Dodge Durango (HB). Manual — part 1139
10. Disconnect the wiring harness connectors (1) to
the column.
11. Remove the shift cable from the column shift lever
actuator (Refer to 21 - TRANSMISSION/TRANS-
AXLE/AUTOMATIC - 32RH/GEAR SHIFT CABLE
- REMOVAL).
12. Release the shift cable from the column bracket
and remove it from the bracket.
13. Remove the SKIM module in order to disconnect
the electrical connector.
14. Remove the upper steering shaft coupler bolt and
slide the shaft down.
15. Remove the brake light switch (5) and discard
(Refer to 8 - ELECTRICAL/LAMPS/LIGHTING -
EXTERIOR/BRAKE LAMP SWITCH - REMOVAL).
16. Remove the four steering column mounting nuts
(3).
17. Lower the column from the mounting studs (1).
18. Remove the steering column assembly (2) from
the vehicle.
HB
COLUMN
19 - 9
INSTALLATION
WARNING: BEFORE SERVICING THE STEERING
COLUMN THE AIRBAG SYSTEM MUST BE DIS-
ARMED.
REFER
TO
ELECTRICAL
RESTRAINT
SYSTEM FOR SERVICE PROCEDURES. FAILURE
TO DO SO MAY RESULT IN ACCIDENTAL DEPLOY-
MENT OF THE AIRBAG AND POSSIBLE PER-
SONAL INJURY.
CAUTION: All fasteners must be torqued to speci-
fication to ensure proper operation of the steering
column.
1. Position the steering column (2) on the dash panel
support (1) and loosely install the mounting nuts
(3).
2. Firmly slide the steering column (2) upward against
the studs (1) in dash panel and hand tighten the
nuts (3).
3. Install the steering shaft coupler on the steering shaft and loosely install a new bolt.
4. Center steering column (2) in dash opening and tighten mounting nuts (3) to 28 N·m (250 in. lbs.).
NOTE: Torque the upper left nut first then the lower right nut. Then torque the lower left nut then the upper
right nut.
NOTE: A new bolt must be used for reinstallation.
5. Tighten the coupler bolt to 38 N·m (28 ft. lbs.).
6. Install a new brake light switch (5) (Refer to 8 -
ELECTRICAL/LAMPS/LIGHTING
-
EXTERIOR/
BRAKE LAMP SWITCH - REMOVAL).
7. Install the shifter cable. (Refer to 21 - TRANSMIS-
SION/TRANSAXLE/AUTOMATIC
-
32RH/GEAR
SHIFT CABLE - INSTALLATION)
19 - 10
COLUMN
HB
8. Connect the wiring harness (1) to the column (2).
9. Install the SKIM module.
10. Install the clockspring (Refer to 8 - ELECTRICAL/
RESTRAINTS/CLOCKSPRING - REMOVAL).
11. Install the shrouds (1&3).
12. Install the steering column opening reinforcement
(1).
HB
COLUMN
19 - 11
13. Install the steering column opening cover (2)
(Refer to 23 - BODY/INSTRUMENT PANEL/
STEERING
COLUMN
OPENING
COVER
-
INSTALLATION).
14. Align the spline on the steering wheel hub to shaft
(4).
15. Then install the steering wheel (1) and install a
new bolt (2). Tighten the bolt to 61 N·m (45 ft.
lbs.).
16. Install the airbag (Refer to 8 - ELECTRICAL/RE-
STRAINTS/DRIVER AIRBAG - INSTALLATION).
17. Install the tilt lever handle.
18. Install the negative battery terminal.
19. Test the operation of the horn, Electronic PRNDL
Indicator, lights and any other functions that are
steering column operated.
SPECIFICATIONS
TORQUE CHART
TORQUE SPECIFICATIONS
DESCRIPTION
N·m
Ft. Lbs.
In. Lbs.
Tilt Lever Release Knob
Bracket
Mounting Screws
4.5
—
40
Gear Shift Lever Assembly
Mounting Screws
12
—
105
Steering Column
Mounting Nuts
28
—
250
Steering Wheel
Bolt
61
45
—
Steering Coupler Shaft
Upper Pinch Bolt
38
28
—
Steering Coupler Shaft
Lower Pinch Bolt
38
28
—
Toe Plate
Nuts
12
—
105
19 - 12
COLUMN
HB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст