Dodge Durango (HB). Manual — part 1216
CABLE-GEARSHIFT
DIAGNOSIS AND TESTING - GEARSHIFT CABLE
1. Engine starts must be possible with shift lever in PARK or NEUTRAL positions only. Engine starts must not be
possible in any other gear position.
2. With the shift lever in the:
a. PARK position - Apply upward force on the shift arm and remove pressure. Engine starts must be possible.
b. PARK position - Apply downward force on the shift arm and remove pressure. Engine starts must be pos-
sible.
c. NEUTRAL position - Normal position. Engine starts must be possible.
d. NEUTRAL position - Engine running and brakes applied, apply upward force on the shift arm. Transmission
shall not be able to shift from neutral to reverse.
REMOVAL
1. Shift transmission into PARK.
2. Raise vehicle.
3. Disengage cable (1) eyelet at transmission manual
shift lever (3) and pull cable adjuster out of mount-
ing bracket, RFE transmission equipped vehicles.
HB
AUTOMATIC TRANSMISSION 42RLE - SERVICE INFORMATION
21 - 269
4. Disengage cable (1) eyelet at transmission manual
shift lever (3) and pull cable adjuster out of mount-
ing
bracket
(2),
RLE
transmission
equipped
vehicles.
5. Lower the vehicle.
6. Remove the dash panel insulation pad as neces-
sary to access the gearshift cable grommet (2).
7. Remove grommet (2) from the dash panel.
8. Remove any steering column (1) trim necessary to
access the gearshift cable (2) and BTSI mecha-
nism.
9. Disconnect the BTSI wiring connector (5).
10. Disconnect cable at lower column bracket and
shift lever pin and pull the cable through the dash
panel opening into the vehicle.
11. Remove gearshift cable (2) from vehicle.
21 - 270
AUTOMATIC TRANSMISSION 42RLE - SERVICE INFORMATION
HB
INSTALLATION
1. Route the transmission end of the gearshift cable
(1) through the opening in the dash panel.
2. Seat the cable grommet (2) into the dash panel
opening.
3. Snap the cable into the steering column (1) bracket
so the retaining ears are engaged and snap the
cable eyelet onto the shift lever ball stud.
4. Raise the vehicle.
5. Place the transmission manual shift lever in the
“PARK” detent (rearmost) position and rotate prop
shaft to ensure transmission is in PARK.
HB
AUTOMATIC TRANSMISSION 42RLE - SERVICE INFORMATION
21 - 271
6. Route the gearshift cable (1) through the transmis-
sion mounting bracket (2) and secure the cable by
snapping the cable retaining ears into the transmis-
sion bracket and snapping the cable eyelet on the
manual shift lever (3) ball stud, RLE transmission
equipped vehicles.
7. Route the gearshift cable (1) through the transmis-
sion mounting bracket and secure the cable by
snapping the cable retaining ears into the transmis-
sion bracket and snapping the cable eyelet on the
manual shift lever (3) ball stud, RFE transmission
equipped vehicles.
8. Lower vehicle.
9. Lock the shift cable adjustment by pressing the
cable adjuster lock tab (3) downward until it snaps
into place.
10. Check for proper operation of the transmission
range sensor.
11. Adjust the gearshift cable (Refer to 21 - TRANS-
MISSION/AUTOMATIC/GEAR
SHIFT
CABLE
-
ADJUSTMENTS) and BTSI mechanism (Refer to
21
-
TRANSMISSION/AUTOMATIC/BRAKE
TRANSMISSION SHIFT INTERLOCK SYSTEM -
ADJUSTMENTS) as necessary.
ADJUSTMENTS - GEARSHIFT CABLE
Check adjustment by starting the engine in PARK and NEUTRAL. Adjustment is CORRECT if the engine starts only
in these positions. Adjustment is INCORRECT if the engine starts in one but not both positions. If the engine starts
in any position other than PARK or NEUTRAL, or if the engine will not start at all, the transmission range sensor
may be faulty.
21 - 272
AUTOMATIC TRANSMISSION 42RLE - SERVICE INFORMATION
HB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст