Dodge Durango (HB). Manual — part 381
5.
(G161) DRIVER DOOR LOCK SWITCH MUX WIRE SHORT TO
VOLTAGE
Disconnect the Driver Memory Mirror Module C1 connector.
Measure the voltage of the (G161) Driver Door Lock Switch Mux cir-
cuit in the Memory Mirror Module connector.
Is there any voltage present?
Yes
>> Repair the (G161) Driver Door Lock Switch Mux circuit for
a short to voltage.
Perform BODY VERIFICATION TEST - VER 1.
No
>> Go to 6
6.
MEMORY SELECT MUX WIRE SHORT TO VOLTAGE
Disconnect the Driver Memory Mirror Module C2 connector.
Measure the voltage of the Memory Select Switch Mux circuit.
Is there any voltage present?
Yes
>> Repair the Memory Select Switch Mux wire for a short to
voltage.
Perform the BODY VERIFICATION TEST - VER 1.
No
>> Replace the Driver Memory Mirror Module.
Perform BODY VERIFICATION TEST - VER 1.
HB
POWER LOCKS - ELECTRICAL DIAGNOSTICS
8N - 37
B1802, B1807 DOOR LOCK/UNLOCK SWITCH CIRCUIT HIGH – MEMORY MIRROR MODULE — (CONTINUED)
8N - 38
POWER LOCKS - ELECTRICAL DIAGNOSTICS
HB
B1803, B1808 DOOR LOCK/UNLOCK SWITCH CIRCUIT STUCK LOCK – MEMORY MIRROR MODULE
For the Power Door Lock circuit diagram (Refer to 8 - ELECTRICAL/POWER LOCKS - SCHEMATICS AND DIA-
GRAMS)
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
Continuously
•
Set Condition:
When the Door Lock Switch Mux circuit is under 2.6 volts for over 30 seconds.
Possible Causes
(G161) DRIVER DOOR LOCK SWITCH MUX WIRE PARTIAL SHORT TO GROUND
(P339) MEMORY SELECT SWITCH MUX WIRE PARTIAL SHORT TO GROUND
(P339) MEMORY SELECT SWITCH MUX CIRCUIT SHORTED TO THE (G920) MEMORY SELECT SWITCH
RETURN CIRCUIT
MEMORY SELECTOR SWITCH
WINDOW/DOOR LOCK SWITCH STUCK
MEMORY MIRROR MODULE
Theory of Operation
This code will only set in vehicles that have the Memory System. The supply circuit for the Memory Mirrors are
supplied by the Memory Mirror Module, therefore both the Memory Select Switch Mux or the Door Lock Switch Mux
circuits can cause this DTC.
Diagnostic Test
1.
TEST FOR INTERMITTENT CONDITION
With the scan tool, record and erase DTC’s
Operate the Door Lock Switch from the side this DTC was set in. Put
the switch in both positions several times.
Cycle the ignition from on to off 3 times.
Turn the ignition on.
With the scan tool, read DTC’s.
Does the scan tool display DOOR LOCK/UNLOCK SWITCH CIR-
CUIT STUCK LOCK?
Yes
>> Go To 2
No
>> The conditions that caused this code to set are not
present at this time. Using the wiring diagram/schematic
as a guide, inspect the wiring and connectors.
Perform BODY VERIFICATION TEST - VER 1.
HB
POWER LOCKS - ELECTRICAL DIAGNOSTICS
8N - 39
B1803, B1808 DOOR LOCK/UNLOCK SWITCH CIRCUIT STUCK LOCK – MEMORY MIRROR MODULE — (CONTINUED)
2.
DRIVER MODULE OR PASSENGER MODULE
Is this DTC in the Driver or Passenger module?
Passenger
Go to 3
Driver
Go to 5
3.
PASSENGER DOOR LOCK SWITCH SHORTED TO GROUND
With the scan tool, erase DTC’s.
Disconnect the Passenger Window/Door Lock Switch connector.
Turn the ignition on.
With the scan tool, read DTC’s.
Does the scan tool display DOOR LOCK/UNLOCK SWITCH CIR-
CUIT STUCK LOCK?
No
>> Replace the Passenger Window/Door Lock Switch.
Perform BODY VERIFICATION TEST - VER 1.
Yes
>> Go to 4
4.
(G160) PASSENGER DOOR LOCK SWITCH MUX CIRCUIT
SHORT TO GROUND
Disconnect the Passenger Memory Mirror Module connector.
Measure the resistance between ground and the (G160) Passenger
Door Lock Switch Mux circuit in the Passenger Memory Mirror Module
connector.
Is the resistance below 10000.0 ohms?
Yes
>> Repair the (G160) Passenger Door Lock Switch Mux cir-
cuit for a short to ground.
Perform BODY VERIFICATION TEST - VER 1.
No
>> Replace the Passenger Memory Mirror Module.
Perform BODY VERIFICATION TEST - VER 1.
8N - 40
POWER LOCKS - ELECTRICAL DIAGNOSTICS
HB
B1803, B1808 DOOR LOCK/UNLOCK SWITCH CIRCUIT STUCK LOCK – MEMORY MIRROR MODULE — (CONTINUED)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст