Dodge Dakota (ND). Manual — part 620
P0032-O2 SENSOR 1/1 HEATER CIRCUIT HIGH (CONTINUED)
3.
(K99) O2 1/1 HEATER CONTROL CIRCUIT
Ignition on, engine not running.
With a scan tool, actuate the O2 1/1 Heater Test with the Sensor har-
ness connector still disconnected.
Using a 12-volt test light connected to ground, probe the (K99) O2 1/1
Heater Control circuit in the O2 Sensor harness connector.
Does the test light illuminate brightly and flash on and off dur-
ing the actuation?
Yes
>> Go To 4
No
>> Go To 5
4.
(Z43) O2 HEATER GROUND CIRCUIT OPEN
Turn the ignition off.
Measure the resistance between an engine ground and the (Z43) O2
1/1 Heater ground circuit in the O2 Sensor harness connector.
Is the resistance below 5.0 ohms?
Yes
>> Replace the O2 Sensor.
Perform POWERTRAIN VERIFICATION TEST. (Refer to 9
- ENGINE - STANDARD PROCEDURE)
No
>> Repair the open in the (Z43) O2 1/1Heater ground circuit.
Perform POWERTRAIN VERIFICATION TEST. (Refer to 9
- ENGINE - STANDARD PROCEDURE)
9 - 18
ENGINE ELECTRICAL DIAGNOSTICS
ND
P0032-O2 SENSOR 1/1 HEATER CIRCUIT HIGH (CONTINUED)
5.
(K99) O2 1/1 HEATER CONTROL CIRCUIT SHORTED TO BATTERY VOLTAGE
Turn the ignition off.
Disconnect the C2 PCM harness connector.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, probe the (K99) O2 1/1
Heater Control circuit in the O2 Sensor harness connector.
Does the test light illuminate brightly?
Yes
>> Repair the short to battery voltage in the (K99) O2 1/1
Heater Control circuit.
Perform POWERTRAIN VERIFICATION TEST. (Refer to 9
- ENGINE - STANDARD PROCEDURE)
No
>> Go To 6
6.
(K99) O2 1/1 HEATER CONTROL CIRCUIT OPEN
Turn the ignition off.
CAUTION: Do not probe the PCM harness connectors. Probing
the PCM hanrness connectors will damage the PCM terminals
resulting in poor terminal to pin connection. Install Miller Special
Tool #8815 to perform diagnosis.
Measure the resistance of the (K99) O2 1/1 Heater Control circuit from
the O2 Sensor harness connector to the appropriate terminal of spe-
cial tool #8815.
Is the resistance below 5.0 ohms?
Yes
>> Go To 7
No
>> Repair the open in the (K99) O2 1/1 Heater Control circuit.
Perform POWERTRAIN VERIFICATION TEST. (Refer to 9
- ENGINE - STANDARD PROCEDURE)
ND
ENGINE ELECTRICAL DIAGNOSTICS
9 - 19
P0032-O2 SENSOR 1/1 HEATER CIRCUIT HIGH (CONTINUED)
7.
PCM
NOTE: Before continuing, check the PCM harness connector terminals for corrosion, damage, or terminal
push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay particular attention to all Power and
Ground circuits.
Were there any problems found?
Yes
>> Repair as necessary.
Perform POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)
No
>> Replace and program the Powertrain Control Module per Service Information.
Perform POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)
9 - 20
ENGINE ELECTRICAL DIAGNOSTICS
ND
P0037-O2 SENSOR 1/2 HEATER CIRCUIT LOW
ND
ENGINE ELECTRICAL DIAGNOSTICS
9 - 21
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст