Dodge Ram Truck 1500-2500-3500. Manual — part 407
FCM-LEFT HIGHBEAM OUTPUT CIRCUIT OPEN (CONTINUED)
For the Exterior Lighting system circuit diagram (Refer to 8 - ELECTRICAL/LAMPS/LIGHTING - EXTERIOR -
SCHEMATICS AND DIAGRAMS).
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
With the ignition on
•
Set Condition:
The FCM detects an OPEN condition
Possible Causes
LEFT HIGHBEAM OUTPUT CIRCUIT OPEN
POWER DISTRIBUTION CENTER
FRONT CONTROL MODULE
1.
INTERMITTENT CONDITION
Turn the ignition on.
With the DRBIII
T
, clear all FCM DTC’s.
Turn the Highbeam Lamps on.
With the DRBIII
T
, read the DTC information.
Does the DRBIII
T
read: Left Highbeam Output
Circuit Open?
Yes
>> Go To 2
No
>> The condition that caused the symptom is
currently not present. Inspect the related
wiring for a possible intermittent condition.
Look for any chafed, pierced, pinched, or
partially broken wires.
Perform BODY VERIFICATION TEST -
VER 1.
8L - 34
LAMPS/LIGHTING - EXTERIOR - ELECTRICAL DIAGNOSTICS
DR/DH
FCM-LEFT HIGHBEAM OUTPUT CIRCUIT OPEN (CONTINUED)
2.
LEFT HIGHBEAM OUTPUT CIRCUIT OPEN
Turn the ignition off.
Disconnect the IPM C7 harness connector
Measure the resistance of the Left Highbeam Output circuit.
Is the resistance above 5.0 ohms?
Yes
>> Repair the Left Highbeam Output circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
No
>> Go To 3
3.
FRONT CONTROL MODULE
Turn the ignition off
Disconnect the FCM from the IPM.
Disconnect the IPM C7 harness connector.
Measure the resistance of the Left Highbeam Output circuit.
Is the resistance above 5.0 ohms?
Yes
>> Replace the Power Distribution Center..
Perform BODY VERIFICATION TEST - VER 1.
No
>> Replace the Front Control Module.
Perform BODY VERIFICATION TEST - VER 1.
DR/DH
LAMPS/LIGHTING - EXTERIOR - ELECTRICAL DIAGNOSTICS
8L - 35
FCM-LEFT LOWBEAM OUTPUT CIRCUIT LOW
8L - 36
LAMPS/LIGHTING - EXTERIOR - ELECTRICAL DIAGNOSTICS
DR/DH
FCM-LEFT LOWBEAM OUTPUT CIRCUIT LOW (CONTINUED)
For the Exterior Lighting system circuit diagram (Refer to 8 - ELECTRICAL/LAMPS/LIGHTING - EXTERIOR -
SCHEMATICS AND DIAGRAMS).
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
With the ignition on
•
Set Condition:
The FCM detects a short to ground condition
Possible Causes
LEFT LOWBEAM OUTPUT CIRCUIT SHORT TO GROUND
POWER DISTRIBUTION CENTER
FRONT CONTROL MODULE
1.
INTERMITTENT CONDITION
Turn the ignition on.
With the DRBIII
T
, clear all FCM DTC’s.
Turn the Lowbeam Lamps on.
With the DRBIII
T
, read the DTC information.
Does the DRBIII
T
read: Left Lowbeam Output
Circuit Low?
Yes
>> Go To 2
No
>> The condition that caused the symptom is
currently not present. Inspect the related
wiring for a possible intermittent condition.
Look for any chafed, pierced, pinched, or
partially broken wires.
Perform BODY VERIFICATION TEST -
VER 1.
DR/DH
LAMPS/LIGHTING - EXTERIOR - ELECTRICAL DIAGNOSTICS
8L - 37
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст