Lincoln Corsair (2022 year). Manual in english — page 4

What do I do if my phone is lost, damaged,
or the battery has depleted?

Use the Backup Start Passcode that you
created to protect you in the event that
you lose your phone, damage it, or the
battery depletes. See Using the
Backup Start Passcode (page 70).

How many phones can I use for Phone as
a Key?

You can program and activate up to four
phones with Phone as a Key to your
vehicle.

How does a valet drive my car if I only use
my Phone as a Key?

Have the valet use the temporary valet
passcode that you created when using
valet mode. See Using the Valet Mode
(page 70).

I uninstalled my Lincoln Way app and
reinstalled it. Why am I not able to get a
new Phone as a Key?

Remove the Phone as a Key that was
previously associated with your phone
or reset Phone as a Key from your
vehicle, and then request a new Phone
as a Key. See Programming Your
Phone (page 69).

Why can I not remotely start the vehicle
with my Phone as a Key?

Using the Lincoln Way app, verify your
Phone as a Key setup is complete and
enabled via Bluetooth connection on at
least one phone. If Bluetooth has
connected but Phone as a Key setup is
not complete, complete the setup of
your Phone as a Key, as prompted from
the Lincoln Way app. See Programming
Your Phone (page 69).

72

Phone as a Key

(If Equipped)

WHAT IS MYKEY

MyKey allows you to program keys with
restricted driving modes to promote good
driving habits.

MYKEY SETTINGS

NON-CONFIGURABLE MYKEY
SETTINGS

Seatbelt Reminder or Belt-Minder™

MyKey mutes the audio system until the
drivers, and in some instances, passengers,
fasten their seatbelts.

Note: If your vehicle includes an AM/FM
radio or a very basic audio system, then the
radio may not mute.

Satellite Radio

(If Equipped)

Satellite radio adult content restrictions.

Early Low Fuel

The low fuel level warning lamp turns on
earlier.

Driving and Parking Aids

Parking aids, blind spot information system
and cross traffic alert turn on when you start
the engine and cannot be switched off with
a MyKey.

Pre-collision assist and lane keeping alert
turn on when you start the engine, but can
be switched off with a MyKey.

A new destination in the navigation system
can only be set using voice commands when
using a MyKey, and with your vehicle moving.

Note: MyKey drivers may be able to turn the
lane departure warning feature off, but this
feature turns back on automatically with
every new key cycle.

CONFIGURABLE MYKEY SETTINGS

You can configure the following settings after
creating a MyKey. See Creating a MyKey
(page 74).

Speed Limit

WARNING: Do not set MyKey

maximum speed limit to a limit that will
prevent the driver from maintaining a safe
speed considering posted speed limits and
prevailing road conditions. The driver is
always responsible to drive in accordance
with local laws and prevailing conditions.
Failure to do so could result in accident or
injury.

You can set a speed limit for your vehicle.
Warning messages appear in the information
display and a tone sounds if your vehicle
reaches the set speed. You cannot override
the set speed when using a MyKey.

Speed Reminder

You can set a speed reminder for your
vehicle. Warning messages appear in the
information display and a tone sounds if your
vehicle exceeds the set speed.

73

MyKey™

Audio System Volume Limit

The audio system maximum volume is
reduced. A message appears in the
information display if you attempt to exceed
the volume limit. Automatic volume control
turns off.

Emergency Assistance

If you set emergency assistance to always
on, you cannot switch it off with a MyKey.

Do Not Disturb

If you set do not disturb to always on, you
cannot switch it off with a MyKey.

Note: If a phone is connected using Apple
CarPlay or Android Auto while driving with
a MyKey, the driver can receive phone calls
and text messages even if the do not disturb
restriction is on. If the vehicle comes with
satellite radio, the adult content is not
restricted.

Traction Control

If you set traction control to always on, you
cannot switch it off with a MyKey.

CREATING A MYKEY

E306288

1. Open the center console lid.

2. Place the passive key in the position

shown.

3. Switch the ignition on.

4. Press Settings on the touchscreen.
5. Press Vehicle Settings.

6. Press MyKey.

7. Press Create MyKey.

8. Press Yes.

9. Switch the ignition off.

Note: We recommend that you label this key.

PROGRAMMING A MYKEY

You can only program each MyKey to the
same settings.

1. Switch the ignition on using an admin

key.

2. Using the touchscreen, press Menu.
3. Press Settings.

4. Press Vehicle.

5. Press MyKey.

6. Press a setting.

7. Configure the setting.

8. Switch the ignition off.

CLEARING ALL MYKEYS

When you clear all MyKeys, you remove all
restrictions and return all MyKeys to their
original admin key status.

1. Switch the ignition on using an admin

key.

74

MyKey™

2. Using your touchscreen, press Menu.

3. Press Settings.
4. Press Vehicle.

5. Press MyKey.

6. Press Clearing All MyKeys.

7. Press Yes to clear all MyKeys from your

vehicle.

CHECKING MYKEY SYSTEM
STATUS

You can find information about the distance
traveled using a MyKey, and the number of
admin keys and MyKeys created for your
vehicle.

1. Switch the ignition on.

2. Press Settings on the touchscreen.

3. Press Vehicle Settings.

4. Press MyKey.

5. Press MyKey Information.
6. Switch the ignition off.

USING MYKEY WITH REMOTE
START SYSTEMS

MyKey is not compatible with unapproved,
aftermarket remote start systems. If you
choose to install a remote start system, see
an authorized dealer for an approved remote
start system.

MYKEY – TROUBLESHOOTING

MYKEY – INFORMATION MESSAGES

Description

Message

Displays when trying to create a MyKey and there is no admin key in the backup position. See
Creating a MyKey (page 74).

Place Key in Backup Location

Displays when trying to create a MyKey with a key already designated as a MyKey.

Key is Already a MyKey

Displays to confirm that you have a restricted key after you switch the ignition off.

This Key restricted at Next Key Cycle.
Label Key as MyKey

75

MyKey™

MYKEY – FREQUENTLY ASKED
QUESTIONS

What is an admin key?

•

An admin key is a key that you have not
created as a MyKey. See Creating a
MyKey (page 74).

Why am I not able create a MyKey?

•

You did not place the admin key in the
backup position. See Creating a MyKey
(page 74).

•

You did not use an admin key to switch
the ignition on.

•

The key used to switch the ignition on is
the only admin key. At least one key
needs to remain as an admin key.

•

You did not switch the ignition off after
creating the last MyKey.

Why am I not able to program a
MyKey?

•

The admin key is not inside your vehicle.

•

The key used to switch the ignition on is
not an admin key.

•

You have not created any MyKeys. See
Creating a MyKey (page 74).

Why am I not able to clear the MyKeys?

•

The admin key is not inside your vehicle.

•

The key used to switch the ignition on is
not an admin key.

•

You have not created any MyKeys. See
Creating a MyKey (page 74).

Why is the MyKey distance not
accumulating?

•

The key used to start the engine is an
admin key.

•

An admin key and a MyKey are inside
your vehicle.

•

You have not created any MyKeys. See
Creating a MyKey (page 74).

•

You have cleared the MyKeys.

Why am I not able to start the engine
with a MyKey?

•

An admin key and a MyKey are inside
your vehicle.

76

MyKey™

LOCKING AND UNLOCKING

You can use the power door lock or the
remote control to lock and unlock your
vehicle.

Note: Do not use the door latch assembly
to attach any accessory, such as handles or
steps, as this can cause damage to your
vehicle.

Power Door Locks

The power door lock is on the driver and
front passenger door panels.

E309203

Unlock.

A

Lock.

B

Door Lock Indicator

An LED on each door window trim lights
when you lock the door. It remains on for up
to five minutes after you switch the ignition
off.

Switch Inhibitor

When you electronically lock your vehicle,
the power door lock and interior luggage
compartment release switch no longer
operates after 20 seconds. Make sure you
unlock your vehicle with the remote control,
intelligent access or keyless keypad, or
switch the ignition on, to restore function to
these switches. You can switch this feature
on or off from the touchscreen. See Settings
(page 555).

Remote Control

You can use the remote control at any time.
The luggage compartment release button
only works when your vehicle speed is less
than 3 mph (5 km/h).

Unlocking the Doors (Two-Stage Unlock)

E138629

Press the button to unlock the
driver door. Press the button again
within three seconds to unlock all

doors. The turn signals flash.

77

Doors and Locks

Press and hold both the lock and unlock
buttons on the remote control for four
seconds to disable or enable two-stage
unlocking. Disabling two-stage unlocking
allows all vehicle doors to unlock with one
press of the button. The turn signals flash
twice to indicate a change to the unlocking
mode. The unlocking mode applies to the
remote control, keyless entry keypad and
intelligent access.

Intelligent access at the driver door unlocks
all doors when you disable two-stage
unlocking.

Locking the Doors

E138623

Press the button to lock all the
doors. The turn signals flash.

Press the button again within three

seconds to confirm that all the doors have
closed. The doors lock again, a tone sounds
and the turn signals flash if all the doors and
the luggage compartment have closed.

Mislock

If any door or the luggage compartment is
open, or if the hood is open on vehicles with
an anti-theft alarm or remote start, a tone
sounds and the turn signals do not flash. You
can switch this feature on or off from the
touchscreen. See Settings (page 555).

Audible and Visual Locking Confirmation

If audible and visual locking confirmation is
configurable, you can turn it on or off from
the touchscreen. See Settings (page 555).

Mechanical Key

The intelligent access key also contains a
removable key blade that you can use to lock
and unlock your vehicle. See Remote
Control (page 65).

Turn the top of the key toward the front of
your vehicle once to lock all doors.

Turn the top of the key toward the rear of
your vehicle once to unlock the driver door
only.

Locking and Unlocking the Doors with the
Key Blade

If the central locking function does not
operate, lock the doors using the key blade
in the door handle lock cylinder.

E310901

Locking with the Key Blade

Insert the key blade into the driver door
handle lock cylinder, turn the key up toward
the front of your vehicle to lock.

Unlocking with the Key Blade

Insert the key blade into the driver door
handle lock cylinder and turn the key down
toward the rear of your vehicle to unlock.

78

Doors and Locks

Opening a Rear Door from Inside

Pull the interior door handle twice to unlock
and open a rear door. The first pull unlocks
the door and the second pull unlatches the
door.

Activating Intelligent Access

General Information

You can unlock and lock the vehicle without
taking the keys out of your pocket or purse
when your intelligent access key is within
3 ft (1 m) of your vehicle. Intelligent access
uses a sensor on the back of the door handle
for unlocking, and a separate sensor on the
face of each door handle for locking.

The system does not function if:
•

Your vehicle battery has no charge.

•

The key battery has no charge.

•

The key frequencies have jammed.

Note: The system may not function if the
intelligent access key is close to metal
objects or electronic devices, for example,
keys or a cell phone.

Note: If the system does not function, use
the key blade to lock and unlock your
vehicle. See Remote Control (page 65).

Unlocking Using Intelligent Access

E248553

With your intelligent access key within 3 ft
(1 m) of your vehicle, touch the unlock sensor
on the back of the door handle for a brief
period and then pull on the door handle to
unlock, being careful not to touch the lock
sensor at the same time or pull on the door
handle too quickly. The intelligent access
system requires a brief delay to authenticate
your intelligent access key.

Locking Using Intelligent Access

E248554

With your intelligent access key within 3 ft
(1 m) of your vehicle, touch the outer door
handle lock sensor for approximately one
second to lock, being careful not to touch
the unlock sensor on the back of the door
handle at the same time. After locking, you
can immediately pull on the door handle to
confirm locking occurred without
inadvertently unlocking.

At the Liftgate

Press the exterior liftgate release button
inside the top of the liftgate pull-cup handle.

Smart Unlocks

This feature helps to prevent you from
unintentionally locking your intelligent access
key inside the passenger compartment or
rear cargo area.

When you lock your vehicle with the door
open and the ignition off, your vehicle
searches for an intelligent access key in the
passenger compartment after you close the
door. If your vehicle finds a key, all the doors
immediately unlock.

79

Doors and Locks

You can override the smart unlock feature
and intentionally lock the intelligent access
key inside your vehicle. To do this, lock your
vehicle after you have closed all the doors
by:
•

Using the keyless entry keypad.

•

Pressing the lock button on another
intelligent access key.

•

Touching the locking area on the handle
with another intelligent access key in
your hand.

When you open one of the front doors with
the ignition on, and lock your vehicle using
the power door lock, all doors lock, then
unlock.

Autolock

(If Equipped)

Autolock locks all the doors when all of the
following occur:
•

You have closed all doors.

•

The ignition is on.

•

You shift into any gear putting your
vehicle in motion.

•

Your vehicle reaches a speed greater
than 12 mph (20 km/h).

Autolock repeats when:
•

You open, then close any door while the
ignition is on and your vehicle speed is
9 mph (15 km/h) or lower.

•

Your vehicle reaches a speed greater
than 12 mph (20 km/h).

Autounlock

(If Equipped)

Autounlock unlocks all the doors when:
•

The ignition is on, you have closed all the
doors, and your vehicle has been moving
at a speed greater than 12 mph (20 km/h).

•

Your vehicle comes to a stop and you
switch the ignition off or to the accessory
position.

•

You open the driver door within 10
minutes of switching the ignition off or to
accessory.

Note: The doors do not autounlock if you
electronically lock your vehicle after you
switch the ignition off before you open the
driver door.

Enabling or Disabling

You can enable or disable the feature from
the touchscreen or an authorized dealer can
do it for you, See Settings (page 555).

Illuminated Entry

(If Equipped)

The interior lamps and select exterior lamps
light when you unlock the doors with the
remote control.

The system turns off the lights if:
•

You start your vehicle.

•

You press the remote control lock button.

•

They are on for 25 seconds.

The lights do not turn off if:
•

You switch them on with the lamp
control.

•

Any door is open.

Illuminated Exit

The interior lamps and select exterior lamps
light when you have closed all the doors and
you switch the ignition off.

80

Doors and Locks

The lamps turn off if all the doors remain
closed and either of the following occurs:
•

After 25 seconds elapse.

•

You lock your vehicle from the outside.

Battery Saver

If you leave the courtesy lamps or dome
lamps on and switch the ignition off, this
feature turns them off after some time.

Accessory Mode Battery Saver for
Intelligent Access Keys

If you leave your vehicle with the ignition on,
it turns off 30 minutes after you close all the
doors.

Welcome Lighting

This feature lights select exterior lighting as
you approach your vehicle. You must have
an intelligent access key with you. The
feature turns off when you open a door,
liftgate, or unlock your vehicle. Welcome
lighting remains on for 25 seconds or until
you start your vehicle.

The feature is active when:
•

You configure the feature from the
touchscreen. See Welcome Lighting
(page 110).

•

The ignition is off.

•

You have closed all the doors and
liftgate.

•

You lock your vehicle.

The feature disables when:
•

Your vehicle detects the intelligent
access key is inside.

•

The intelligent access key is in close
range of the vehicle for more than two
minutes.

•

The anti-theft alarm triggers.

•

You do not start your vehicle for more
than five days.

•

The vehicle battery charge is low.

•

You approach the vehicle to trigger the
welcome lighting feature 10 or more
times without switching the ignition on.

Note: When this feature disables, you must
switch the ignition on to reset it.

Note: This feature may not correctly operate
if you store the intelligent access key within
8–15 ft (2.4–4.6 m) of your vehicle while not
in use.

Note: Welcome Lighting does not function
if you disable it from the touchscreen.

81

Doors and Locks

KEYLESS ENTRY LIMITATIONS

Make sure your remote control is within 3 ft
(1 m) from the front door handles and the
tailgate.

The system could not function if:
•

The remote control remains stationary
for about a minute.

•

The vehicle battery has no charge.

•

The remote control battery has no
charge.

•

There is interference causing issues with
the remote control frequencies.

•

The remote control is too close to metal
objects or electronic devices, for example
keys or a cell phone.

KEYLESS ENTRY SETTINGS

Switching Keyless Entry On and Off

1. Switch the ignition on using an original

key that has not been created as a
MyKey.

2. Press Settings on the touchscreen.

3. Press Vehicle Settings.
4. Press Locks.

Reprogramming the Unlocking
Function

You can enable two-stage unlocking function
allowing you to unlock only the driver door
when you touch the unlock sensor.

Press and hold both the lock and unlock
buttons on the remote control for four
seconds to disable or enable two-stage
unlocking.

If you program the unlocking function so that
only the driver door unlocks, you can unlock
all of the other doors from inside your vehicle
using the power door lock control. You can
unlock individual doors by pulling the interior
door handles on those doors.

USING KEYLESS ENTRY

Unlocking the Doors

E248553

With the remote control within 3 ft (1 m) of
your vehicle, touch the unlock sensor on the
back of the door handle for a brief period
and then pull on the door handle to unlock,
being careful not to touch the lock sensor at
the same time or pull on the door handle too
quickly. The system requires a brief delay to
authenticate the remote control.

Locking the Doors

E248554

82

Keyless Entry

With your passive key within 3 ft (1 m) of your
vehicle, touch the outer door handle lock
sensor for approximately one second to lock,
being careful not to touch the unlock sensor
on the back of the door handle at the same
time. After locking, you can immediately pull
on the door handle to confirm locking
occurred without inadvertently unlocking.

Opening the Liftgate with the Remote
Control

E291416

Press the exterior liftgate release button
inside of the liftgate handle. The liftgate
unlocks and opens. See Opening the
Liftgate From Outside Your Vehicle (page
88).

KEYLESS ENTRY –
TROUBLESHOOTING

KEYLESS ENTRY – FREQUENTLY
ASKED QUESTIONS

Why does the keypad not accept the access
code?

If you enter the access code too fast on
the keypad, the unlock function may not
work. Slowly re-enter the access code.

Why does the passive key not work?

The system deactivates passive keys
left inside your vehicle when you lock
it. You cannot switch the ignition on
using a deactivated passive key. Press
the unlock button on the remote control
to reactivate a passive key.

Why does the keypad not function?

The keypad goes into an anti-scan
mode if you enter a wrong code seven
times. The anti-scan mode disables the
keypad for one minute and the red light
flashes.

83

Keyless Entry

WHAT IS THE KEYLESS ENTRY
KEYPAD

The keyless entry keypad allows you to lock
and unlock your vehicle using the keypad
on the window trim.

KEYLESS ENTRY KEYPAD
LIMITATIONS

The system may not function if:
•

The vehicle battery has no charge.

LOCATING THE KEYLESS ENTRY
KEYPAD

The keypad is near the driver window and
illuminates when you touch it.

E138637

KEYLESS ENTRY KEYPAD MASTER
ACCESS CODE

Unlocking the Doors

E138637

Enter the factory-set five-digit code or your
personal code. You must press each number
within five seconds of each other.

•

Press 3-4 within five seconds to unlock
all doors.

84

Keyless Entry Keypad

Locking the Doors

E138637

Press and hold 7·8 and 9·0 at the same time
with the driver door closed.

Note: You do not need to enter the code
first.

KEYLESS ENTRY KEYPAD
PERSONAL ACCESS CODES

Programming a Personal Entry Code

1. Enter the five-digit master code.

2. Press 1·2 on the keypad within five

seconds.

3. Enter your personal five-digit code. You

must do this within five seconds of
completing Step 2.

4. Press 1·2 on the keypad to save personal

code 1.

The doors lock then unlock to confirm that
programming was successful.

To program additional personal entry codes,
repeat Steps 1 through 3, then for Step 4:
•

Press 3·4 to save personal code 2.

•

Press 5·6 to save personal code 3.

•

Press 7·8 to save personal code 4.

•

Press 9·0 to save personal code 5.

If your vehicle comes with SYNC, you can
also program the system with a personal
entry code.

Hints:
•

Do not set a code that uses five of the
same number.

•

Do not use five numbers in sequential
order.

•

The five-digit master code works even if
you have set your own personal code.

Erasing a Personal Code

1. Enter the five-digit master code.

2. Press and release 1·2 on the keypad

within five seconds.

3. Press and hold 1·2 for two seconds. You

must do this within five seconds of
completing Step 2.

All personal codes erase and only the
five-digit master code works.

Anti-Scan Feature

The keypad goes into an anti-scan mode if
you enter the wrong code seven times. This
mode turns off the keypad for one minute
and the keypad lamp flashes.

85

Keyless Entry Keypad

The anti-scan feature turns off after:
•

One minute of keypad inactivity.

•

You press the unlock button on the
remote control.

•

You switch the ignition on.

•

You unlock your vehicle using keyless
entry.

USING THE KEYLESS ENTRY
KEYPAD

Unlocking the Doors

E138637

Enter the factory-set five-digit code or your
personal code. You must press each number
within five seconds of each other.

•

Press 3-4 within five seconds to unlock
all doors.

Locking the Doors

E138637

Press and hold 7·8 and 9·0 at the same time
with the driver door closed.

Note: You do not need to enter the code
first.

86

Keyless Entry Keypad

KEYLESS ENTRY KEYPAD –
TROUBLESHOOTING

KEYLESS ENTRY KEYPAD –
FREQUENTLY ASKED QUESTIONS

Why does the keypad not accept the access
code?

If you enter the access code too fast on
the keypad, the unlock function may not
work. Slowly re-enter the access code.

Why does the keypad not function?

The keypad goes into an anti-scan
mode if you enter a wrong code seven
times. The anti-scan mode disables the
keypad for one minute and the red light
flashes.

87

Keyless Entry Keypad