Mitsubishi Lancer Evolution 8. Manual — part 125
SWS – TROUBLESHOOTING
54B-23
Trouble Symptom
Inspection
Procedure No.
Reference
page
Interior light does not light up or switch off correctly
N-1
54B-88
Interior light
Interior light automatic cut-off function not working
correctly (cars fitted with keyless entry system)
N-2
54B-91
Half door
indicator lamp
Half door indicator light does not light up or switch off
correctly
O-1
54B-92
Security alarm does not enter warning state
P-1
54B-93
Interior warning does not operate correctly when security
alarm operates
P-2
54B-94
Hazard lights do not flash when security alarm operates
P-354B-94
Security alarms
Phone does not ring when security alarm operates
P-4
54B-95
Multi-centre
display
Multi-centre display not working correctly
Q-1
See Chap.
54A*
Note * : See ’00-5 Lancer Cedia Servicing Manual (No.1036K00)
Door ajar
Door ajar
Horn does not sound when security alarm operates
SWS – TROUBLESHOOTING
54B-24
9. Confirming problems in input signal check
(Service data, Diagnosis by Function or Pulse Check)
If a problem arises during the service data service points, then perform an inspection by referring to the table below.
Trouble Symptom
Inspection
Procedure
No.
Reference
page
Ignition switch (ACC) signal not input
R-1
54B-96
Ignition switch (IG1) signal not input
R-2
54B-96
Reversing light switch signal not input
R-354B-97
Driver’s door switch signal not input
R-4
54B-98
Tail light switch signal not input
Headlight switch signal not input
Dimmer switch signal not input
Passing switch signal not input
LH turn indicator light switch signal not input
RH turn indicator light switch signal not input
R-5
54B-99
Windscreen mist wiper switch signal not input
Windscreen intermittent wiper switch signal not input
Windscreen low speed wiper switch signal not input
Windscreen high speed wiper switch signal not input
Windscreen washer switch signal not input
Rear wiper switch signal not input
Rear washer switch signal not input
R-6
54B-100
Column switches
Windscreen intermittent wiper volume signal not input
R-7
54B-101
Electric window
main switch
Respective switch signals not input
R-8
54B-101
Sunroof
Respective switch signals not input
R-9
54B-102
Multi-centre
display
Respective switch signals not input
R-10
54B-103
Key reminder switch signal not input
R-11
54B-103
Motorized remote control mirror switch (fold / return switch) signal not input
R-12
54B-104
Hazard light switch signal not input
R-1354B-105
All door switch signals not input (except driver’s door)
R-14
54B-106
Driver’s door lock actuator signal not input
R-15
54B-107
Vehicle speed signal not input
R-16
54B-108
Various switch signals of keyless entry transmitter not input
R-17
54B-109
Fog light switch signal not input
R-18
54B-110
Generic fuse No.17 load use signal not detected
R-19
54B-111
SWS – TROUBLESHOOTING
54B-25
Chart of operational functions classified by input signal inspection procedure number
If a problem arises in a number of different functions when using the SWS, perform an input signal check by referring to the
table below.
(Only the input signals and functions which may possibly give rise to multiple problems are listed in the table)
Name of function
R-1
R-2
R-3
R-4
R-5
R-6
R-11 R-13 R-14 R-15
R-16 R-17 R-19
Ignition key left in reminder warning
●
●
●
Lights left on reminder warning
●
●
●
Door ajar warning function
●
●
●
Turn indicator light operating noise
●
●
Central door locking control
●
Keyless entry
●
●
●
●
●
●
Keyless entry answer back
●
●
Multi-mode keyless entry
●
Electric window control
●
Electric window timer
●
●
Sunroof control
●
Windscreen wiper & washer control
●
●
●
Rear wiper & washer control
●
●
●
Motorized retractable door mirror control
●
●
Ignition key cylinder illumination light control
●
●
●
●
Tail light control
●
Headlight control
●
Headlight automatic cut-off
●
●
●
Fog light control
●
Turn indicator light control
●
●
Hazard light control
●
Interior light control
●
●
●
●
●
●
Interior light automatic cut-off
●
●
Door ajar indicator lamp
●
●
●
Security alarm
●
●
●
●
●
SWS – TROUBLESHOOTING
54B-26
10. Inspection Procedures Classified by Trouble Symptoms
Inspection Procedure
Can the MUT-II/III communicate with other systems?
Is communication with the MUT-II/III possible when the
ignition switch is set to the ON position?
Check connector C-225
Measure at ETACS-ECU connector C-225
• Detach the connector, and measure at the junction box
side
• Connectivity between 56 and body earth
OK: No connectivity
Check connectors C-06, C-122
Check the harness between the ETACS-ECU and the
diagnosis connectors
Confirm the trouble symptoms
Transient problem
Check MUT-II/III diagnosis circuit, and repair
Inspection procedure A-3 “No communication with
ETACS-ECU”. See p.54B-28
Check connector C-107
Check the harness between the ETACS-ECU and body
earth
Replace the ETACS-ECU
No communication with SWS monitor
Probable Cause
There may be a malfunction in the connections to the SWS
monitor
• Fault in SWS monitor main unit (I/F cartridge)
• Fault in SWS monitor harness
• Fault in harness / connectors
• Fault in ETACS-ECU
YES
NO
NO
YES
NG
NG
NG
NG
OK
OK
OK
OK
OK
NG
Repair
OK
NG
Repair
Repair
Repair
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст