Dodge Durango (HB). Manual — part 905
P0580-SPEED CONTROL SWITCH 1 CIRCUIT LOW (5.7L) (CONTINUED)
2.
SPEED CONTROL SWITCHES
Turn the ignition off.
Remove and disconnect the Speed Control Switches from the steering wheel per Service Information.
Measure the resistance across each Speed Control Switch.
Monitor the ohmmeter while pressing each function button on each switch.
The following resistance specs are taken between terminals (V37) S/C Switch No.1 Signal and (V937) S/C Switch
Return circuits of the Switch when holding the switch button in the following positions.
Not pressing any switch - 20.5 kohms
On/Off - 0.47 kohms
Set - 5.49 kohms
Coast - 2.94 kohms
Cancel - 1.24 kohms
Resume/Accel - 15.4 kohms
Does the function on the Speed Control Switches have the correct resistance value?
Yes
>> Go To 3
No
>> Replace the Speed Control Switch that had the incorrect resistance value.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)
3.
SPEED CONTROL ON/OFF SWITCH
Connect the Resume/Accel Switch.
Ignition on, engine not running.
With the scan tool, monitor the Speed Control Switch voltage.
Disconnect the Speed Control On/Off Switch harness connector.
Did the voltage change to above 4.8 volts?
Yes
>> Replace the Speed Control On/Off Switch.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)
No
>> Go To 4
4.
SPEED CONTROL RESUME/ACCEL SWITCH
With the scan tool, monitor the Speed Control Switch voltage.
Disconnect the Speed Control Resume/Accel Switch harness connector per Service Information.
Did the voltage change to above 4.8 volts?
Yes
>> Replace the Speed Control Resume/Accel Switch.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)
No
>> Go To 5
HB
ENGINE ELECTRICAL DIAGNOSTICS
9 - 619
P0580-SPEED CONTROL SWITCH 1 CIRCUIT LOW (5.7L) (CONTINUED)
5.
CLOCKSPRING
Turn the ignition off.
Disconnect the C1 Clockspring harness connector per Service Information.
Ignition on, engine not running.
With the scan tool, read the S/C Switch voltage.
Did the S/C Switch volts change to 5.0 volts?
Yes
>> Replace the Clockspring.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)
No
>> Go To 6
6.
(V37) S/C SWITCH NO.1 SIGNAL CIRCUIT SHORTED TO THE (V937) S/C SWITCH RETURN CIRCUIT
Turn the ignition off.
Connect the Clockspring harness connectors per Service Information.
Disconnect the C3 PCM harness connector.
CAUTION: Do not probe the PCM harness connectors. Probing
the PCM harness connectors will damage the PCM terminals
resulting in poor terminal to pin connection. Install Miller Special
Tool #8815 to perform diagnosis.
Measure the resistance between the (V937) S/C Switch Return circuit
and the (V37) S/C Switch No.1 Signal circuit at the Speed Control
Switch.
Is the resistance below 5.0 ohms?
Yes
>> Repair the short between the (V37) S/C Switch No.1 Sig-
nal circuit and the (V937) S/C Switch Return circuit.
Perform the POWERTRAIN VERIFICATION TEST. (Refer
to 9 - ENGINE - STANDARD PROCEDURE)
No
>> Go To 7
7.
(V37) S/C SWITCH NO.1 SIGNAL CIRCUIT SHORTED TO GROUND
Measure the resistance between ground and the (V37) S/C Switch
No.1 Signal circuit in the Switch harness connector.
Is the resistance below 100 ohms?
Yes
>> Repair the short to ground in the (V37) S/C Switch No.1
Signal circuit.
Perform the POWERTRAIN VERIFICATION TEST. (Refer
to 9 - ENGINE - STANDARD PROCEDURE)
No
>> Go To 8
9 - 620
ENGINE ELECTRICAL DIAGNOSTICS
HB
P0580-SPEED CONTROL SWITCH 1 CIRCUIT LOW (5.7L) (CONTINUED)
8.
SPEED CONTROL SWITCH VOLTAGE VALUES
Connect the C3 PCM harness connector and the S/C Switch harness connectors.
Allow the engine to idle.
With a scan tool, monitor the S/C Switch voltage readings.
SWITCH POSITION
SWITCH No.1 VOLTAGE VALUE
SWITCH No.2 VOLATGE VALUE
NO SWITCHES PRESSED
4.31 to 4.78 volts
4.31 to 4.78 volts
ON/OFF PRESSED
0.59 and 1.13 volts
3.53 and 3.92 volts
RES/ACCEL PRESSED
3.88 to 4.17 volts
2.04 to 2.47 volts
SET PRESSED
3.16 to 3.56 volts
1.17 to 1.56 volts
COAST PRESSED
2.57 to 2.94 volts
0.77 to 1.09 volts
CANCEL PRESSED
1.59 to 1.99 volts
2.84 to 3.25 volts
Take these same voltage measurements with a voltmeter by back probing the (V37) S/C Switch No.1 Signal circuit
at the switches.
Compare the voltage readings on the voltmeter to what the scan tool displayed.
Are the voltage readings out of the listed specification and is there less than a 0.2 of a volt difference
between the voltmeter switch values and the scan tool switch value?
Yes
>> Replace the Speed Control Switch.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)
No
>> Go To 9
9.
PCM
NOTE: Before continuing, check the PCM harness connector terminals for corrosion, damage, or terminal
push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay particular attention to all Power and
Ground circuits.
Were there any problems found?
Yes
>> Repair as necessary.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)
No
>> Replace and program the Powertrain Control Module per Service Information.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)
HB
ENGINE ELECTRICAL DIAGNOSTICS
9 - 621
P0581-SPEED CONTROL SWITCH 1 CIRCUIT HIGH (3.7L, 4.7L)
9 - 622
ENGINE ELECTRICAL DIAGNOSTICS
HB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст