Mitsubishi Lancer Evolution IX. Manual — part 190

TROUBLESHOOTING

SMART WIRING SYSTEM (SWS) USING SWS MONITOR

54C-19

BUZZER

NOTE: The headlamp automatic shutdown function works in approximately one second after the lighting
monitor buzzer starts sounding, and then the buzzer ceases sounding.

PULSE CHECK

M1549015100421

CAUTION

Before connecting or disconnecting the
M.U.T.-II/III, turn the ignition switch to the "LOCK"
(OFF) position.

1. The input signals (signals other than communica-

tion line signals), which are compatible with the
SWS monitor by using the M.U.T.-II/III or voltme-
ter, can be confirmed by the Pulse Check.

NOTE: If a problem is found in the "Pulse Check",

refer to the Problems during Input Signal Check
<Service data, function diagnosis or pulse
check> (Refer to

P.54C-24

2. Use the M.U.T.-II/III or voltmeter to check the fol-

lowing input signals.

SWITCHES WHICH ARE APPLICABLE TO INPUT SIGNAL CHECK, AND THEIR CHECK
CONDITIONS

Item

Input signal

Item No. Display on M.U.T.-II/III

Normal condition

LGT
MONI_ALRM

Headlamp switch

HEADLAMP SW

Either is on

Tail lamp switch

TAIL LAMP SW

Ignition switch
(IG1)

IG SW(IG1)

OFF

Driver's door switch 32

DR DOOR SW

Headlamp
automatic
shutdown function

HD AUTO-CUT

OFF

Buzzer

BUZZER

Input signal

Requirements for sounding buzzer

Key reminder switch <vehicles with keyless entry system>

When the inserted ignition key is pulled out.

Hazard warning lamp switch

When the switch is turned from off to on.

All of the door switches

A door is opened when all the doors are
closed.

Driver's door lock actuator

When the driver's key cylinder or inside lock
knob is unlocked or locked.

Vehicle speed signal

When the vehicle speed has reached 10
km/h or more.

Keyless entry transmitter

Switches

When the switch is turned from off to on.

Interior lamp loaded signal

When a load is applied through
multi-purpose fuse No.18.

Door lock key cylinder switch

Turn the key to the lock or unlock position

TROUBLE SYMPTOM CHART

SMART WIRING SYSTEM (SWS) USING SWS MONITOR

54C-20

M.U.T.-II/III DRIVE RECORDER FUNCTION

M1549027300024

1. The SWS monitor cartridge memory can store the

ECU check results, the service data, the
communication data obtained by the function
diagnosis. This communication data can be
displayed as a chart or graphical form.

2. If data obtained by the M.U.T.-II/III drive recorder

function has to be stored for long time, the data
can be transferred to the SWS monitor cartridge.
By doing this, you can disconnect the M.U.T.-II/III
to prevent excessive battery drain.
NOTE: For the details about the M.U.T.-II drive
recorder function, refer to M.U.T.-II Reference
Manual.
NOTE: For the details about the M.U.T.-III drive
recorder function, refer to M.U.T.-III User’s Man-
ual.

TROUBLE SYMPTOM CHART

M1549000800877

Symptom

Inspection
procedure
number

Reference
page

Communication with the SWS monitor is not possible.

A-1

P.54C-26

Communication with the column switch (column-ECU) is not possible.

A-2

P.54C-30

Communication with the ETACS-ECU is not possible.

A-3

P.54C-36

Communication with the front-ECU is not possible.

A-4

P.54C-42

Communication with the power window main switch (power window
module) is not possible.

A-5

P.54C-47

TROUBLE SYMPTOM CHART

SMART WIRING SYSTEM (SWS) USING SWS MONITOR

54C-21

<FUNCTION SYSTEM>

Symptom

Inspection
procedure
number

Reference
page

Buzzer

Lamp reminder buzzer function does not work
normally.

B-1

P.54C-57

Central door locking
system

Central door locking system does not work. <LH
drive vehicles>

C-1

P.54C-59

Central door locking system does not work. <RH
drive vehicles>

P.54C-62

A door or a tailgate cannot be locked or unlocked
by the central door locking system. <LH drive
vehicles>

C-2

P.54C-65

A door or a tailgate cannot be locked or unlocked
by the central door locking system. <RH drive
vehicles>

P.54C-72

The central door locking system can not be
operated by means of the front passenger’s door
lock key cylinder.

C-3

P.54C-79

The ignition key reminder function does not work
normally.

C-4

P.54C-81

The impact detection door unlock function does
not function.

C-5

P.54C-83

Power windows

Power windows do not work at all.

D-1

P.54C-86

Driver's power window does not work by means
of the power window main switch. <LH drive
vehicles>

D-2

P.54C-89

Driver's power window does not work by means
of the power window main switch. <RH drive
vehicles>

P.54C-91

Relevant power window(s) do not work by means
of the front and rear passenger's power window
sub switches.

D-3

P.54C-93

Front and/or rear passenger's power window(s)
do not work by means of the power window main
switch.

D-4

P.54C-111

The window glass lowers automatically while it is
rising.

D-5

P.54C-123

Power window anti-trap function does not work
normally.

D-6

P.54C-124

TROUBLE SYMPTOM CHART

SMART WIRING SYSTEM (SWS) USING SWS MONITOR

54C-22

Keyless entry system Keyless entry system does not work.

E-1

P.54C-137

Keyless entry hazard warning lamp answerback
function or the room lamp answerback function
does not work normally.

E-2

P.54C-139

Encrypted code cannot be registered.

E-3

P.54C-140

The timer lock function does not work after the
doors have been unlocked by the keyless entry
system.

E-4

P.54C-141

Windshield wiper and
washer

The windshield wipers do not work at all.

F-1

P.54C-142

The windshield wipers do not work when the
wiper switch is at "INT", "WASHER" or "MIST"
position. However, the wipers work at low speed
when the switch is at "LO" and "HI" position.

F-2

P.54C-149

The windshield wipers do not stop at the
specified park position.

F-3

P.54C-151

The windshield wipers do not work normally.

F-4

P.54C-156

The intermittent wiper interval cannot be adjusted
by operating the windshield intermittent wiper
volume control.

F-5

P.54C-161

The intermittent wiper interval is not changed
according to the vehicle speed.

F-6

P.54C-162

The windshield washer does not work.

F-7

P.54C-164

Ignition key cylinder
illumination lamp

The ignition key cylinder illumination lamp does
not illuminate/extinguish normally.

G-1

P.54C-169

Headlamp and tail
lamp

The headlamps do not illuminate when the
lighting switch is at "TAIL" or "PASSING"
position, but illuminate only at low beam when
the switch is at "HEAD" position. However, the
headlamps do not illuminate at high beam.

H-1

P.54C-173

The tail lamps do not illuminate normally.

H-2

P.54C-174

The low-beam headlamps do not illuminate
normally.

H-3

P.54C-177

The high-beam headlamps do not illuminate
normally.

H-4

P.54C-180

The high-beam and low-beam headlamps do not
illuminate when the passing switch is operated.