Dodge Ram Truck 1500-2500-3500. Manual — part 576
INTERNAL FAULT
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
With the ignition on.
•
Set Condition:
The SKIM has detected a fault during an internal self test.
Possible Causes
SKIM INTERNAL DTC FAILURE
Diagnostic Test
1.
SKIM INTERNAL DTC PRESENT
NOTE: Note: This trouble code indicates an internal SKIM fault.
With the scan tool, read and record the SKIM DTCs and then erase the SKIM DTCs
Perform 5 ignition key cycles, leaving the ignition key on for a minimum of 90 seconds per cycle.
With the scan tool, read the SKIM DTCs.
Did the same SKIM DTC return?
Yes
>> Replace and program the Sentry Key Immobilizer Module in per Service Information.
Perform SKIS VERIFICATION. (Refer to 8 - ELECTRICAL/VEHICLE THEFT SECURITY - STANDARD
PROCEDURE)
No
>> Test complete, the conditions that set this DTC are not present at this time.
8Q - 6
VEHICLE THEFT SECURITY - ELECTRICAL DIAGNOSTICS
DR/DH
RAM FAILURE
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
With the ignition on.
•
Set Condition:
The RAM fails a test that checks the RAM’s ability to retain memory.
Possible Causes
SKIM INTERNAL DTC FAILURE
Diagnostic Test
1.
SKIM INTERNAL DTC PRESENT
NOTE: Note: This trouble code indicates an internal SKIM fault.
With the scan tool, read and record the SKIM DTCs and then erase the SKIM DTCs
Perform 5 ignition key cycles, leaving the ignition key on for a minimum of 90 seconds per cycle.
With the scan tool, read the SKIM DTCs.
Did the same SKIM DTC return?
Yes
>> Replace and program the Sentry Key Immobilizer Module in per Service Information.
Perform SKIS VERIFICATION. (Refer to 8 - ELECTRICAL/VEHICLE THEFT SECURITY - STANDARD
PROCEDURE)
No
>> Test complete, the conditions that set this DTC are not present at this time.
DR/DH
VEHICLE THEFT SECURITY - ELECTRICAL DIAGNOSTICS
8Q - 7
SERIAL LINK INTERNAL FAULT
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
With the ignition on.
•
Set Condition:
The SKIM fails an internal J1850 communication self test.
Possible Causes
SKIM INTERNAL DTC FAILURE
Diagnostic Test
1.
SKIM INTERNAL DTC PRESENT
NOTE: Note: This trouble code indicates an internal SKIM fault.
With the scan tool, read and record the SKIM DTCs and then erase the SKIM DTCs
Perform 5 ignition key cycles, leaving the ignition key on for a minimum of 90 seconds per cycle.
With the scan tool, read the SKIM DTCs.
Did the same SKIM DTC return?
Yes
>> Replace and program the Sentry Key Immobilizer Module in per Service Information.
Perform SKIS VERIFICATION. (Refer to 8 - ELECTRICAL/VEHICLE THEFT SECURITY - STANDARD
PROCEDURE)
No
>> Test complete, the conditions that set this DTC are not present at this time.
8Q - 8
VEHICLE THEFT SECURITY - ELECTRICAL DIAGNOSTICS
DR/DH
STOCK OVERFLOW FAILURE
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
With the ignition on.
•
Set Condition:
The micro controller has exceeded its stack space limit.
Possible Causes
SKIM INTERNAL DTC FAILURE
Diagnostic Test
1.
SKIM INTERNAL DTC PRESENT
NOTE: Note: This trouble code indicates an internal SKIM fault.
With the scan tool, read and record the SKIM DTCs and then erase the SKIM DTCs
Perform 5 ignition key cycles, leaving the ignition key on for a minimum of 90 seconds per cycle.
With the scan tool, read the SKIM DTCs.
Did the same SKIM DTC return?
Yes
>> Replace and program the Sentry Key Immobilizer Module in per Service Information.
Perform SKIS VERIFICATION. (Refer to 8 - ELECTRICAL/VEHICLE THEFT SECURITY - STANDARD
PROCEDURE)
No
>> Test complete, the conditions that set this DTC are not present at this time.
DR/DH
VEHICLE THEFT SECURITY - ELECTRICAL DIAGNOSTICS
8Q - 9
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст