Dodge Dakota (ND). Manual — part 1287
DISTRIBUTION
TABLE OF CONTENTS
page
page
DUCT-DEFROSTER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
. . . . . . . . . . . . . . . . . . . . . . . . 147
DUCT-FLOOR DISTRIBUTION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
. . . . . . . . . . . . . . . . . . . . . . . . 148
DUCT-INSTRUMENT PANEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
. . . . . . . . . . . . . . . . . . . . . . . . 150
DUCT-INSTRUMENT PANEL DEMISTER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
. . . . . . . . . . . . . . . . . . . . . . . . 152
HOUSING-HVAC
. . . . . . . . . . . . . . . . . . . . . . . . 152
. . . . . . . . . . . . . . . . . . . . . 153
. . . . . . . . . . . . . . . . . . 154
. . . . . . . . . . . . . . . . . . . . . 155
. . . . . . . . . . . . . . . . . . 162
. . . . . . . . . . . . . . . . . . . . . 163
. . . . . . . . . . . . . . . . . . 169
. . . . . . . . . . . . . . . . . . . . . 170
. . . . . . . . . . . . . . . . . . 171
MOTOR-BLOWER
. . . . . . . . . . . . . . . . . . . . . . . . 172
. . . . . . . . . . . . . . . . . . . . . . . . . . 172
. . . . . . . . . . . . . . . . . . . . 172
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 173
. . . . . . . . . . . . . . . . . . . . . . . . 174
OUTLET-AIR
. . . . . . . . . . . . . . . . . . . . . . . . 174
DUCT-DEFROSTER
REMOVAL
WARNING: On vehicles equipped with airbags, disable the airbag system before attempting any steering
wheel, steering column, or instrument panel component diagnosis or service. Disconnect and isolate the
battery negative (ground) cable, then wait two minutes for the airbag system capacitor to discharge before
performing further diagnosis or service. This is the only sure way to disable the airbag system. Failure to
take the proper precautions could result in accidental airbag deployment and possible personal injury or
death.
NOTE: Take the proper precautions to protect the front face of the instrument panel from cosmetic damage
during this service procedure.
24 - 146
DISTRIBUTION
ND
1. Remove the instrument panel and place it on a
workbench (Refer to 23 - BODY/INSTRUMENT
PANEL/INSTRUMENT
PANEL
ASSEMBLY
-
REMOVAL).
2. Remove the screws (1) that secure the defroster
duct (2) to the instrument panel (3) and remove the
duct.
INSTALLATION
1. Position the defroster duct (2) into the instrument
panel (3).
2. Install the screws (1) that secure the defroster duct
to the instrument panel. Tighten the screws to 2
N·m (17 in. lbs.).
3. Install the instrument panel (Refer to 23 - BODY/
INSTRUMENT
PANEL/INSTRUMENT
PANEL
ASSEMBLY - INSTALLATION).
ND
DISTRIBUTION
24 - 147
DUCT-FLOOR DISTRIBUTION
REMOVAL
1. Remove the HVAC Housing and place it on a work-
bench (Refer to 24 - HEATING & AIR CONDITION-
ING/DISTRIBUTION/HOUSING-HVAC
-
REMOVAL).
2. Remove the screws (1) that secure the floor distri-
bution duct (2) to the bottom of the HVAC housing
(3).
3. Remove the floor distribution duct from the HVAC
housing.
INSTALLATION
1. Position the floor distribution duct (2) onto the bot-
tom of the HVAC housing (3).
2. Install the screws (1) that secure the floor distribu-
tion duct to the HVAC housing. Tighten the screws
to 2 N·m (17 in. lbs.).
3. Install the HVAC housing (Refer to 24 - HEATING
& AIR CONDITIONING/DISTRIBUTION/HOUSING-
HVAC - INSTALLATION).
DUCT-INSTRUMENT PANEL
REMOVAL
WARNING: On vehicles equipped with airbags, disable the airbag system before attempting any steering
wheel, steering column, or instrument panel component diagnosis or service. Disconnect and isolate the
battery negative (ground) cable, then wait two minutes for the airbag system capacitor to discharge before
performing further diagnosis or service. This is the only sure way to disable the airbag system. Failure to
take the proper precautions could result in accidental airbag deployment and possible personal injury or
death.
24 - 148
DISTRIBUTION
ND
NOTE: Take the proper precautions to protect the front face of the instrument panel from cosmetic damage
during this service procedure.
1. Remove the instrument panel and place it on a workbench (Refer to 23 - BODY/INSTRUMENT PANEL/INSTRU-
MENT PANEL ASSEMBLY - REMOVAL).
2. Remove the instrument cluster (Refer to 8 - ELECTRICAL/INSTRUMENT CLUSTER - REMOVAL).
3. Remove the defroster duct (4) (Refer to 24 - HEATING & AIR CONDITIONING/DISTRIBUTION/DUCT-DE-
FROSTER - REMOVAL).
4. Remove the wire harness (2) from the center distribution duct (8) and position the wire harness out of the way.
5. Remove the radio coaxial cable (9) from the center distribution duct and the passenger side instrument panel
duct (10) and position the coaxial cable out of the way.
6. Remove the screws that secure the passenger side instrument panel duct, center distribution duct and the center
instrument panel duct (3) to the instrument panel and support assembly (7).
7. Disconnect the passenger side instrument panel duct from the center distribution duct and remove the instrument
panel duct from the instrument panel.
8. Disconnect the center distribution duct from the passenger side demister duct (1).
9. Disconnect the center distribution duct from the center instrument panel duct.
10. Disconnect the center distribution duct from the driver side demister duct (5) and the driver side instrument
panel duct (6) and the remove the center distribution duct from the instrument panel.
11. Remove the center instrument panel duct from the instrument panel.
12. Remove the screws that secure the driver side instrument panel duct to the instrument panel and remove the
duct through the instrument cluster opening.
ND
DISTRIBUTION
24 - 149
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст