Dodge Dakota (ND). Manual — part 389
B1B2D-1st ROW PASSENGER SEAT BELT PRETENSIONER CIRCUIT HIGH (CONTINUED)
2.
CHECK FOR SHORTED PASSENGER SEAT BELT PRETENSIONER
WARNING: To avoid personal injury or death, turn the ignition off,
disconnect the battery and wait two minutes before proceeding.
Disconnect the Passenger Seat Belt Pretensioner connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the 8443 Load Tool and appropriate Jumper to the Passenger
Seat Belt Pretensioner connector.
WARNING: To avoid personal injury or death, turn the ignition on,
then reconnect the battery.
With the scan tool, read the active ORC DTC’s.
Does the scan tool display: B1B2D 1st ROW PASSENGER SEAT
BELT TENSIONER CIRCUIT HIGH?
Yes
>> Go To 3
No
>> Replace the Passenger Seat Belt Pretensioner in accor-
dance with the Service Information.
Perform ORC VERIFICATION TEST - VER 1
3.
CHECK (R56) PASSENGER SEAT BELT TENSIONER LINE 1 CIRCUIT AND (R54) PASSENGER SEAT
BELT TENSIONER LINE 2 CIRCUIT FOR A SHORT TO BATTERY
WARNING: To avoid personal injury or death, turn the ignition off,
disconnect the battery and wait two minutes before proceeding.
Disconnect the 8443 Load Tool and Jumper from the Passenger Seat
Belt Pretensioner connector.
Disconnect the ORC connectors.
NOTE: Check connectors - Clean and repair as necessary.
Connect the 8443 Load Tool ORC Adaptor to the ORC C1 connector.
WARNING: To avoid personal injury or death, turn the ignition on,
then reconnect the battery.
Measure the voltage of the (R56) Passenger Seat Belt Tensioner Line
1 circuit between the Passenger Seat Belt Pretensioner connector and
ground.
Measure the voltage of the (R54) Passenger Seat Belt Tensioner Line
2 circuit between the Passenger Seat Belt Pretensioner connector and
ground.
Is there any voltage present on either circuit?
Yes
>> Repair the Passenger Seat Belt Tensioner circuits with voltage present for a short to battery.
Perform ORC VERIFICATION TEST - VER 1
No
>> Go To 4
8O - 152
RESTRAINTS - ELECTRICAL DIAGNOSTICS
ND
B1B2D-1st ROW PASSENGER SEAT BELT PRETENSIONER CIRCUIT HIGH (CONTINUED)
4.
OCCUPANT RESTRAINT CONTROLLER
WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.
WARNING: If the Occupant Restraint Controller (ORC) is dropped at any time, it must be replaced. Failure to
take the proper precautions can result in accidental airbag deployment and personal injury or death.
NOTE: When reconnecting airbag system components the Ignition must be turned off and the Battery must
be disconnected.
Repair
Replace the ORC in accordance with the Service Information.
Perform ORC VERIFICATION TEST - VER 1
5.
STORED ORC DTC
With the scan tool, record and erase all DTC’s from all Airbag System Modules.
If any ACTIVE codes are present they must be resolved before diagnosing any stored codes.
WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Look for chaffed, pierced, pinched, or partially broken wires and broken, bent, pushed out, spread, corroded, or
contaminated terminals.
The following additional checks may assist you in identifying a possible intermittent problem.
Reconnect any disconnected components and harness connector.
WARNING: To avoid personal injury or death, turn the ignition on, then reconnect the battery.
With the scan tool monitor active codes as you work through the following steps.
Wiggle the wiring harness and connectors of the related airbag circuit or component.
If codes are related to the Driver Airbag circuits, rotate the steering wheel from stop to stop.
If only stored codes return continue the test until the problem area has been isolated.
In the previous steps you have attempted to recreate the conditions responsible for setting active DTC in question.
Are any ACTIVE DTCs present?
Yes
>> Select the appropriate diagnostic procedure from the Table of Contents in this section.
No
>> No problem found at this time. Erase all codes before returning vehicle to customer
ND
RESTRAINTS - ELECTRICAL DIAGNOSTICS
8O - 153
B1B2E-1st ROW PASSENGER SEAT BELT PRETENSIONER CIRCUIT OPEN
8O - 154
RESTRAINTS - ELECTRICAL DIAGNOSTICS
ND
B1B2E-1st ROW PASSENGER SEAT BELT PRETENSIONER CIRCUIT OPEN (CONTINUED)
For the Air Bag System circuit diagram (Refer to 8 - ELECTRICAL/RESTRAINTS - SCHEMATICS AND DIA-
GRAMS).
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
With the ignition on, the Occupant Restraint Controller (ORC) monitors the resistance of the Passenger Seat
Belt Tensioner circuits.
•
Set Condition:
The ORC has detected an open or high resistance on the Passenger Seat Belt Tensioner circuits.
Possible Causes
(R56) PASSENGER SEAT BELT TENSIONER LINE 1 CIRCUIT OR (R54) PASSENGER SEAT BELT TENSIONER
LINE 2 CIRCUIT OPEN
PASSENGER SEAT BELT PRETENSIONER
ORC
Diagnostic Test
1.
DETERMINE ACTIVE OR STORED DTC
NOTE: Ensure the battery is fully charged.
NOTE: The scan tool, SRS Airbag Load Tool MRL 8443, and DVOM are required to perform the following
test.
NOTE: When reconnecting airbag system components the Ignition must be turned off and the Battery must
be disconnected.
Select Active or Stored DTC.
Is the DTC active or stored?
ORC - ACTIVE DTC
Go To 2
ORC - STORED DTC
Go To 6
ND
RESTRAINTS - ELECTRICAL DIAGNOSTICS
8O - 155
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст