Mitsubishi Lancer Evolution 8. Manual — part 106
BODY – BONNET, DOORS
42-3
Installation service point
A
Bonnet hinge bolt installation
Caution
Because the bonnet is made from aluminium, a special coating is
provided on the bonnet hinge bolt (bonnet side), and therefore
special parts should be used.
DOORS
Door handles and latches
Removal and Installation
Pre-Removal Operations
• Door trim removal
Post-Removal Operations
• Door inside handle looseness check
• Door outside handle looseness check
• Door trim installation
Removal procedure
1. Door inside handle
• Waterproof film
2. Door outside handle
3. Key cylinder
4. Lower sash
5. Door latch assembly
6. Link
(Front door)
(Rear door)
A
B
BODY – DOORS
42-4
Installation service point
The installation points are the same as the previous model.
INSPECTION
Front door lock actuator check
Rear door lock actuator check
Rod position
Terminal No.
1 2 3 4 6
Rod operation
Actuator
Lock
Unlock
Lock to Unlock
Unlock to Lock
Latch
Lock
Unlock
Lever position
Terminal No.
4
6
Lever operation
Lock
Lock to Unlock
Unlock
Unlock to Lock
Front
(Left side)
Lock
Unlock
Lever
(Right side)
Unlock
Lock
Lever
View A
View B
Rear
(Left side)
Lock
Unlock
Lever
(Right side)
Unlock
Lock
Lever
View A
View B
⊕
⊕
⊕
⊕
-
-
-
-
BODY – BOOT LID, KEYLESS ENTRY SYSTEM
42-5
Boot Lid
The following servicing information now applies, due to changes in the boot lid torsion bar. Apart from the points described
below, the servicing information is the same as that for the previous model.
Keyless Entry System
With the addition of the security alarm function to the keyless entry system, the following servicing information now applies.
With the exception of these details, the servicing information is the same as that for the previous model.
Troubleshooting
Diagnosis function
For troubleshooting information, see Chapter 54B – SWS.
On-vehicle Service
1. Encrypted code registration method
Unique encrypted codes are registered in each transmitter, and in
the following cases, this code must be re-registered in the
EEPROM in the ETACS-ECU.
• If the transmitter or the ETACS-ECU is replaced
• If a transmitter is added
• If an encrypted code registration error is thought to be the cause
of a problem.
Up to four different encrypted codes for four different transmitters
can be stored in the EEPROM memory space. When the first code
is registered, all previous encrypted codes are erased. This means
that when there are two or more transmitters, or when a transmitter
is added, all of the codes must be re-registered.
1. Check that the normal door lock function is working at the door
key cylinder.
2. Insert the ignition key into the ignition switch.
3. Connect the MUT-II/III to the diagnosis connector.
Remarks
If no MUT-II/III is present, the system is set to an encrypted code
registration ready state, by earthing the No.1 terminal of the
diagnosis connector.
Caution
The ignition switch must be set to the LOCK(OFF) position
when connecting or disconnecting the MUT-II/III (connecting or
disconnecting the earth).
Installation service points
A
Boot lid torsion bar installation
Apart from the identification colours used for the boot lid torsion
bar, the procedure is the same as in the previous model.
Boot lid torsion bar
Identification colour
LH
Vehicle fitted with rear spoiler
Vehicle not fitted with rear spoiler
Green
None
RH
Vehicle fitted with rear spoiler
Vehicle not fitted with rear spoiler
Yellow
Red
BODY – BONNET
42-6
4. Switch the hazard switch ON and OFF 6 times, within the space of
10 seconds after connecting to the MUT-II/III (earth connection).
Remarks
(1) When these 6 on/off operations are completed, the door lock locks
and unlocks once, and assumes a registration mode.
(2) The ON/OFF status of the hazard switch changes each time the
hazard switch is pressed.
5. Press the transmitter switch and then press it twice again within 10
seconds to register the code.
6. When registration is complete, the door lock will automatically lock
and unlock once.
7. If there are two or more transmitters or if a transmitter is to be
added, then all the transmitters must be registered within one minute
after setting the registration mode. The registration method is the
same as that for the first code.
8. The registration mode terminates in any of the following cases.
• When encrypted codes for four transmitters have been registered.
• When one minute has passed after entering registration mode.
• When the MUT-II/III connection is removed (earth is disconnected).
• When the ignition key is removed.
9. After registration mode has terminated, use the following procedure
to check the operation of the keyless entry system.
• Remove the ignition key
• Close all doors
Hazard
switch
Connect to MUT-II
Within 10 seconds
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст