging system specifications
E01101901190
Normal charging system
Rated input voltage
AC 230V (single phase)
Rated input frequency
50 Hz/60 Hz
Maximum rated current
10 A
*1
, 8 A
*1
Maximum power consumption
3.6 kVA
*2
Applicable standards
Charging cable
(with connector
and control box)
EN61851-1
IEC61851-1
IEC62196-1
On board charger
EN61851-21
IEC61851-21
Leakage current sensitivity in cable control box
20 mA
Charging mode
Based on IEC61851-1
Mode 2/Case B
*1
Mode 3/Case C
*2
IP degrees
IP44: When a charge connector is connected
IP55: When charging lid is closed and vehicle is moving
Quick charging system
Applicable standards
IEC62196-1
CHAdeMO
Maximum input current
60 A
*1
: When using a genuine charging cable with control box
*2
: When using a home or public charging device (EVSE: Electric Vehicles Supply Equipment)
Charging system specifications
12-07
OGGE19E1
Specifications
12
IP degrees
IP44: When a charge connector is connected
IP55: When the charging lid is closed and the vehicle is
moving
*1
: When using a genuine charging cable with control box
*2
: When using a home or public charging device (EVSE: Electric Vehicles Supply Equipment)
Electric motor specifications
E01100604869
Item
Front Motor
Rear Motor
Electric motor model
S61
Y61
Maximum output (ECE net)
60 kW
70 kW
Maximum torque
137 Nm
195 Nm
Maximum 30 minutes power
25 kW
Low voltage electrical system
E01100804151
Voltage
12 V
Auxiliary battery
Type (JIS)
S46B24L(S)
Capacity (5HR)
36 Ah
Spark plug type
NGK
DIFR5E11
Electric motor specifications
12-08
OGGE19E1
Specifications
12
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст