Dodge Dakota (ND). Manual — part 493
B2101-IGNITION RUN/START INPUT LOW (CONTINUED)
3.
FUSED IGNITION SWITCH OUTPUT (RUN-START) CIRCUIT OPENED
NOTE: Check the related fuses to the Fused Ignition Switch Output (Run-Start) circuit. If the fuse is found
to be open, repair the circuit for a shorted condition.
Turn the ignition off.
Disconnect the SKREEM harness connector.
Turn the ignition on.
Using a 12 volt test light connected to ground, probe the Fused Ignition Switch Output (Run-Start) circuit in the
SKREEM harness connector.
Does the test light illuminate brightly?
Yes
>> Go to 4
No
>> Repair the Fused Ignition Switch Output (Run-Start) circuit for an open.
Perform SKREEM VERIFICATION TEST. (Refer to 8 - ELECTRICAL/VEHICLE THEFT SECURITY -
STANDARD PROCEDURE)
4.
SKREEM
NOTE: A dirty (partial) ground can cause abnormal conditions within a system. Ensure the module has a
good ground before continuing.
Turn the ignition off.
Reconnect the SKREEM connector
Back probe the Fused Ignition Switch Output (Run-Start) circuit.
Start the engine.
Using the scan tool, view battery voltage under Data Display in the Engine category.
Compare the voltage on the scan tool to the voltage reading on the voltmeter.
Is the voltage on the scan tool equal to the voltmeter reading +/- .5 volt?
Yes
>> Replace and program the SKREEM in accordance with the Service Information.
Perform SKREEM VERIFICATION TEST. (Refer to 8 - ELECTRICAL/VEHICLE THEFT SECURITY -
STANDARD PROCEDURE)
No
>> Repair the Fused Ignition Switch Output (Run-Start) circuit for high resistance.
Perform SKREEM VERIFICATION TEST. (Refer to 8 - ELECTRICAL/VEHICLE THEFT SECURITY -
STANDARD PROCEDURE)
8Q - 66
VEHICLE THEFT SECURITY - ELECTRICAL DIAGNOSTICS
ND
B2102-IGNITION RUN/START INPUT HIGH
ND
VEHICLE THEFT SECURITY - ELECTRICAL DIAGNOSTICS
8Q - 67
B2102-IGNITION RUN/START INPUT HIGH (CONTINUED)
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
With the ignition switch on.
•
Set Condition:
The SKREEM has detected the ignition switch input voltage above a calibrated value.
Possible Causes
FUSED IGNTION SWITCH OUTPUT (RUN-START) CIRCUIT
SKREEM
Diagnostic Test
1.
DETERMINING IF DTC IS CURRENT
NOTE: Diagnose any related Powertrain DTC(s) before continuing.
With a scan tool, read and record DTC(s).
With the scan tool, clear DTC(s).
Perform 5 ignition cycles, leaving the ignition switch on for a minimum of 90 seconds per cycle.
Using the scan tool, read DTC(s).
Does the DTC reset?
Yes
>> Go To 3
No
>> Go to 2
2.
INTERMITTENT CONDITION
NOTE: Check for any of the follow conditions:
•
Poor wire to terminal connection
•
Corroded terminals
•
Backed out or loose terminals
•
Broken wire internal to the insulation
•
Dirty (partial) module ground
With the ignition on, wiggle the related wires.
Using a scan tool, read DTC(s).
Does the DTC reset?
Yes
>> Repair the wiring as necessary.
Perform SKREEM VERIFICATION TEST. (Refer to 8 - ELECTRICAL/VEHICLE THEFT SECURITY -
STANDARD PROCEDURE)
No
>>
DTC is not active at this time. Test complete.
8Q - 68
VEHICLE THEFT SECURITY - ELECTRICAL DIAGNOSTICS
ND
B2102-IGNITION RUN/START INPUT HIGH (CONTINUED)
3.
FUSED IGNITION SWITCH OUTPUT (RUN-START) CIRCUIT SHORTED TO BATTERY VOLTAGE
NOTE: A dirty (partial) ground can cause abnormal conditions within a system. Ensure the module has a
good ground before continuing.
Turn the ignition off.
Disconnect the SKREEM harness connector.
Using a 12 volt test light connected to ground, probe the Fused Ignition Switch Output (Run-Start) circuit in the
SKREEM harness connector.
Does the test light illuminate brightly?
Yes
>> Repair the Fused Ignition Switch Output (Run-Start) circuit for a short to voltage.
Perform SKREEM VERIFICATION TEST. (Refer to 8 - ELECTRICAL/VEHICLE THEFT SECURITY -
STANDARD PROCEDURE)
No
>> Replace and program the SKREEM in accordance with the Service Information.
Perform SKREEM VERIFICATION TEST. (Refer to 8 - ELECTRICAL/VEHICLE THEFT SECURITY -
STANDARD PROCEDURE)
ND
VEHICLE THEFT SECURITY - ELECTRICAL DIAGNOSTICS
8Q - 69
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст