Dodge Ram Truck 1500-2500-3500. Manual — part 1858
SPECIFICATIONS
TRANSFER CASE - NV241 GENII
TORQUE SPECIFICATIONS
DESCRIPTION
N-m
Ft. Lbs.
In. Lbs.
Plug, Detent
16-24
12-18
-
Plug, Drain/Fill
20-34
15-25
-
Bolt, Extension Housing
16-24
12-18
-
Bolt, Case Half
20-27
15-24
-
Screw, Oil Pump
12-16
8-12
-
Nut, Range Lever
27-34
20-25
-
Sector Support
27-42
20-30
-
Nuts, Mounting
30-41
20-30
-
Position Sensor
20-34
16-25
-
21 - 1364
TRANSFER CASE - NV241 GENII - SERVICE INFORMATION
DR/DH
SPECIAL TOOLS
TRANSFER CASE - NV241/NV243
Handle, Universal - C-4171
Installer, Seal - 6888
Installer, Bearing - 6953
Installer, Seal - C-4210
Remover, Bushing - 6957
Installer, Bushing - 8157
Installer, Seal - D-163
Installer, Seal - 7884
DR/DH
TRANSFER CASE - NV241 GENII - SERVICE INFORMATION
21 - 1365
Installer, Bushing - 5066
Plug, Extension - C-293-3
Remover - L-4454
Cup - 8148
Installer, Pump Housing Seal - 7888
21 - 1366
TRANSFER CASE - NV241 GENII - SERVICE INFORMATION
DR/DH
SEAL-EXTENSION HOUSING
REMOVAL
1. Raise and support vehicle.
2. Remove rear propeller shaft. (Refer to 3 - DIFFERENTIAL & DRIVELINE/PROPELLER SHAFT/PROPELLER
SHAFT - REMOVAL)
3. Using a suitable pry tool or slide-hammer mounted screw, remove the extension housing seal.
INSTALLATION
1. Clean fluid residue from sealing surface and
inspect for defects.
2. Using Installer D-163 (2) and Handle C-4171 (1),
install seal in extension housing.
3. Install propeller shaft. (Refer to 3 - DIFFERENTIAL
& DRIVELINE/PROPELLER SHAFT/PROPELLER
SHAFT - INSTALLATION)
4. Verify proper transfer case fluid level.
5. Lower vehicle.
FLUID
STANDARD PROCEDURE - FLUID DRAIN AND REFILL
The fill (2) and drain (3) plugs are both in the rear
case.
1. Raise vehicle.
2. Position drain pan under transfer case.
NOTE: It may be necessary to remove the exhaust
y-pipe at the exhaust manifold to properly access
the fill and drain plugs. Lowering the exhaust will
allow the plugs to be accessed for torquing during
installation. (Refer to 11 - EXHAUST SYSTEM/EX-
HAUST PIPE - REMOVAL)
3. Remove drain and fill plugs and drain lubricant
completely.
4. Install drain plug. Tighten plug to 20-34 N·m (15-25
ft. lbs.).
5. Remove drain pan.
6. Fill transfer case to bottom edge of fill plug opening with Mopar
T
ATF +4, Automatic Transmission fluid.
7. Install and tighten fill plug to 20-34 N·m (15-25 ft. lbs.).
8. Install the exhaust y-pipe to the exhaust manifold, if removed. (Refer to 11 - EXHAUST SYSTEM/EXHAUST
PIPE - INSTALLATION)
9. Wipe any excess fluid that may have spilled onto the exhaust.
10. Lower vehicle.
DR/DH
TRANSFER CASE - NV241 GENII - SERVICE INFORMATION
21 - 1367
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст