Dodge Ram Truck 1500-2500-3500. Manual — part 276
CABIN EQ MISMATCH (CONTINUED)
3.
FCM ACTIVE ON THE BUS CIRCUIT
With the DRBIII
T
, attempt to communicate with the FCM.
Are you able to communicate with the FCM?
Yes
>> Go To 4
No
>> Refer to the Communication Category for related symptoms/DTCs.
Perform BODY VERIFICATION TEST - VER 1.
4.
ACTIVE DTCS STORED IN THE FCM
With the DRBIII
T
, erase FCM DTCs.
Turn the ignition off.
Wait at least 10 seconds.
Turn the ignition on.
With the DRBIII
T
, read FCM DTCs.
Are any DTCs active present?
Yes
>> Refer to the symptom list for problems related to the Front Control Module.
Perform BODY VERIFICATION TEST - VER 1.
No
>> Replace the Front Control Module per Service Information.
Perform BODY VERIFICATION TEST - VER 1.
8A - 106
AUDIO - SRT10 - AMP - ELECTRICAL DIAGNOSTICS
DR/DH
SOFTWARE CHECKSUM FAILURE
For the Audio Amplifier system circuit diagram (Refer to 8 - ELECTRICAL/AUDIO - SCHEMATICS AND DIA-
GRAMS).
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
With the ignition on
•
Set Condition:
The Amplifier sets an internal software failure
Possible Causes
AMPLIFIER
1.
Amplifier
Turn the ignition on.
Turn the radio on.
With the DRBIII
T
, erase Amplifier DTCs.
With the DRBIII
T
, reset the Amplifier.
With the DRBIII
T
, read Amplifier DTCs.
Is the DTC: SOFTWARE CHECKSUM FAILURE
active at this time?
Yes
>> Replace the Amplifier in accordance
with the service information.
No
>> The conditions that caused this code to
set are not present at this time. Use the
wiring diagrams/schematics as a guide
to locate and inspect the related wiring
and connectors.
Perform BODY VERIFICATION TEST -
VER 1.
DR/DH
AUDIO - SRT10 - AMP - ELECTRICAL DIAGNOSTICS
8A - 107
BATTERY VOLTAGE LOW
For the Audio Amplifier system circuit diagram (Refer to 8 - ELECTRICAL/AUDIO - SCHEMATICS AND DIA-
GRAMS).
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
With the ignition on.
•
Set Condition:
If the module detects the battery voltage being less and 9.0 volts for greater than 1 second.
Possible Causes
BATTERY VOLTAGE LOW AT AMPLIFIER
CHARGING SYSTEM DTCS IN PCM
AMPLIFIER
1.
INTERMITTENT CONDITION
Cycle the ignition switch from on to off to on.
With the DRBIII
T
, read Amplifier DTCs.
Is the DTC active at this time?
Yes
>> Go To 2
No
>> The conditions that caused this code to
set are not present at this time. Use the
wiring diagrams/schematics as a guide
to locate and inspect the related wiring
and connectors.
Perform BODY VERIFICATION TEST -
VER 1.
2.
BATTERY VOLTAGE LOW AT AMPLIFIER
With the DRBIII
T
in Data Display, read the Amplifier battery voltage.
Is the voltage less than 9.0 volts?
Yes
>> Go To 3
No
>> Replace the Amplifier per Service Information.
Perform BODY VERIFICATION TEST - VER 1.
8A - 108
AUDIO - SRT10 - AMP - ELECTRICAL DIAGNOSTICS
DR/DH
BATTERY VOLTAGE LOW (CONTINUED)
3.
CHARGING SYSTEM DTCS IN PCM
With the DRBIII
T
read PCM DTCs.
Are any Charging System related DTCs set in the PCM?
Yes
>> Diagnose and repair the DTCs using the Powertrain Diagnostic Manual.
Perform BODY VERIFICATION TEST - VER 1.
No
>> Replace the Amplifier per Service Information.
Perform BODY VERIFICATION TEST - VER 1.
DR/DH
AUDIO - SRT10 - AMP - ELECTRICAL DIAGNOSTICS
8A - 109
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст