Dodge Ram. Manual — part 104
Symptom:
*HVAC SYSTEM TEST
POSSIBLE CAUSES
ATTEMPT TO COMMUNICATE WITH THE PCM
CHECK FOR HVAC RELATED DTCS IN THE PCM
CHECK FOR ACTIVE HVAC DTCS AND SYSTEM TEST FAULT MESSAGES
CHECK FOR HVAC RELATED DTCS IN THE PCM
MANUAL A/C SYSTEM TEST
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t, attempt to communicate with the Powertrain Control Module
(PCM).
Was the DRBIII
t able to communicate with the PCM?
All
Yes
→ Go To 2
No
→ Refer to the communication category for the related symptom(s).
Perform BODY VERIFICATION TEST - VER 1.
2
With the DRBIII
t, read Powertrain Computer DTCs.
Are any HVAC related DTCs present?
All
Yes
→ Refer to the Powertrain Diagnostic Procedures Manual for the
related symptom(s).
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 3
413
HEATING & A/C
TEST
ACTION
APPLICABILITY
3
NOTE: Active DTCs must be resolved before diagnosing stored DTCs.
NOTE: Anytime a DTC becomes active, or a Cooldown Test fault message,
Actuator Circuit Test fault message, or Door Recalibration fault message is
displayed, proceed to the conclusion question.
Turn the ignition on.
Turn the mode select control to the panel position.
Verify that the blower motor operates correctly in all speeds. Diagnose and repair all
blower related faults before proceeding with this test.
For vehicles that are not equipped with A/C, skip the next 6 steps of this procedure.
Turn the blower control to the low speed position.
Make sure that the A/C switch is turned off (status indicator not illuminated).
Turn the blower control to the off position.
Start the engine.
Turn the blower control to the high speed position.
CAUTION: The evaporator temperature must be above 12.7°C (55°F) and the
work area ambient temperature must be above 21.1°C (70°F) to test A/C
system operation.
With the DRBIII
t in HVAC, System Tests, actuate the AC Cooldown Test. Allow one
minute for test to complete.
If not done previously, start the engine.
Turn the blower control to the low speed position.
Set the blend/driver blend (dual-zone) control to the full cold position.
If equipped, set the passenger blend control to the full cold position.
Monitor the DRBIII
t for active HVAC DTCs during the following test steps.
If equipped, press the A/C switch on, wait 30 seconds, and then press it off.
On Dual-Zone systems, press the MAX switch on, wait 30 seconds, and then press it
off.
If equipped, press the EBL switch on, wait 30 seconds, and then press it off.
Move the blend/driver blend (dual-zone) control from full cold to full hot, wait 30
seconds, and then move it back to full cold.
If equipped, move the passenger blend control from full cold to full hot, wait 30
seconds, and then moved it back to full cold.
Turn the mode select control to the defrost position, wait 30 seconds, and then turn
it to the panel position (dual-zone) or MAX panel position (single-zone).
With the DRBIII
t in HVAC, System Tests, actuate the Actuator Circuit Test.
With the DRBIII
t in HVAC, System Tests, actuate the HVAC Door Recalibration
Test.
Does the DRBIII
t display any HVAC DTCs or System Test fault messages?
All
Yes
→ Return to the symptom list and choose the symptom(s).
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 4
4
With the DRBIII
t, read PCM DTCs.
Are any HVAC related DTCs present?
All
Yes
→ Refer to the Powertrain Diagnostic Procedures Manual for the
related symptom(s).
Perform BODY VERIFICATION TEST - VER 1.
No
→ Recheck the climate control system performance. Refer to Service
Information for additional information.
Perform BODY VERIFICATION TEST - VER 1.
414
HEATING & A/C
*HVAC SYSTEM TEST —
Continued
Symptom:
BATTERY 1 VOLTAGE OPEN
POSSIBLE CAUSES
CHECK FUSE #13
OPEN FUSED B+ CIRCUITS
FRONT CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
NOTE: This DTC must be active to perform this test. If DTC is stored, erase
DTC and check for an intermittent condition.
Turn the ignition off.
Check fuse #13 in the IPM.
Is the fuse open?
All
Yes
→ Replace the fuse.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 2
2
Turn the ignition off.
Remove the Front Control Module from the IPM.
Using a 12-volt test light connected to ground, probe both Fused B+ circuits (cavs 3
and 4).
Is the test light illuminated for both circuits?
All
Yes
→ Replace the Front Control Module in accordance with the service
information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Power Distribution Center (PDC) in accordance with
the service information.
Perform BODY VERIFICATION TEST - VER 1.
415
IGNITION, POWER, ACCESSORY
Symptom:
BATTERY 2 VOLTAGE OPEN
POSSIBLE CAUSES
CHECK FUSE #11
OPEN FUSED B+ CIRCUITS
FRONT CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
NOTE: This DTC must be active to perform this test. If DTC is stored, erase
DTC and check for an intermittent condition.
Turn the ignition off.
Check fuse #11 in the IPM.
Is the fuse open?
All
Yes
→ Replace the fuse.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 2
2
Turn the ignition off.
Remove the Front Control Module from the IPM.
Using a 12-volt test light connected to ground, probe both Fused B+ circuits (cavs 6
and 7).
Is the test light illuminated for both circuits?
All
Yes
→ Replace the Front Control Module in accordance with the service
information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Power Distribution Center (PDC) in accordance with
the service information.
Perform BODY VERIFICATION TEST - VER 1.
416
IGNITION, POWER, ACCESSORY
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст