Mitsubishi Lancer Evolution IX. Manual — part 274
MB991223
A
D
C
B
AZ
DO NOT USE
COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL
54A-33
TROUBLESHOOTING
SYMPTOM CHART
M1543007201280
Symptom
Inspection
procedure No.
Reference page
Speedometer does not work.
1
Tachometer does not work.
2
Fuel gauge does not work.
3
Engine coolant temperature gauge does not work.
4
Combination meters does not work.
5
MB991223
A: MB991219
B: MB991220
C: MB991221
D: MB991222
Harness set
A: Test harness
B: LED harness
C: LED harness
adapter
D: Probe
Making voltage and
resistance measurements
during troubleshooting
A: Connect pin contact
pressure inspection
B: Power circuit inspection
C: Power circuit inspection
D: Commercial tester
connection
MB992006
MB992006
Extra fine probe
Continuity check and voltage
measurement at harness wire
or connector
Tool
Number
Name
Use
COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL
54A-34
SYMPTOM PROCEDURES
INSPECTION PROCEDURE 1: Speedometer does not work.
AC504334
Speedometer Circuit
IGNITION
SWITCH (IG1)
FUSIBLE
LINK
1
COMBINATION
METER
SPEED
CONTROL CIRCUIT
VEHICLE
SPEED
SENSOR
DIAGNOSIS
CONNECTOR
FRONT SIDE
NOTE
: L.H. drive vehicles
: R.H. drive vehicles
Wire colour code
B : Black LG : Light green G : Green L : Blue
W : White Y : Yellow SB : Sky blue BR : Brown
O : Orange GR : Gray R : Red P : Pink V : Violet
AB
COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL
54A-35
TECHNICAL DESCRIPTION (COMMENT)
The cause may be a faulty vehicle speed sensor cir-
cuit system or a faulty speedometer. Vehicle speed
sensor is also used by the engine-ECU.
TROUBLESHOOTING HINTS
• Malfunction of the vehicle speed sensor
• Malfunction of the engine-ECU
• Malfunction of the combination meter assembly
• The wiring harness or connectors may have
loose, corroded, or damaged terminals, or termi-
nals pushed back in the connector.
DIAGNOSIS PROCEDURE
STEP 1. Check with other meter.
AC304777
Steering shaft
AB
MB991502
<Using the M.U.T.-II>
AC210056
MB991911
16-PIN
MB991827
MB991824
AF
<Using the M.U.T.-III>
Check to see that the tachometer, fuel gauge and
water thermometer are operating normally.
Q: Do all other meters operate?
YES <other meters all operate.> :
Go to Step 2.
NO <one or more of the other meters does not
operate.> :
Refer to INSPECTION PROCEDURE
STEP 2. Check the vehicle speed sensor.
(M.U.T.-II/III MPI diagnosis code)
AC304777
Steering shaft
AB
MB991502
<Using the M.U.T.-II>
AC210056
MB991911
16-PIN
MB991827
MB991824
AF
<Using the M.U.T.-III>
(1) Connect M.U.T.-II/III to the diagnosis connector.
(2) Turn the ignition switch to the "ON" position.
(3) Read the MPI system diagnosis code.
Q: Is MPI system diagnosis code P0500 set?
YES :
Refer to GROUP 13A
− Troubleshooting
.
NO :
Go to Step 3.
COMBINATION METER ASSEMBLY
CHASSIS ELECTRICAL
54A-36
STEP 3. Check combination meter connector
C-01 and vehicle speed sensor connector B-04
for loose, corroded or damaged terminals, or
terminals pushed back in the connector.
AC310439
Connector : B-04
AG
Harness side
B-04(B)
1
2
3
AC310446
Connector: C-01
<L.H. drive vehicles>
Harness side
BF
AC310456
Connector: C-01
<R.H. drive vehicles>
Harness side
AU
Q: Are combination meter connector C-01 and
vehicle speed sensor connector B-04 in good
condition?
YES :
Go to Step 4.
NO :
Repair or replace the damage
component(s).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст