Mitsubishi Lancer Evolution IX. Manual — part 301
PROPELLER SHAFT
PROPELLER SHAFT
25-7
DISASSEMBLY SERVICE POINTS
<<A>> COMPANION FLANGE REMOVAL
AC211610
Mating marks
AC
Make mating marks on the companion flange and
centre propeller shaft, and then remove the compan-
ion flange.
<<B>>CENTRE BEARING ASSEMBLY
REMOVAL
AC101273
Centre bearing
assembly
MD998801
AD
Use special tool bearing remover (MD998801) to
remove the centre bearing assembly from the centre
propeller shaft.
<<C>> BOLT REMOVAL
Make mating marks on the rear propeller shaft, LJ
assembly and companion flange, and then remove
the bolt.
<<D>>LJ ASSEMBLY REMOVAL
AC101274
LJ assembly
LJ boot
AE
1. Remove the LJ boot from the LJ assembly.
AC101275 AC
Outer race
Circlip
Ball
Cage
Inner
race
2. Make mating marks on the outer race, cage and
inner race, and then remove the circlip, outer race
and ball.
NOTE: Note the positions of the balls so that they
can be reinstalled in their original positions.
AC101276
Inner race
Puller
Cage
AC
3. Remove the inner race with cage from the centre
propeller shaft assembly by using a puller
(commercially available).
4. Wipe off the grease and clean the outer race,
inner race, cage and balls.
<<E>> LJ BOOT REMOVAL
When the LJ boot is reused, tape the spline part on
the centre propeller shaft and then remove the LJ
boot.
REASSEMBLY SERVICE POINTS
>>A<< LJ BOOT INSTALLATION
1. Install the boot band.
2. Wrap a plastic tape around the spline part on the
centre propeller shaft and then install the LJ boot.
PROPELLER SHAFT
PROPELLER SHAFT
25-8
>>B<< LJ ASSEMBLY INSTALLATION
AC101277AC
Outer race
Circlip
Cage
Inner
race
1. Apply a thin coat of the specified grease to the
ball grooves of the inner and outer races.
Specified grease: Repair kit grease
2. Assemble the LJ assembly as follows:
(1) Assemble the outer race, cage, balls, and
inner race with their mating marks aligned.
(2) Install the circlip.
AC101278 AC
3. Apply specified grease to the LJ assembly.
Specified grease: Repair kit grease
Amount to use: 75
± 5 g
AC101279
Rubber packing
LJ assembly
AE
4. Apply a thin coat of specified adhesive to the
groove side of LJ assembly (shown by arrows in
the figure) and install the rubber packing.
Specified adhesive: 3M Stud Locking 4170 or
equivalent
5. Set the groove side of LJ assembly (for packing)
toward the LJ boot side and install them.
AC101280
Socket wrench
AC
6. Lining up the mating marks on the LJ assembly
and the centre propeller shaft and using the
socket wrench, install the LJ assembly to the
centre propeller shaft.
AC101281
Bolt
LJ boot
AE
7. Using the bolt, align the bolt holes of the LJ boot
and the LJ assembly and install LJ boot to the LJ
assembly.
8. Install the rubber packing of the companion flange
side in the same manner as described in (4)
above.
>>C<< BOOT BAND INSTALLATION
CAUTION
•
AC107071AB
Vent plug
Mark
Boot
Clamp the boot by holding down the lever at a
position nearly opposite to the vent groove
provided in the LJ boot (at arrow marked
position on boot).
• Be sure to remove grease, if present, from
around the vent groove. Grease obstructs the
ventilation air passage.
PROPELLER SHAFT
PROPELLER SHAFT
25-9
>>D<< CENTRE BEARING
ASSEMBLY/COMPANION
FLANGE/SELF-LOCKING NUT
INSTALLATION
AC101283 AD
Companion flange
Self-locking
nut
Centre bearing
assembly
1. Set the centre bearing assembly in the direction
shown in the figure and install it to the centre
propeller shaft.
2. Install, lining up the mating marks on the
companion flange and the centre propeller shaft.
3. While tightening the self-locking nut, install the
centre bearing assembly with the companion
flange.
>>E<<CENTRE BEARING
ASSEMBLY/COMPANION
FLANGE/SELF-LOCKING NUT
INSTALLATION
AC101284
Rubber
mount
Dust seal
Companion
flange
Self-
locking
nut
AE
1. Set the centre bearing assembly in the direction
shown in the figure and install it to the centre
propeller shaft.
2. Align the mating marks on the companion flange
and the centre propeller shaft.
3. While tightening the self-locking nut, install the
centre bearing assembly with the companion
flange.
NOTES
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст