Dodge Ram Truck 1500-2500-3500. Manual — part 1939
5. Install the two screws (3) that secure the body side cladding to the front fender. Tighten the screws to 5 N·m (44
in. lbs.).
SPOILER - SRT-10
REMOVAL
WITHOUT CARGO BOX COVER
1. Remove the two bolts (2) that secure the spoiler to
the rear of the cargo box.
2. Slide the spoiler rearward to disengage the two
studs (1) and remove the spoiler.
3. If required, remove the two nuts that secure the
two studs to the rear of the cargo box and remove
the studs.
WITH CARGO BOX COVER
1. Remove the five nuts (1) that secure the spoiler (2)
to the cargo box cover (3).
2. Remove the spoiler from the cargo box cover
.
23 - 110
EXTERIOR
DR/DH
INSTALLATION
WITHOUT CARGO BOX COVER
1. If removed, position the two studs (1) onto the rear
of the cargo box and install the retaining nuts.
Tighten the nuts to 9 N·m (80 in. lbs.).
2. Position the spoiler over the two studs and slide
the spoiler forward until the studs fully engage.
3. Install the two bolts (2) that secure the spoiler to
the rear of the cargo box. Tighten the bolts to 6
N·m (50 in. lbs.).
WITH CARGO BOX COVER
1. Position the spoiler (2) onto the rear of the cargo
box cover (3).
2. Install the five nuts (1) that secure the spoiler to
the cargo box cover. Tighten the nuts to 9 N·m (80
in. lbs.).
DR/DH
EXTERIOR
23 - 111
HOOD
TABLE OF CONTENTS
page
page
BEZEL-HOOD SRT-10
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
. . . . . . . . . . . . . . . . . . . . . . . . 113
HINGE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
. . . . . . . . . . . . . . . . . . . . . . . . 115
HOOD
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
. . . . . . . . . . . . . . . . . . . . . . . . 116
LATCH
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
. . . . . . . . . . . . . . . . . . . . . . . . 117
LATCH RELEASE CABLE/HANDLE ASSEMBLY
REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . 118
. . . . . . . . . . . . . . . . . . . . . . . . 118
LATCH STRIKER / SECONDARY CATCH
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
. . . . . . . . . . . . . . . . . . . . . . . . 119
SUPPORT CYLINDER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
. . . . . . . . . . . . . . . . . . . . . . . . 121
BEZEL-HOOD SRT-10
REMOVAL
NOTE: If the hood scoop bezel is removed for any
reason, it should be replaced.
1. Remove the four nuts that secure the hood scoop
bezel to the hood.
23 - 112
HOOD
DR/DH
2. Using a trim stick C-4755 or equivalent, disengage
the upper retaining clips (2) for the hood scoop
bezel (3) from the hood scoop (1).
3. Rotate the front of the hood scoop bezel upward,
toward the rear of the hood to separate the upper
retaining clips from the hood scoop.
CAUTION: If the upper retaining clips come off of
the bezel during removal, DO NOT open the hood.
This will help prevent the retaining clips from
becoming lost inside the hood.
NOTE: If required, use a magnet to remove any
retaining clips that may have fallen off of the hood
scoop bezel during removal.
4. Remove the hood scoop bezel from the hood.
INSTALLATION
NOTE: If the hood scoop bezel is removed for any
reason, it should be replaced.
1. Position the hood scoop bezel (3) into the hood
scoop (1) and rotate it forward and downward to
engage the upper retaining clips (2) to the hood
scoop as shown.
DR/DH
HOOD
23 - 113
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст