Dodge Durango (HB). Manual — part 1551
4. If removed, install the mode-air doors into the
upper half of the HVAC housing (2).
5. Align the ends of the blend-air door pivot shafts (1)
to the openings in the upper half of the HVAC
housing and install the upper housing half to the
lower housing half.
6. Install the screws (4) that secure the two halves of
the HVAC housing (3) together. Tighten the screws
to 2.2 N·m (20 in lbs.).
7. Install the HVAC wiring harness (1). Make sure the
harness is routed through all wiring retainers.
8. If removed, install the blower motor resistor or
power module (2), depending on application.
9. Connect the HVAC wire harness to the blower
motor resistor or power module, depending on
application.
HB
DISTRIBUTION - FRONT
24 - 397
10. Install the blower motor (2) to the HVAC housing
(3) (Refer to 24 - HEATING & AIR CONDITION-
ING/DISTRIBUTION - FRONT/MOTOR-BLOWER
- INSTALLATION).
11. Connect the HVAC wire harness (1) to the blower
motor.
12. Carefully install the heater core (6) into the top of
the HVAC housing (3). Make sure that the heater
core insulator is properly positioned.
13. Install the two screws (4) that secure the heater
core retaining bracket (5) to the HVAC housing.
Tighten the screws to 2.2 N·m (20 in. lbs.).
14. Install the HVAC housing bracket (2) to the top of
HVAC housing.
15. Install the two screws (1) that secure the HVAC
housing bracket to the HVAC housing. Tighten the
screws to 2.2 N·m (20 in. lbs.).
24 - 398
DISTRIBUTION - FRONT
HB
16. Install the heater core tube retaining bracket (4) to
the top of the HVAC housing (2).
17. Install the screw (3) that secures the heater core
tube retaining bracket to the HVAC housing.
Tighten the screw to 2.2 N·m (20 in. lbs.).
18. Install the foam seal (1) to the flange on the
HVAC housing.
19. Align the two actuator couplers (1) with the mode-
air door pivot shafts and install the couplers into
the left side of the HVAC housing. Be sure to
install the couplers with the coupler arm located
between the two stop tabs on the HVAC housing.
HB
DISTRIBUTION - FRONT
24 - 399
20. Install the blend door actuator (3) and the mode
door actuators (4) to the HVAC housing (5) (Refer
to 24 - HEATING & AIR CONDITIONING/CON-
TROLS - FRONT/ACTUATOR-BLEND DOOR -
INSTALLATION) and (Refer to 24 - HEATING &
AIR CONDITIONING/CONTROLS - FRONT/AC-
TUATOR-MODE DOOR - INSTALLATION).
21. Install the evaporator temperature sensor (2) into
the top of the HVAC housing.
22. Connect the HVAC wire harness (1) to the evap-
orator temperature sensor, blend door actuator
and the mode door actuators.
23. If removed, install the recirculation door actuator
(3) to the air inlet housing (5).
24. Install the air inlet housing onto the top of the
HVAC housing (1).
25. Install the screws (4) that secure the air inlet
housing to the HVAC housing. Make sure the
HVAC wire harness retainer is properly installed.
26. Connect the HVAC wire harness to the recircula-
tion door actuator (3).
27. Install the HVAC housing (Refer to 24 - HEATING
& AIR CONDITIONING/DISTRIBUTION - FRONT/
HOUSING-HVAC - INSTALLATION).
24 - 400
DISTRIBUTION - FRONT
HB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст