Dodge Durango (HB). Manual — part 1547
DISTRIBUTION - FRONT
TABLE OF CONTENTS
page
page
DUCT-DEFROSTER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 381
. . . . . . . . . . . . . . . . . . . . . . . . 382
DUCT-FLOOR DISTRIBUTION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 383
. . . . . . . . . . . . . . . . . . . . . . . . 384
DUCT-INSTRUMENT PANEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 385
. . . . . . . . . . . . . . . . . . . . . . . . 386
DUCT-INSTRUMENT PANEL DEMISTER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 387
. . . . . . . . . . . . . . . . . . . . . . . . 388
HOUSING-HVAC
. . . . . . . . . . . . . . . . . . . . . . . . 389
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 390
. . . . . . . . . . . . . . . . . . . . . . . . 391
. . . . . . . . . . . . . . . . . . . . . . . . . . . 396
. . . . . . . . . . . . . . . . . . . . . . . . 401
MOTOR-BLOWER
. . . . . . . . . . . . . . . . . . . . . . . . 402
. . . . . . . . . . . . . . . . . . . . . . . . . . 402
. . . . . . . . . . . . . . . . . . . . 402
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 403
. . . . . . . . . . . . . . . . . . . . . . . . 404
OUTLET-AIR
. . . . . . . . . . . . . . . . . . . . . . . . 404
INSTALLATION - DEMISTER OUTLETS
DUCT-DEFROSTER
REMOVAL
WARNING: On vehicles equipped with airbags, disable the airbag system before attempting any steering
wheel, steering column, or instrument panel component diagnosis or service. Disconnect and isolate the
battery negative (ground) cable, then wait two minutes for the airbag system capacitor to discharge before
performing further diagnosis or service. This is the only sure way to disable the airbag system. Failure to
take the proper precautions could result in accidental airbag deployment and possible personal injury or
death.
NOTE: Take the proper precautions to protect the front face of the instrument panel from cosmetic damage.
1. Remove the instrument panel and place it on a
workbench (Refer to 23 - BODY/INSTRUMENT
PANEL/INSTRUMENT
PANEL
ASSEMBLY
-
REMOVAL).
2. Remove the two screws (1) that secure the
defroster duct (2) to the top of the instrument panel
(3).
HB
DISTRIBUTION - FRONT
24 - 381
3. Remove the two screws (1) that secure the
defroster duct (2) to the demister center duct (3).
4. Remove the defroster duct from the instrument
panel (4).
INSTALLATION
1. Position the defroster duct into the instrument
panel.
2. Install the two screws that secure the defroster
duct to the demister center duct. Tighten the
screws to 2 N·m (17 in. lbs.).
24 - 382
DISTRIBUTION - FRONT
HB
3. Install the two screws that secure the defroster
duct to the top of the instrument panel. Tighten the
screws to 2 N·m (17 in. lbs.).
4. Install the instrument panel (Refer to 23 - BODY/
INSTRUMENT
PANEL/INSTRUMENT
PANEL
ASSEMBLY - INSTALLATION).
DUCT-FLOOR DISTRIBUTION
REMOVAL
FRONT FLOOR DISTRIBUTION DUCT
1. Remove the HVAC Housing (Refer to 24 - HEAT-
ING
&
AIR
CONDITIONING/DISTRIBUTION/
HOUSING-HVAC - REMOVAL).
2. Remove the six screws (1) that secure the front
floor distribution duct (2) to the bottom of the HVAC
housing (3).
3. Remove the front floor distribution duct from the
HVAC housing.
HB
DISTRIBUTION - FRONT
24 - 383
INTERMEDIATE FLOOR DISTRIBUTION DUCTS
1. Remove the center floor console (Refer to 23 -
BODY/INTERIOR/FLOOR
CONSOLE
-
REMOVAL).
2. Remove the front seats (Refer to 23 - BODY/
SEATS/SEAT - REMOVAL).
3. Roll back the front floor carpet from under the
instrument panel toward the rear of the vehicle
(Refer to 23 - BODY/INTERIOR/CARPETS AND
FLOOR MATS - REMOVAL).
4. Remove the two push pin fasteners (1) that secure
the right intermediate floor distribution duct (2) and
the left intermediate floor distribution duct (3) to the
floor support (4).
5. Disconnect the left intermediate floor distribution
duct from the front floor distribution duct (5).
6. If required, disconnect the right intermediate floor
distribution duct from the left intermediate floor dis-
tribution duct.
INSTALLATION
FRONT FLOOR DISTRIBUTION DUCT
1. Position the front floor distribution duct (2) to the
bottom of the HVAC housing (3).
2. Install the six screws (1) that secure the front floor
distribution duct to the HVAC housing. Tighten the
screws to 2 N·m (17 in. lbs.).
3. Install the HVAC housing (Refer to 24 - HEATING
& AIR CONDITIONING/DISTRIBUTION/HOUSING-
HVAC - INSTALLATION).
24 - 384
DISTRIBUTION - FRONT
HB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст