Dodge Durango (HB). Manual — part 1555
ASSEMBLY
1. If removed, install the two actuator couplers (1) into
the rear HVAC housing. Be sure to install the cou-
plers with the coupler arm (3) located between the
two stop tabs (4) on the HVAC housing.
2. Install the blend-air door (1) and the mode-air door
into the rear HVAC housing (2).
HB
DISTRIBUTION - REAR
24 - 413
3. Align the pivot shafts of the blend-air door (4) and
the mode-air door (5) to the actuator couplers (6)
and install the two halves of the rear HVAC hous-
ing (2) together.
4. Install the screws (3) that secure the two halves of
the rear HVAC housing together. Tighten the
screws to 2 N·m (17 in. lbs.).
5. Install the HVAC wire harness (1). Make sure the
harness is routed through all wiring retainers.
6. Install the rear A/C evaporator (1), rear expansion
valve (2) and the rear extension line bracket (3) as
an assembly into the top of the rear HVAC housing
(4). Make sure that the evaporator drain is clean
and unrestricted and that the evaporator insulator
is properly installed.
24 - 414
DISTRIBUTION - REAR
HB
7. Install the two screws (6) that secure the rear
extension line flange bracket (7) to the bottom of
the rear HVAC housing (2). Tighten the screws to 2
N·m (17 in. lbs.).
8. Install the rear heater core (5) into the side of the
rear HVAC housing. Make sure that the insulator is
properly installed.
9. Install the rear heater core retaining bracket (4).
10. Install the screw (3) that secures the rear heater
core retaining bracket to the rear HVAC housing.
Tighten the screw to 2 N·m (17 in. lbs.).
11. Connect the condensate drain tube (1) to the rear
HVAC housing.
12. Install the outer halve of the rear heater core and
evaporator extension line flange (3).
13. Install the screws (2) that secure the two halves
of the rear heater core and evaporator extension
line flange together. Tighten the screws to 2 N·m
(17 in. lbs.).
14. Install the foam seal (1) to the rear heater core
and evaporator extension line flange.
HB
DISTRIBUTION - REAR
24 - 415
15. Install the blend door actuator (2) and the mode
door actuator (3) to the rear HVAC housing (4)
(Refer to 24 - HEATING & AIR CONDITIONING/
CONTROLS - REAR/ACTUATOR-BLEND DOOR
- INSTALLATION) and (Refer to 24 - HEATING &
AIR CONDITIONING/CONTROLS - REAR/AC-
TUATOR-MODE DOOR - INSTALLATION).
16. Connect the rear HVAC wire harness (1) to the
rear blend door actuator and mode door actuator.
17. Install the rear air inlet housing (6) onto the rear
HVAC housing (1).
18. Install the screws (5) that secure the rear air inlet
housing to the rear HVAC housing. Tighten the
screws to 2 N·m (17 in. lbs.).
19. If removed, install the rear blower motor resistor
(4) (Refer to 24 - HEATING & AIR CONDITION-
ING/CONTROLS
-
REAR/RESISTOR-BLOWER
MOTOR - INSTALLATION).
20. If removed, install the rear blower motor (3) (Refer
to 24 - HEATING & AIR CONDITIONING/DISTRI-
BUTION - REAR/MOTOR-BLOWER - INSTALLA-
TION).
21. Connect the rear HVAC wire harness (2) to the
rear blower motor and the rear blower motor
resistor.
22. Install the rear HVAC housing (Refer to 24 -
HEATING & AIR CONDITIONING/DISTRIBUTION
- REAR/HOUSING-HVAC - INSTALLATION).
24 - 416
DISTRIBUTION - REAR
HB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст