Dodge Durango (HB). Manual — part 97
C1032–RIGHT REAR WHEEL SPEED SENSOR INPUT SIGNAL ERRATIC PERFORMANCE (CONTINUED)
For the Anti-Lock Brake System circuit diagram. (Refer to 5 - BRAKES - SCHEMATICS AND DIAGRAMS)
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
With the ignition on.
•
Set Condition:
When the Right Rear WSS Signal is intermittently missing at a vehicle speed above at 40 kph (25 m.p.h.) or
erratic wheel speed signal during acceleration or sensed wheel speed is different from other wheels.
Possible Causes
RIGHT REAR WSS LOOSE - B1,B2 CIRCUITS/CONNECTOR/TERMINAL DAMAGE
RIGHT REAR TONE WHEEL DAMAGE
RIGHT REAR WSS AIR GAP FAULT
RIGHT REAR WHEEL BEARING DAMAGE
RIGHT REAR BRAKE HARDWARE DAMAGE
RIGHT REAR FRONT WSS - INTERNAL FAULT
ANTI-LOCK BRAKE MODULE - INTERNAL FAULT
Diagnostic Test
1.
CHECK FOR DTC C1032–RIGHT REAR WHEEL SPEED SENSOR INPUT SIGNAL ERRATIC
PERFORMANCE
NOTE: This DTC must be active for the results of this test to be
valid.
Turn the ignition on.
With the scan tool, record and erase DTC’s.
Cycle the ignition switch from off to on.
With the scan tool, read DTC’s
NOTE: The Anti-Lock Brake Module must sense ALL 4 wheels at
12 km/h (7.5 m.p.h.) before it will extinguish the ABS indicators.
Does the scan tool display: C1032–RIGHT REAR WHEEL
SPEED SENSOR INPUT SIGNAL ERRATIC PERFORMANCE and
C102B–RIGHT REAR WHEEL SPEED SENSOR CIRCUIT?
Yes
>> Refer to C102B–Right Rear Wheel Speed Sensor Circuit
for the related symptom(s).
Perform ABS VERIFICATION TEST - VER 1.
No
>> Go To 2
HB
BRAKES - ABS ELECTRICAL DIAGNOSTICS
5 - 167
C1032–RIGHT REAR WHEEL SPEED SENSOR INPUT SIGNAL ERRATIC PERFORMANCE (CONTINUED)
2.
CHECK WHEEL SPEED SENSOR SIGNALS
Turn the ignition on.
With the scan tool, monitor ALL the WSS speeds while an assistant
drives the vehicle.
Slowly accelerate as straight as possible from a stop to 40 km/h (25
m.p.h.).
Is the Right Rear WSS speed showing 0 km/h (0 m.p.h.) or not
matching other wheel speeds?
Yes
>> Go To 3
No
>> Refer to the INTERMITTENT CONDITION diagnostic pro-
cedure.
Perform ABS VERIFICATION TEST - VER 1.
3.
CHECK RIGHT REAR WSS LOOSENESS, INSPECT B1,B2 CIRCUITS/CONNECTORS/TERMINALS FOR
DAMAGE
NOTE: Check all terminals for broken, bent, pushed out, or cor-
roded terminals.
Turn the ignition off.
Inspect the Anti-Lock Brake Module harness connector, Right Rear
WSS, and Right Rear WSS harness connector.
Inspect the Right Rear WSS for looseness and not properly fastened.
Inspect the (B1) Right Rear WSS Signal and (B2) Right Rear WSS
Supply circuits between the Right Rear WSS and Anti-Lock Brake
Module for damage.
Is the Right Rear WSS loose or any of the wiring/connectors/
terminals damaged?
Yes
>> Repair as necessary.
Perform ABS VERIFICATION TEST - VER 1.
No
>> Go To 4
5 - 168
BRAKES - ABS ELECTRICAL DIAGNOSTICS
HB
C1032–RIGHT REAR WHEEL SPEED SENSOR INPUT SIGNAL ERRATIC PERFORMANCE (CONTINUED)
4.
CHECK RIGHT REAR TONE WHEEL FOR DAMAGE
Turn the ignition off.
Inspect the Right Rear Tone Wheel for damage, missing teeth, cracks, or looseness.
NOTE: The Tone Wheel teeth should be perfectly square, not bent, or nicked.
Is the Right Rear Tone Wheel damaged?
Yes
>> Repair as necessary.
Perform ABS VERIFICATION TEST - VER 1.
No
>> Go To 5
5.
CHECK RIGHT REAR WSS AIR GAP
Turn the ignition off.
Using a feeler gauge, measure the Right Rear WSS air gap.
NOTE: Refer to the appropriate service information, if necessary, for procedures or specifications.
Is the Right Rear WSS air gap within specifications?
Yes
>> Go To 6
No
>> Repair as necessary.
Perform ABS VERIFICATION TEST - VER 1.
6.
CHECK RIGHT REAR WHEEL BEARING DAMAGE
Turn the ignition off.
Inspect the Right Rear wheel bearing for excessive runout or clearance.
NOTE: Refer to the appropriate service information, if necessary, for procedures or specifications.
Is the Right Rear Wheel Bearing damaged?
Yes
>> Repair as necessary.
Perform ABS VERIFICATION TEST - VER 1.
No
>> Go To 7
7.
CHECK RIGHT REAR BRAKE HARDWARE DAMAGE
Turn the ignition off.
Visually inspect the Right Rear brake linings for contamination or overheating. Check for dragging, bent, or seized
components/hardware.
Is any brake lining, component, or hardware damaged?
Yes
>> Repair as necessary.
Perform ABS VERIFICATION TEST - VER 1.
No
>> Go To 8
HB
BRAKES - ABS ELECTRICAL DIAGNOSTICS
5 - 169
C1032–RIGHT REAR WHEEL SPEED SENSOR INPUT SIGNAL ERRATIC PERFORMANCE (CONTINUED)
8.
ANTI-LOCK BRAKE MODULE – INTERNAL FAULT
Turn the ignition off.
Replace the Right Rear WSS.
With the scan tool, erase DTC’s.
Road test the vehicle over 40 km/h (25 m.p.h.).
Turn the ignition on.
With the scan tool, read DTC’s
Did the DTC C1032–RIGHT REAR WHEEL SPEED SENSOR
INPUT SIGNAL ERRATIC PERFORMANCE reset?
Yes
>> Replace the Anti-Lock Brake Module in accordance with
the Service Information.
Perform ABS VERIFICATION TEST - VER 1.
No
>> Test Complete.
5 - 170
BRAKES - ABS ELECTRICAL DIAGNOSTICS
HB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст