Dodge Dakota (ND). Manual — part 875
HOOK-TOW
REMOVAL
1. Remove the Front End Sheet Metal (FESM) mount-
ing bolt (3).
2. Remove the two lower fascia support nuts (1) and
remove the tow hook assembly (5).
3. Remove the nuts (3) and remove the brackets (1 &
2).
13 - 20
FRAME & BUMPERS
ND
INSTALLATION
1. Install the brackets (1 & 2) and install the nuts (3).
2. Tighten the nuts to 95 N·m (70 ft. lbs.)
3. Install the hook assembly (5) and install the FESM
bolt (3).
4. Install the fascia support nuts (1).
5. Tighten the FESM Bolt (3) to 75 N·m (55 ft. lbs.)
6. Tighten the fascia support nuts (1) to 94 N·m (70 ft.
lbs.).
ND
FRAME & BUMPERS
13 - 21
RECEIVER KIT-TRAILER TOW
REMOVAL
1. Remove the bumper. (Refer to 13 - FRAME &
BUMPERS/BUMPERS/BUMPER-STEP
-
REMOVAL)
2. Disconnect the trailer wiring electrical connectors.
3. Remove the bolts (1) and remove the hitch (2).
INSTALLATION
1. Install the hitch (2) and install the bolts (1).
2. Tighten the bolts to 170 N·m (125 ft. lbs.).
3. Connect the trailer wiring electrical connectors.
4. Install the bumper. (Refer to 13 - FRAME &
BUMPERS/BUMPERS/BUMPER-STEP - INSTAL-
LATION)
13 - 22
FRAME & BUMPERS
ND
FUEL SYSTEM
TABLE OF CONTENTS
page
page
. . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . . . 24
FUEL DELIVERY
TABLE OF CONTENTS
page
page
FUEL DELIVERY
STANDARD PROCEDURE - FUEL SYSTEM
. . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . 2
. . . . . . . . . . . . . . . . 2
. . . . . . . . . . . . . . . . . . . . . . . . 4
SENSOR-FUEL LEVEL SENDING UNIT
. . . . . . . . . . . . . . . . . . . . . . . . . . 5
LINES, FUEL
. . . . . . . . . . . . . . . . . . . . . . . . . . 5
FITTING, QUICK CONNECT
. . . . . . . . . . . . . . . . . . . . . . . . . . 5
STANDARD PROCEDURE - QUICK-CONNECT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
PUMP-FUEL
. . . . . . . . . . . . . . . . . . . . . . . . . . 9
MODULE-FUEL PUMP
. . . . . . . . . . . . . . . . . . . . . . . . . 10
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
. . . . . . . . . . . . . . . . . . . . . . . . . 11
RAIL-FUEL
. . . . . . . . . . . . . . . . . . . . . . . . . 11
. . . . . . . . . . . . . . . . . . . . . . . . . . . 12
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
. . . . . . . . . . . . . . . . . . . . . . . . . 14
TANK-FUEL
. . . . . . . . . . . . . . . . . . . . . . . . . 16
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
. . . . . . . . . . . . . . . . . . . . . . . . . 20
FILTER-INLET
. . . . . . . . . . . . . . . . . . . . . . . . . 23
REGULATOR-FUEL PRESSURE
. . . . . . . . . . . . . . . . . . . . . . . . . 23
FILTER-FUEL
. . . . . . . . . . . . . . . . . . . . . . . . . 23
FUEL DELIVERY
STANDARD PROCEDURE - FUEL SYSTEM PRESSURE RELEASE
Use following procedure if the fuel injector rail is, or is not equipped with a fuel pressure test port.
1. Remove fuel fill cap.
2. Remove fuel pump relay from Power Distribution Center (PDC). For location of relay, refer to label on underside
of PDC cover.
3. Start and run engine until it stalls.
4. Attempt restarting engine until it will no longer run.
5. Turn ignition key to OFF position.
CAUTION: Steps 1, 2, 3 and 4 must be performed to relieve high pressure fuel from within fuel rail. Do not
attempt to use following steps to relieve this pressure as excessive fuel will be forced into a cylinder cham-
ber.
ND
FUEL SYSTEM
14 - 1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст