Mitsubishi Lancer Evolution IX. Manual — part 185

ON-VEHICLE SERVICE

SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR

54B-303

Function

Configuration procedure

Keyless entry system hazard
answerback function

When the lock button of the transmitter is pressed twice continuously within
two seconds, the hazard answerback function during the lock state will be
switched between available or unavailable.

• Function available: Buzzer sounds once. (Initial state)

• Function not available: Buzzer sounds twice.

When the unlock button of the transmitter is pressed twice continuously
within two seconds, the hazard answerback function during the unlock
state will be switched between available or unavailable.

• Function available: Buzzer sounds once. (Initial state)

• Function not available: Buzzer sounds twice.

Vehicle speed-dependent
wiper function

When the windshield wiper mist switch is turned ON for more than two
seconds, the vehicle speed-dependent wiper function is switched between
available or unavailable.

• Function available: Buzzer sounds once. (Initial state)

• Function not available: Buzzer sounds twice.

Headlamp
automatic-shutdown function

When the passing switch is turned ON for more than two seconds with the
head lamp switch ON and the turn signal lamp switch turned to RH, the
headlamp automatic-shutdown function is switched between available or
unavailable.

• Function available: Buzzer sounds once. (Initial state)

• Function not available: Buzzer sounds twice.

Interior lamp
automatic-shutdown function

When the hazard switch is turned ON for more than two seconds, the
interior lamp automatic-shutdown function is switched between available or
unavailable.

• Function available: Buzzer sounds once. (Initial state)

• Function not available: Buzzer sounds twice.

Delayed lamp-off time of the
interior lamp

When the turn signal lamp switch is set in the order of RH to LH to RH to
LH within three seconds from the LH position, the delayed lamp-off time
switches (Returns to a after e, and repeats from a in order).

a. 15 seconds: Buzzer sounds four times. (Initial state)
b. 7.5 seconds: Buzzer sounds five times.
c. 30 seconds: Buzzer sounds once.
d. 10 seconds: Buzzer sounds twice.
e. 0 seconds (No delay time): Buzzer sounds three times.

Initialisation of all functions

When the windshield washer switch is ON for more than 20 seconds
continuously, the buzzer sounds twice, and all functions will be initialised
(Settings are returned to their initial states). The configuration mode entry
buzzer sounds after 10 seconds, however to initialise all functions, the ON
state should be continued for 20 seconds. When the windshield washer
switch is ON for more than 20 seconds continuously without the
configuration mode set, the configuration mode will be set after 10 seconds
without the initialisation of all functions.

NOTES

54C-1

GROUP 54C

SMART WIRING

SYSTEM (SWS)

USING SWS

MONITOR

CONTENTS

GENERAL INFORMATION . . . . . . . .

54C-2

SPECIAL TOOLS. . . . . . . . . . . . . . . .

54C-2

TROUBLESHOOTING . . . . . . . . . . . .

54C-4

PRIOR TO TROUBLESHOOTING . . . . . . .

54C-4

STANDARD FLOW OF DIAGNOSTIC
TROUBLESHOOTING . . . . . . . . . . . . . . . .

54C-4

HOW TO CONNECT THE SWS MONITOR

54C-5

ECU CHECK . . . . . . . . . . . . . . . . . . . . . . . .

54C-10

DATA LIST CHECK . . . . . . . . . . . . . . . . . .

54C-11

PULSE CHECK. . . . . . . . . . . . . . . . . . . . . .

54C-19

M.U.T.-II/III DRIVE RECORDER FUNCTION

54C-20

TROUBLE SYMPTOM CHART . . . . .

54C-20

CHECK TROUBLE BY USING THE

INPUT SIGNAL CHECK. . . . . . . . . . .

54C-24

OPERATION AND FUNCTION
QUICK-REFERENCE TABLE FOR

INPUT SIGNAL INSPECTION

PROCEDURES . . . . . . . . . . . . . . . . . .

54C-25

SYMPTOM PROCEDURES . . . . . . . .

54C-26

BUZZER . . . . . . . . . . . . . . . . . . . . . . . . . . .

54C-57

CENTRAL DOOR LOCKING SYSTEM . . . .

54C-59

POWER WINDOW . . . . . . . . . . . . . . . . . . .

54C-86

KEYLESS ENTRY SYSTEM . . . . . . . . . . . .

54C-137

WINDSHIELD WIPER AND WASHER . . . .

54C-142

IGNITION KEY CYLINDER ILLUMINATION

LAMP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

54C-169

HEADLAMP AND TAIL LAMP. . . . . . . . . . .

54C-173

FLASHER TIMER . . . . . . . . . . . . . . . . . . . .

54C-208

FOG LAMP . . . . . . . . . . . . . . . . . . . . . . . . .

54C-231

INTERIOR LAMP. . . . . . . . . . . . . . . . . . . . .

54C-244

INPUT SIGNAL PROCEDURES. . . . .

54C-258

CHECK AT ECU TERMINAL . . . . . . .

54C-316

GENERAL INFORMATION

SMART WIRING SYSTEM (SWS) USING SWS MONITOR

54C-2

GENERAL INFORMATION

M1549000100555

For the general information regarding the SWS, refer
to GROUP 54B

− General Information

P.54B-2

.

SPECIAL TOOLS

M1549000300786

Tool

Number

Name

Use

MB991502

M.U.T.-II
sub-assembly

Check the SWS (ECU check and
service data)

MB991955

A: MB991824
B: MB991827
C: MB991910
D: MB991911
E: MB991825
F: MB991826

M.U.T.-III
sub-assembly

A: Vehicle

communication
interface (V.C.I.)

B: M.U.T.-III USB

cable

C: M.U.T.-III main

harness A
(Vehicles with CAN
communication
system)

D: M.U.T.-III main

harness B
(Vehicles without
CAN
communication
system)

E: M.U.T.-III

measurement
adapter

F: M.U.T.-III trigger

harness

SWS communication line check
(ECU check and service data)

CAUTION

M.U.T.-III main harness B
(MB991911) should be used.
M.U.T.-III main harness A
should not be used for this
vehicle.

B991502

MB991910

MB991826

MB991955

MB991911

MB991824

MB991827

MB991825

A

B

C

D

E

F

DO NOT USE