Dodge Ram Truck 1500-2500-3500. Manual — part 937
P0592-SPEED CONTROL SWITCH 2 CIRCUIT LOW (CONTINUED)
6.
(V38) S/C SWITCH NO.2 SIGNAL CIRCUIT SHORTED TO THE (V937) SWITCH RETURN CIRCUIT
Measure the resistance between the (V937) Switch Return circuit and
the (V38) S/C Switch No.2 Signal circuit in the Speed Control Switch.
Is the resistance below 5.0 ohms?
Yes
>> Repair the short between the (V38) S/C Switch No.2 Sig-
nal circuit and the (V937) Switch Return circuit.
Perform the POWERTRAIN VERIFICATION TEST. (Refer
to 9 - ENGINE - STANDARD PROCEDURE)
No
>> Go To 7
9 - 670
ENGINE - ELECTRICAL DIAGNOSTICS - 3.7L/4.7L/5.7L
DR/DH
P0592-SPEED CONTROL SWITCH 2 CIRCUIT LOW (CONTINUED)
7.
SPEED CONTROL SWITCH VOLTAGE VALUES
Allow the engine to idle.
With a scan tool, monitor the S/C Switch voltage readings.
SWITCH POSITION
SWITCH No.1 VOLTAGE VALUE
SWITCH No.2 VOLATGE VALUE
NO SWITCHES PRESSED
4.31 to 4.78 volts
4.31 to 4.78 volts
ON/OFF PRESSED
0.59 to 1.13 volts
3.53 to 3.92 volts
RES/ACCEL PRESSED
3.88 to 4.17 volts
2.04 to 2.47 volts
SET PRESSED
3.16 to 3.56 volts
1.17 to 1.56 volts
COAST PRESSED
2.57 to 2.94 volts
0.77 to 1.09 volts
CANCEL PRESSED
1.59 to 1.99 volts
2.84 to 3.25 volts
Take these same voltage measurements with a voltmeter by back probing the (V38) S/C Switch No.2 Signal circuit
at the switches.
Compare the voltage readings on the voltmeter to what the scan tool displayed.
Are the voltage readings out of the listed specification and is there less than a 0.2 of a volt difference
between the voltmeter switch values and the scan tool switch values?
Yes
>> Replace the Speed Control Switch.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)
No
>> Go To 8
8.
PCM
NOTE: Before continuing, check the PCM harness connector terminals for corrosion, damage, or terminal
push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay particular attention to all Power and
Ground circuits.
Were there any problems found?
Yes
>> Repair as necessary.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)
No
>> Replace and program the Powertrain Control Module per Service Information.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)
DR/DH
ENGINE - ELECTRICAL DIAGNOSTICS - 3.7L/4.7L/5.7L
9 - 671
P0593-SPEED CONTROL SWITCH 2 CIRCUIT HIGH
9 - 672
ENGINE - ELECTRICAL DIAGNOSTICS - 3.7L/4.7L/5.7L
DR/DH
P0593-SPEED CONTROL SWITCH 2 CIRCUIT HIGH (CONTINUED)
For the Engine circuit diagram (Refer to 9 - ENGINE - SCHEMATICS AND DIAGRAMS).
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
With the ignition key on.
•
Set Condition:
Speed Control Switch No.2 input above the maximum acceptable voltage at the PCM. One trip fault.
Possible Causes
(V38) S/C SIGNAL NO.2 CIRCUIT SHORTED TO VOLTAGE
(V38) S/C SWITCH NO.2 SIGNAL CIRCUIT OPEN BETWEEN THE PCM AND CLOCKSPRING
(V937) SWITCH RETURN CIRCUIT OPEN BETWEEN PCM AND CLOCKSPRING
(V38) S/C SWITCH NO.2 SIGNAL CIRCUIT OPEN BETWEEN THE CLOCKSPRING AND S/C SWITCH
(V937) SWITCH RETURN CIRCUIT OPEN BETWEEN CLOCKSPRING AND S/C SWITCH
CLOCKSPRING
SPEED CONTROL SWITCH
PCM
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING).
Diagnostic Test
1.
SPEED CONTROL SWITCH VOLTAGE HIGH
NOTE: Do not press any of the Speed Control Switch buttons.
Ignition on, engine not running.
With a scan tool, read the Speed Control voltage.
Is the Speed Control voltage above 4.8 volts?
Yes
>> Go To 2
No
>> Refer to the INTERMITTENT CONDITION Diagnostic Procedure.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)
DR/DH
ENGINE - ELECTRICAL DIAGNOSTICS - 3.7L/4.7L/5.7L
9 - 673
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст