Dodge Dakota (ND). Manual — part 467
NOTE: A traveling front outboard seat belt buckle is located on the inboard side of each front outboard seat
section (40 percent) used on all models. The seat belt buckle on the driver’s side front seat for all models
also includes a seat belt switch. (Refer to 8 - ELECTRICAL/RESTRAINTS/SEAT BELT SWITCH -
DESCRIPTION).
1. Position the outboard front seat belt buckle (3)
lower anchor to the mounting hole near the rear of
the inboard seat cushion frame. Be certain the
notch at the base of the anchor engages the anti-
rotation tab on the frame.
2. Install and tighten the screw (1) that secures the
anchor to the frame. Tighten the screw to 43 N·m
(32 ft. lbs.).
3. On the driver side only, route the seat belt switch
pigtail wire (2) under the inboard seat track and the
seat cushion.
4. On the driver side only, move the front seat to its
most forward position and tilt the seat back forward
for easiest access to the seat belt switch pigtail
wire connection.
5. From behind the front seat on the driver side only,
reconnect the seat belt switch pigtail wire connec-
tor (2) to the seat wire harness take out and con-
nector for the switch (3) located below the rear of
the driver side seat cushion (1).
6. Do not reconnect the battery negative cable at this
time. The supplemental restraint system verification
test procedure should be performed following ser-
vice of any supplemental restraint system compo-
nent. (Refer to 8 - ELECTRICAL/RESTRAINTS -
STANDARD
PROCEDURE
-
VERIFICATION
TEST).
FRONT CENTER
WARNING: To avoid personal injury or death, dur-
ing and following any seat belt or child restraint
anchor service, carefully inspect all seat belts,
buckles, mounting hardware, retractors, tether
straps, and anchors for proper installation, opera-
tion, or damage. Replace any belt that is cut, frayed, or torn. Straighten any belt that is twisted. Tighten any
loose fasteners. Replace any belt that has a damaged or inoperative buckle or retractor. Replace any belt
that has a bent or damaged latch plate or anchor plate. Replace any child restraint anchor or the unit to
which the anchor is integral that has been bent or damaged. Never attempt to repair a seat belt or child
restraint component. Always replace damaged or faulty seat belt and child restraint components with the
correct, new and unused replacement parts listed in the DaimlerChrysler Mopar Parts Catalog.
8O - 464
RESTRAINTS - SERVICE INFORMATION
ND
1. From the front of the front seat, insert the front
center seat belt buckle (3) lower anchor through
the opening in the trim (4) on the side of the center
seat cushion.
2. Engage the front center seat belt buckle through
the elastic strap (2) on the side of the center seat
cushion.
3. From behind the front seat, position the seat belt
buckle lower anchor to the center seat support
bracket. Be certain to engage the anti-rotation tab
on the anchor into the corresponding hole in the
center seat support bracket.
4. Install and tighten the screw (5) that secures the
lower anchor to the center seat support bracket.
Tighten the screw to 40 N·m (29 ft. lbs.).
5. Move the adjacent left front outboard seat (1) back
to its rearward position.
REAR - CLUB CAB
WARNING: To avoid personal injury or death, during and following any seat belt or child restraint anchor
service, carefully inspect all seat belts, buckles, mounting hardware, retractors, tether straps, and anchors
for proper installation, operation, or damage. Replace any belt that is cut, frayed, or torn. Straighten any
belt that is twisted. Tighten any loose fasteners. Replace any belt that has a damaged or inoperative buckle
or retractor. Replace any belt that has a bent or damaged latch plate or anchor plate. Replace any child
restraint anchor or the unit to which the anchor is integral that has been bent or damaged. Never attempt to
repair a seat belt or child restraint component. Always replace damaged or faulty seat belt and child
restraint components with the correct, new and unused replacement parts listed in the DaimlerChrysler
Mopar Parts Catalog.
1. Position the lower anchor of the rear seat belt
buckle (2) to the rear floor panel (4).
2. Install and tighten the screw (3) that secures the
buckle anchor to the floor panel. Tighten the screw
to 46 N·m (34 ft. lbs.).
3. Fold down the rear seat cushion from the cab back
panel (1) to the seating position.
ND
RESTRAINTS - SERVICE INFORMATION
8O - 465
REAR CENTER & LEFT OUTBOARD - QUAD CAB
WARNING: To avoid personal injury or death, during and following any seat belt or child restraint anchor
service, carefully inspect all seat belts, buckles, mounting hardware, retractors, tether straps, and anchors
for proper installation, operation, or damage. Replace any belt that is cut, frayed, or torn. Straighten any
belt that is twisted. Tighten any loose fasteners. Replace any belt that has a damaged or inoperative buckle
or retractor. Replace any belt that has a bent or damaged latch plate or anchor plate. Replace any child
restraint anchor or the unit to which the anchor is integral that has been bent or damaged. Never attempt to
repair a seat belt or child restraint component. Always replace damaged or faulty seat belt and child
restraint components with the correct, new and unused replacement parts listed in the DaimlerChrysler
Mopar Parts Catalog.
1. Position the center or the left outboard occupant
buckle unit (2) onto the stud (4) near the base of
the cab back panel that secures the inboard rear
seat mounting bracket to the rear floor panel (5).
2. Install and tighten the nut (3) that secures the
buckle unit to the stud. Tighten the nut to 41 N·m
(30 ft. lbs.). Be certain to hold the buckle in its
properly oriented position while tightening the nut.
3. Push the buckle up through the crevice between
the rear seat cushion and the rear seat back.
4. Lower the rear seat cushion back to its normal
seating position.
5. Engage the buckle through the elastic loop at the
back of the seat cushion.
REAR CENTER ANCHOR & RIGHT OUTBOARD - QUAD CAB
WARNING: To avoid personal injury or death, during and following any seat belt or child restraint anchor
service, carefully inspect all seat belts, buckles, mounting hardware, retractors, tether straps, and anchors
for proper installation, operation, or damage. Replace any belt that is cut, frayed, or torn. Straighten any
belt that is twisted. Tighten any loose fasteners. Replace any belt that has a damaged or inoperative buckle
or retractor. Replace any belt that has a bent or damaged latch plate or anchor plate. Replace any child
restraint anchor or the unit to which the anchor is integral that has been bent or damaged. Never attempt to
repair a seat belt or child restraint component. Always replace damaged or faulty seat belt and child
restraint components with the correct, new and unused replacement parts listed in the DaimlerChrysler
Mopar Parts Catalog.
SEAT BELT & RETRACTOR
REMOVAL
FRONT OUTBOARD - CLUB CAB
WARNING: To avoid personal injury or death, on vehicles equipped with airbags, disable the supplemental
restraint system before attempting any steering wheel, steering column, airbag, occupant classification sys-
tem, seat belt tensioner, impact sensor, or instrument panel component diagnosis or service. Disconnect
and isolate the battery negative (ground) cable, then wait two minutes for the system capacitor to discharge
before performing further diagnosis or service. This is the only sure way to disable the supplemental
restraint system. Failure to take the proper precautions could result in accidental airbag deployment.
8O - 466
RESTRAINTS - SERVICE INFORMATION
ND
WARNING: To avoid personal injury or death, during and following any seat belt or child restraint anchor
service, carefully inspect all seat belts, buckles, mounting hardware, retractors, tether straps, and anchors
for proper installation, operation, or damage. Replace any belt that is cut, frayed, or torn. Straighten any
belt that is twisted. Tighten any loose fasteners. Replace any belt that has a damaged or inoperative buckle
or retractor. Replace any belt that has a bent or damaged latch plate or anchor plate. Replace any child
restraint anchor or the unit to which the anchor is integral that has been bent or damaged. Never attempt to
repair a seat belt or child restraint component. Always replace damaged or faulty seat belt and child
restraint components with the correct, new and unused replacement parts listed in the DaimlerChrysler
Mopar Parts Catalog.
NOTE: The following procedure is for replacement of a faulty or damaged seat belt and retractor unit. The
front retractor also includes a seat belt tensioner. If the front seat belt or retractor is faulty or damaged, but
the seat belt tensioner is not deployed, review the recommended procedures for handling non-deployed
supplemental restraints. (Refer to 8 - ELECTRICAL/RESTRAINTS - STANDARD PROCEDURE - HANDLING
NON-DEPLOYED SUPPLEMENTAL RESTRAINTS). If the seat belt tensioner has been deployed, review the
recommended procedures for service after a supplemental restraint deployment before removing the unit
from the vehicle. (Refer to 8 - ELECTRICAL/RESTRAINTS - STANDARD PROCEDURE - SERVICE AFTER A
SUPPLEMENTAL RESTRAINT DEPLOYMENT).
1. Adjust the front seat to its most forward position for
easiest access to the front seat belt (1) lower
anchor and the retractor (2).
2. Disconnect and isolate the battery negative cable.
Wait two minutes for the system capacitor to dis-
charge before further service.
3. Remove the screw (4) that secures the lower
anchor to the outboard side of the front seat cush-
ion frame (3).
ND
RESTRAINTS - SERVICE INFORMATION
8O - 467
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст