Dodge Ram. Manual — part 32
TEST
ACTION
APPLICABILITY
3
Is this vehicle equipped with a Passenger Airbag On - Off Switch?
All
Yes
→ Go To 4
No
→ With the DRBIIIt in MISCELLANEOUS, read the Configure for
Airbag ON - OFF Switch current status. Enter the number 1 and
press enter to re configure the ACM for NO AIRBAG ON/OFF
SWITCH.
Perform __AIRBAG VERIFICATION TEST - VER 1.
4
Gain access to the Passenger Airbag On - Off Switch connector.
Is the Passenger Airbag On - Off Switch connected to the dash harness?
All
Yes
→ Go To 5
No
→ Connect the Passenger Airbag On - Off switch to the dash harness
connector.
Perform __AIRBAG VERIFICATION TEST - VER 1.
5
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN IGNITION
OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BEFORE
PROCEEDING.
Disconnect the Passenger On - Off Switch connector.
NOTE: Check connectors - Clean and repair as necessary.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN IGNITION
ON, THEN RECONNECT THE BATTERY.
Measure the voltage on the Fused Ignition Switch Output Run - Start circuit between
the PAB On - Off Switch connector and ground.
Is the voltage above 10.0 volts?
All
Yes
→ Go To 6
No
→ Repair the open Fused ignition Switch Output Run - Start circuit.
Perform __AIRBAG VERIFICATION TEST - VER 1.
6
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
Disconnect the Passenger Airbag On - Off Switch.
NOTE: Check connectors - Clean and repair as necessary.
Measure the resistance between PAB On - Off Switch terminals 3 and 4.
Is the resistance approximately 14 ohms?
All
Yes
→ Go To 7
No
→ Replace the Passenger Airbag ON - OFF Switch in accordance
with the service information.
Perform __AIRBAG VERIFICATION TEST - VER 1.
125
AIRBAG
PASSENGER OFF INDICATOR CIRCUIT SHORT TO GROUND —
Continued
TEST
ACTION
APPLICABILITY
7
Disconnect the Airbag Control Module connector
NOTE: Check connectors - Clean and repair as necessary.
WARNING: IF THE AIRBAG CONTROL MODULE IS DROPPED AT ANY
TIME, IT MUST BE REPLACED. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND PERSONAL INJURY OR DEATH.
Connect the appropriate Load Tool ACM Adaptor to the Airbag Control Module
connector(s).
Measure the resistance of the PAB Indicator Driver circuit between the ACM and the
PAB On - Off Switch connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 8
No
→ Repair the open Passenger Airbag Indicator Driver circuit.
Perform __AIRBAG VERIFICATION TEST - VER 1.
8
Measure the resistance of the PAB Indicator Driver circuit between the PAB On - Off
Switch connector and ground.
Is the resistance below 10K ohms?
All
Yes
→ Repair the Passenger Airbag Indicator Driver circuit short to
ground.
Perform __AIRBAG VERIFICATION TEST - VER 1.
No
→ Go To 9
9
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
Reconnect the PAB Indicator connector.
WARNING: IF THE AIRBAG CONTROL MODULE IS DROPPED AT ANY
TIME, IT MUST BE REPLACED. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND PERSONAL INJURY OR DEATH.
If there are no possible causes remaining, view repair.
All
Repair
Replace the Airbag Control Module in accordance with Service
Instructions.
Perform __AIRBAG VERIFICATION TEST - VER 1.
126
AIRBAG
PASSENGER OFF INDICATOR CIRCUIT SHORT TO GROUND —
Continued
TEST
ACTION
APPLICABILITY
10
With the DRBIII
t, record and erase all DTC’s from all Airbag modules.
If equipped with Passenger Airbag On - Off switch, read the DTC’s in all switch
positions.
If any ACTIVE codes are present they must be resolved before diagnosing any stored
codes.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Look for chaffed, pierced, pinched, or partially broken wires and broken, bent, pushed
out, spread, corroded, or contaminated terminals.
The following additional checks may assist you in identifying a possible intermittent
problem.
Reconnect any disconnected components and harness connector.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION ON, THEN RECONNECT THE BATTERY.
With the DRBIII
t monitor active codes as you work through the following steps.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, MAINTAIN A SAFE
DISTANCE FROM ALL AIRBAGS WHILE PERFORMING THE FOLLOWING
STEPS.
Wiggle the wiring harness and connectors of the related airbag circuit or component.
If codes are related to the Driver Airbag circuits, rotate the steering wheel from stop
to stop.
IF only stored codes return continue the test until the problem area has been isolated
In the previous steps you have attempted to recreate the conditions responsible for
setting active DTC in question.
Are any ACTIVE DTCs present?
All
Yes
→ Select appropriate symptom from Symptom List.
No
→ No problem found at this time. Erase all codes before returning
vehicle to customer.
127
AIRBAG
PASSENGER OFF INDICATOR CIRCUIT SHORT TO GROUND —
Continued
Symptom:
PASSENGER SEAT BELT TENSIONER CIRCUIT OPEN
When Monitored and Set Condition:
PASSENGER SEAT BELT TENSIONER CIRCUIT OPEN
When Monitored:
With the ignition on, the ACM monitors the resistance of the Passenger
Seat Belt Tensioner circuits.
Set Condition:
When the ACM detects an open circuit or high resistance in the Passenger
Seat Belt Tensioner circuits.
POSSIBLE CAUSES
PASSENGER SEAT BELT TENSIONER CIRCUIT OPEN
PASSENGER SEAT BELT TENSIONER LINE 1 OR LINE 2 CIRCUIT OPEN
ACM, PASSENGER SEAT BELT TENSIONER CIRCUIT OPEN
STORED CODE OR INTERMITTENT CONDITION
ACTIVE CODE PRESENT
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
NOTE: Ensure the battery is fully charged.
NOTE: For the purpose of this test, the AECM and ORC modules will be
referred to as an ACM.
SELECT ACTIVE or STORED DTC:
All
ACM - ACTIVE DTC
Go To
2
ACM - STORED DTC
Go To
5
NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.
2
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN IGNITION
OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BEFORE
PROCEEDING.
Disconnect the Passenger Seat Belt Tensioner connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the appropriate Load Tool to the Passenger Seat Belt Tensioner connector.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN IGNITION
ON, THEN RECONNECT THE BATTERY.
With the DRBIII
t, read the active Airbag Control Module DTC’s.
Does the DRBIII
t display PASSENGER SBT CIRCUIT OPEN?
All
Yes
→ Go To 3
No
→ Replace the Passenger Seat Belt Tensioner in accordance with the
Service Information.
Perform __AIRBAG VERIFICATION TEST - VER 1.
128
AIRBAG
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст