Dodge Ram Truck 1500-2500-3500. Manual — part 376
*ALL GAUGES INOPERATIVE
8J - 64
INSTRUMENT CLUSTER - ELECTRICAL DIAGNOSTICS
DR/DH
*ALL GAUGES INOPERATIVE (CONTINUED)
For a complete wiring diagram Refer to Section 8W.
Possible Causes
NO RESPONSE - PCI BUS
NO RESPONSE - PCI BUS - POWERTRAIN CONTROL MODULE
PCI BUS - INSTRUMENT CLUSTER
(F21) FUSED IGNITION SWITCH OUTPUT (RUN/START) CIRCUIT SHORT TO GROUND
(F1) FUSED IGNITION SWITCH OUTPUT (OFF/RUN/START) CIRCUIT SHORT TO GROUND
(F21) FUSED IGNITION SWITCH OUTPUT (RUN/START) CIRCUIT OPEN
(F1) FUSED IGNITION SWITCH OUTPUT (OFF/RUN/START) CIRCUIT OPEN
(Z18) INSTRUMENT CLUSTER GROUND CIRCUIT FOR AN OPEN
INSTRUMENT CLUSTER
Diagnostic Test
1.
NO RESPONSE - PCI BUS
NOTE: NOTE: Diagnose and repair any MIC, PCM (ECM if diesel equipped), or Communication DTCs before
proceeding with this test.
Turn the ignition on.
With the DRBIII
T
, select System Monitors, then J1850 Module Scan.
Does the DRBIII
T
display MIC PRESENT on the BUS?
Yes
>> Go To 2
No
>> Refer to the COMMUNICATION category and perform the appropriate symptom.
Perform BODY VERIFICATION TEST - VER 1. (Refer to BODY VERIFICATION TEST - VER 1.)
2.
NO RESPONSE - PCI BUS - POWERTRAIN CONTROL MODULE
Turn the ignition on.
With the DRBIII
T
, select Body, MIC, SYSTEM TESTS, PCM Monitor.
Does the DRBIII
T
display PCM INACTIVE on the BUS?
Yes
>> Refer to the COMMUNICATION category and perform the appropriate symptom.
Perform BODY VERIFICATION TEST - VER 1. (Refer to BODY VERIFICATION TEST - VER 1.)
No
>> Go To 3
3.
PCI BUS - INSTRUMENT CLUSTER
Turn the ignition on.
With the DRBIII
T
, select Body, MIC, MODULE DISPLAY.
Does the DRBIII
T
display NO RESPONSE from MIC?
Yes
>> Refer to the COMMUNICATION category and perform the appropriate symptom.
Perform BODY VERIFICATION TEST - VER 1. (Refer to BODY VERIFICATION TEST - VER 1.)
No
>> Go To 4
DR/DH
INSTRUMENT CLUSTER - ELECTRICAL DIAGNOSTICS
8J - 65
*ALL GAUGES INOPERATIVE (CONTINUED)
4.
CHECK THE (F21) FUSED IGNITION SWITCH OUTPUT (RUN/START) CIRCUIT FOR A SHORT TO
GROUND
Turn the ignition off.
Inspect the #20 Fuse in the PDC.
If the fuse is open, replace with proper rated fuse.
Turn the ignition on for one minute.
Turn the ignition off.
Inspect the #20 Fuse in the PDC.
Is the fuse open?
Yes
>> Repair the (F21) Fused Ignition Switch Output (Unlock/
Run) circuit for a short to ground.
Perform BODY VERIFICATION TEST - VER 1. (Refer to
BODY VERIFICATION TEST - VER 1.)
No
>> Go To 5
5.
CHECK THE (F1) FUSED IGNITION SWITCH OUTPUT (OFF/RUN/START) CIRCUIT FOR A SHORT TO
GROUND
Turn the ignition off.
Remove and inspect the #29 Fuse in the PDC.
If the fuse is open, replace with the proper rated fuse.
Turn the ignition on for 1 minute.
Turn the ignition off.
Remove and inspect the #29 Fuse in the PDC.
Is the fuse open?
Yes
>> Repair the (F1) Fused Ignition Switch Output (Run/Start)
circuit for a short to ground.
Perform BODY VERIFICATION TEST - VER 1. (Refer to
BODY VERIFICATION TEST - VER 1.)
No
>> Go To 6
8J - 66
INSTRUMENT CLUSTER - ELECTRICAL DIAGNOSTICS
DR/DH
*ALL GAUGES INOPERATIVE (CONTINUED)
6.
CHECK THE (F21) FUSED IGNITION SWITCH OUTPUT (RUN/START) CIRCUIT FOR AN OPEN
Turn the ignition off.
Disconnect the Instrument Cluster C3 harness connector.
Turn the ignition on.
Measure the voltage between the (F21) Fused Ignition Switch Output
(Run/Start) circuit and ground.
Is the voltage below 10.5 volts?
Yes
>> Repair the (F21) Fused Ignition Switch Output (Run/Start)
circuit for an open.
Perform BODY VERIFICATION TEST - VER 1. (Refer to
BODY VERIFICATION TEST - VER 1.)
No
>> Go To 7
7.
CHECK THE (F1) FUSED IGNITION SWITCH OUTPUT (OFF/RUN/START) CIRCUIT FOR AN OPEN
Turn the ignition off.
Disconnect the Instrument Cluster C3 harness connector.
Turn the ignition on.
Measure the voltage between the (F1) Fused Ignition Switch Output
(Off/Run/Start) circuit and ground.
Is the voltage below 10.5 volts?
Yes
>> Repair the (F1) Fused Ignition Switch Output (Off/Run/
Start) circuit for an open.
Perform BODY VERIFICATION TEST - VER 1. (Refer to
BODY VERIFICATION TEST - VER 1.)
No
>> Go To 8
DR/DH
INSTRUMENT CLUSTER - ELECTRICAL DIAGNOSTICS
8J - 67
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст