Mitsubishi Lancer Evolution IX. Manual — part 652
AIR BAG MODULE AND SEAT BELT PRE-TENSIONER DISPOSAL PROCEDURES
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-121
7. Cut with a pliers, etc. the instrument panel wiring
harness shown in the figure of the instructions,
while the C-205 clock spring connector is
disconnected.
NOTE: The disconnection location should be suf-
ficiently away from the C-205 harness side con-
nector with consideration to the expansion
harness connection location upon disconnections.
8. Connect the deployment wires on the two
instrument panel wiring harnesses disconnected,
cover the connection areas with insulator tape
and then pull out the deployment wires outside the
vehicle.
9. Connect the C-205 harness side connector
connected with an expansion harness to the
C-205 clock spring connector.
WARNING
If the glass is scratched, air bag deployment
could cause it to crack and fly out of the
vehicle, so always put a cover over the vehi-
cle.
10.To suppress the operation sound as much as
possible completely close all door windows, close
the doors and put the cover on the vehicle.
WARNING
•
Before deploying the air bag in this man-
ner, first check to be sure that there is no
one in or near the vehicle. Wear safety
glasses.
•
The inflator will be quite hot immediately
following the deployment, so wait at least
30 minutes to allow it to cool before
attempting to handle it. Although not poi-
sonous, do not inhale gas from the air bag
deployment. See Deployed Air Bag Mod-
ule and Operated Seat Belt Pre-tensioner
Disposal (Refer to
) for
post-deployment handling instructions.
•
If the air bag module fails to deploy, do
not go near the module. Contact your dis-
tributor.
11.At a location as far away from the vehicle as
possible, disconnect the two connected wires
from each other, and connect them to the two
terminals of the battery (which has been removed
from the vehicle) to deploy the air bag.
12.After deployment, dispose of the air bag module
according to the Deployed Air Bag Module and
Operated Seat Belt Pre-tensioner Disposal (Refer
to
).
DEPLOYMENT INSIDE THE VEHICLE
(WHEN DISPOSING OF A VEHICLE)
<PASSENGER'S (FRONT) AIR BAG
MODULE>
1. Move the vehicle to an isolated spot.
DANGER
Wait at least 60 seconds after the disconnec-
tion of the battery cable before any further
job (Refer to
2. Disconnect the negative and positive battery
cables from the battery terminals, and then
remove the battery from the vehicle.
3. Remove the glove box (Refer to GROUP 52A
−
Instrument Panel
AC300388AD
Cover
Deployment wire
6 m or longer
AIR BAG MODULE AND SEAT BELT PRE-TENSIONER DISPOSAL PROCEDURES
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-122
4. Remove the connection between the C-106
passenger's (front) air bag module connector
(2-pin, red) and the harness side connector (2-pin,
red).
NOTE: Once disconnected from the instrument
panel wiring harness, both electrodes of the pas-
senger's (front) air bag module short automati-
cally. This prevents the passenger's (front) air bag
from accidental deployment caused by static, etc.
5. Connect deployment wires longer than 6 m to
each SRS air bag adapter harness (MB686560)
and insulate the connections with insulator tape.
Also, connect the deployment wires in the other
ends to short, thereby preventing the passenger's
(front) air bag from accidental deployment caused
by static etc.
6. Connect the C-106 passenger's (front) air bag
module connector (2-pin, red) to special tool SRS
air bag adapter harness (MB686560) and move
the deployment wires out of the vehicle.
WARNING
If the glass is scratched, air bag deployment
could cause it to crack and fly out of the
vehicle, so always put a cover over the vehi-
cle.
7. To suppress the operation sound as much as
possible completely close all door windows, close
the doors and put the cover on the vehicle.
WARNING
•
Before deploying the air bag in this man-
ner, first check to be sure that there is no
one in or near the vehicle. Wear safety
glasses.
•
The inflator will be quite hot immediately
following the deployment, so wait at least
30 minutes to allow it to cool before
attempting to handle it. Although not poi-
sonous, do not inhale gas from the air bag
deployment. See Deployed Air Bag Mod-
ule and Operated Seat Belt Pre-tensioner
Disposal (Refer to
) for
post-deployment handling instructions.
•
If the air bag module fails to deploy, do
not go near the module. Contact your dis-
tributor.
8. At a location as far away from the vehicle as
possible, disconnect the two connected wires
from each other, and connect them to the two
terminals of the battery (which has been removed
from the vehicle) to deploy the air bag.
9. After deployment, dispose of the air bag module
according to the Deployed Air Bag Module and
Operated Seat Belt Pre-tensioner Disposal (Refer
to
).
AC100985
Connector: C-106
Glove box striker
AT
C-106 Passenger's (front)
air bag module connector
(2-pin, red)
AC300419AC
Connection
Deployment wires
MB686560
Insulator tape
6 m or longer
AC300420AK
MB686560
C-106 Passenger's (front)
air bag module connector
(2-pin, red)
Deployment wires
AC300388AD
Cover
Deployment wire
6 m or longer
AIR BAG MODULE AND SEAT BELT PRE-TENSIONER DISPOSAL PROCEDURES
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-123
DEPLOYMENT INSIDE THE VEHICLE
(WHEN DISPOSING OF A VEHICLE)
<SEAT BELT PRE-TENSIONER>
1. Move the vehicle to an isolated spot.
DANGER
Wait at least 60 seconds after disconnecting
the battery cables before doing any further
work (Refer to
2. Disconnect the negative and positive battery
cables from the battery terminals, and then
remove the battery from the vehicle.
3. Remove the centre pillar lower trim (Refer to
GROUP 52A
).
4. Execute the following steps to disconnect the
connection between D-03 or D-16 seat belt
pre-tensioner connector (2-pin) and harness side
connector (2-pin, black).
NOTE: Once disconnected from the floor wiring
harness, both electrode of the seat belt pre-ten-
sioner connector short automatically. This pre-
vents the seat belt pre-tensioner from accidental
deployment caused by static etc.
(1) Use a flat-tipped screwdriver to pull out
forward and unlock the locking button of the
harness-side connector (2-pin, black).
(2) Disconnect the D-03 or D-16 harness side
connector.
5. Connect deployment wires longer than 6 m to
each special tool SRS air bag adapter harness
(MB991885) and insulate the connections with
insulator tape. Also, connect the deployment
wires in the other ends to short, thereby
preventing the seat belt pre-tensioner from
accidental deployment caused by static etc.
6. Connect the D-03 or D-16 seat belt pre-tensioner
2-pin connector (black) to special tool SRS air bag
adapter harness (MB991885) and move the
deployment harness out of the vehicle.
WARNING
•
Before operating the seat belt pre-ten-
sioner in this manner, first check to be
sure that there is no one in or near the
vehicle. Wear safety glasses.
•
The inflator will be quite hot immediately
following the operation, so wait at least 30
minutes to allow it to cool before attempt-
ing to handle it. Although no poisonous,
do not inhale gas from the seat belt
pre-tensioner operation. See Deployed Air
Bag and Operated Seat Belt pre-tensioner
Disposal (Refer to
) for
post-operation handling instructions.
•
If the seat belt pre-tensioner fails to oper-
ate, do not go near the seat belt pre-ten-
sioner. Contact your distributor.
7. At a location as far away from the vehicle as
possible, disconnect the two connected wires
from each the, and connect them to the two
terminals of the battery (which has been removed
from the vehicle) to operating the seat belt
pre-tensioner.
8. After operation, dispose of the seat belt
pre-tensioner according to the Deployed Air Bag
Module operated seat belt pre-tensioner Disposal
(Refer to
AC300446 AL
D-03 or D-16
Seat belt
pre-tensioner
connector (2-pin)
Flat-tipped
screwdriver
Locking button
D-03 or D-16
Harness side
connector
(2-pin, black)
AC300447
AC
Connection
Deployment wires
MB991885
Insulator tape
6 m or longer
AC300448AD
MB991885
Deployment
wires
D-03 or D-16
Seat belt
pre-tensioner
2-pin connector
AIR BAG MODULE AND SEAT BELT PRE-TENSIONER DISPOSAL PROCEDURES
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-124
DEPLOYMENT OUTSIDE THE VEHICLE
<DRIVER’S AIR BAG MODULE>
WARNING
•
This should be carried out in a wide, flat
area at least 6 m away from obstacles and
other people.
•
Do not deploy outside if wind is high.
Even in a soft wind, ignite to windward of
the air bag modules.
DANGER
Wait at least 60 seconds after disconnecting
the battery cables before doing any further
work (Refer to
1. Disconnect the negative and positive battery
cables from the battery terminals, and then
remove the battery from the vehicle.
WARNING
Once disconnected, both electrodes of the
driver’s air bag module connector short
automatically to prevent accidental deploy-
ment caused by static etc. Still, in considera-
tion of the accidental deployment, store the
air bag module on flat place with deployment
surface facing up. Also, do not put anything
on it.
2. Remove the driver’s air bag module from the
vehicle (Refer to
).
3. Obtain two suitable wires, which are 6 meters or
longer, as deployment wires. Then connect the
wires at one end to short.
4. Touch the vehicle’s body with bare hands to
discharge static in you.
5. Release the secured connector of the steering
wheel-driver's air bag module assembly to cut off
the connector from the harness with a nipper and
etc. Connect deployment harnesses to each of
two separated harnesses and cover the area with
insulator tape.
6. Use a rope to tie the steering wheel-driver's air
bag module assembly to secure old tyres with
wheels.
7. Route the deployment harness connected to
driver's air bag module beneath old tyres with
wheels. Then, secure the steering wheel-driver's
air bag module assembly with the deployment
surface facing up.
8. Place three old tyres without wheels on the tyre
secured with the driver’s air bag module.
AC300381AD
Deployment wires
Connection
6 m or longer
AC211892
Deployment
harness
Steering wheel-driver's
air bag module
assembly
Insulator tape
Connection
AE
AC211893
Steering wheel-driver's air bag
module assembly
Deployment
harness
AC
AC300478
Tyre without wheels
Deployment wires
AE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст