Dodge Durango (HB). Manual — part 471
B1B2E-1st ROW PASSENGER SEAT BELT PRETENSIONER CIRCUIT OPEN
HB
RESTRAINTS - ELECTRICAL DIAGNOSTICS
8O - 153
B1B2E-1st ROW PASSENGER SEAT BELT PRETENSIONER CIRCUIT OPEN (CONTINUED)
For the Air Bag System circuit diagram (Refer to 8 - ELECTRICAL/RESTRAINTS - SCHEMATICS AND DIA-
GRAMS).
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
With the ignition on, the ORC monitors the resistance of the Passenger Seat Belt Tensioner circuits.
•
Set Condition:
The ORC has detected open circuit or high resistance in the Passenger Seat Belt Tensioner circuits.
Possible Causes
(R56) PASSENGER SEAT BELT TENSIONER LINE 1 OR (R54) PASSENGER SEAT BELT TENSIONER LINE 1
CIRCUIT OPEN
PASSENGER SEAT BELT TENSIONER
OCCUPANT RESTRAINT CONTROLLER
Diagnostic Test
1.
DETERMINE ACTIVE OR STORED DTC
NOTE: Ensure the battery is fully charged.
NOTE: The Scan Tool and SRS Airbag Load Tool MRL 8443 are
required to perform the following test.
NOTE: When reconnecting airbag system components the Igni-
tion must be turned off and the Battery must be disconnected.
Select Active or Stored DTC.
Is the DTC active or stored?
ORC - ACTIVE DTC
Go To 2
ORC - STORED DTC
Go To 5
8O - 154
RESTRAINTS - ELECTRICAL DIAGNOSTICS
HB
B1B2E-1st ROW PASSENGER SEAT BELT PRETENSIONER CIRCUIT OPEN (CONTINUED)
2.
PASSENGER SEAT BELT PRETENSIONER CIRCUIT OPEN
WARNING: To avoid personal injury or death, turn the ignition off,
disconnect the battery and wait two minutes before proceeding.
Disconnect the Passenger Airbag connector(s).
NOTE: Check connectors - Clean and repair as necessary.
Connect the 8443 Load Tool and appropriate Jumper to the Passenger
Seat Belt Tensioner harness connector(s).
WARNING: To avoid personal injury or death, turn the ignition on,
then reconnect the battery.
With the scan tool, read the active Occupant Restraint Controller
DTC’s.
Does the scan tool display 1st ROW PASSENGER SEAT BELT
PRETENSIONER CIRCUIT OPEN?
Yes
>> Go to 3
No
>> Replace the Passenger Seat Belt Tensioner in accordance
with Service Information.
Perform AIRBAG VERIFICATION TEST - VER 1
3.
(R56) PASSENGER SEAT BELT TENSIONER LINE 1 OR (R54)
PASSENGER SEAT BELT TENSIONER LINE 2 CIRCUIT OPEN
WARNING: To avoid personal injury or death, turn the ignition off,
disconnect the battery and wait two minutes before proceeding.
Disconnect the 8443 Load Tool and Jumper from the Passenger Seat
Belt Tensioner harness connector(s).
Disconnect the Occupant Restraint Controller harness connector(s).
NOTE: Check connectors - Clean and repair as necessary.
Connect the 8443 Load Tool ORC Adaptor to the ORC harness con-
nector.
Measure the resistance of the (R56) Passenger Seat Belt Tensioner
Line 1 between the Passenger Seat Belt Tensioner harness connector
and the 8443 ORC Adaptor.
Measure the resistance of the (R54) Passenger Seat Belt Tensioner
Line 2 between the Passenger Seat Belt Tensioner harness connector
and the 8443 ORC Adaptor.
Is the resistance below 1.0 ohm on both circuits?
Yes
>> Repair open or high resistance in (R56) Passenger Seat
Belt Tensioner Line 1 or (R54) Passenger Seat Belt Ten-
sioner Line 2.
Perform AIRBAG VERIFICATION TEST - VER 1
No
>> Go to 4
HB
RESTRAINTS - ELECTRICAL DIAGNOSTICS
8O - 155
B1B2E-1st ROW PASSENGER SEAT BELT PRETENSIONER CIRCUIT OPEN (CONTINUED)
4.
OCCUPANT RESTRAINT CONTROLLER
WARNING: If the Occupant Restraint Controller is dropped at any time, it must be replaced. Failure to take
the proper precautions can result in accidental airbag deployment and personal injury or death.
Disconnect the 8443 Load Tool ORC Adaptor from the ORC harness connector.
NOTE: When reconnecting airbag system components the Ignition must be turned off and the Battery must
be disconnected.
If there are no possible causes remaining, view repair.
Repair
Replace the Occupant Restraint Controller in accordance with Service Information.
Perform AIRBAG VERIFICATION TEST - VER 1
5.
STORED ORC DTC
With the scan tool, record and erase all DTC’s from all Airbag System
Modules.
If any ACTIVE codes are present they must be resolved before diag-
nosing any stored codes.
WARNING: To avoid personal injury or death, turn the ignition off,
disconnect the battery and wait two minutes before proceeding.
Using the wiring diagram/schematic as a guide, inspect the wiring and
connectors.
Look for chaffed, pierced, pinched, or partially broken wires and bro-
ken, bent, pushed out, spread, corroded, or contaminated terminals.
The following additional checks may assist you in identifying a possi-
ble intermittent problem.
Reconnect any disconnected components and harness connector.
WARNING: To avoid personal injury or death, turn the ignition on,
then reconnect the battery.
With the scan tool monitor active codes as you work through the fol-
lowing steps.
Wiggle the wiring harness and connectors of the related airbag circuit or component.
If codes are related to the Driver Airbag circuits, rotate the steering wheel from stop to stop.
IF only stored codes return continue the test until the problem area has been isolated.
In the previous steps you have attempted to recreate the conditions responsible for setting active DTC in question.
Are any ACTIVE DTCs present?
Yes
>> Select appropriate symptom from Symptom List.
No
>> No problem found at this time. Erase all codes before returning vehicle to customer.
8O - 156
RESTRAINTS - ELECTRICAL DIAGNOSTICS
HB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст