Dodge Ram Truck 1500-2500-3500. Manual — part 485
DRIVER DOOR MODULE SWITCH TESTS
UP
PINS 3 & 7
DOWN
PINS 2 & 3
RIGHT
PINS 2 & 3
LEFT
PINS 3 & 4
POWER WINDOW SWITCH
SWITCH POSITION
CONTINUITY BETWEEN
PINS OF CONNECTOR
C-1
NEUTRAL
PINS 1 & 8, PINS 2 & 8,
PINS 3 & 8, PINS 4 & 8,
PINS 5 & 8, PINS 6 & 8,
PINS 8 & 10, PINS 8 &
12
LEFT FRONT UP
PINS 5 & 9
LEFT FRONT DOWN
PINS 9 & 12
RIGHT FRONT UP
PINS 3 & 9
RIGHT FRONT DOWN
PINS 6 & 9
LEFT REAR UP
PINS 4 & 9
LEFT REAR DOWN
PINS 9 & 10
RIGHT REAR UP
PINS 2 & 9
RIGHT REAR DOWN
PINS 1 & 9
POWER WINDOW LOCKOUT SWITCH
SWITCH POSITION
CONTINUITY BETWEEN
OFF (SWITCH BUTTON
RAISED - NOT
DEPRESSED)
PIN 9 OF CONNECTOR
C-1 & PIN 8 OF
CONNECTOR C-2
REMOVAL
1. Disconnect and isolate the battery negative cable.
2. Remove the door trim panel (Refer to 23 - BODY/DOOR - FRONT/TRIM PANEL - REMOVAL).
3. Remove the switch from the trim panel bezel.
INSTALLATION
1. Install switch to trim panel bezel.
2. Install door trim panel (Refer to 23 - BODY/DOOR - FRONT/TRIM PANEL - INSTALLATION).
3. Connect battery negative cable.
8N - 82
POWER LOCKS - SERVICE INFORMATION
DR/DH
TRANSMITTER-REMOTE KEYLESS ENTRY
DIAGNOSIS AND TESTING
REMOTE KEYLESS ENTRY TRANSMITTER
Using special tool 9001, first test to ensure that the
transmitter is functioning. Typical testing distance is
2.5 centimeters (1 inch) for Asian transmitters and
30.5 centimeters (12 inches) for all others. To test,
position the transmitter as shown. Press any transmit-
ter button, then test each button individually. The tool
will beep if a radio signal strength that lights five or
more LED’s is detected. Repeat this test three times.
If transmitter fails any of the test refer to the Diagnos-
tic Procedures information.
STANDARD PROCEDURE
STANDARD PROCEDURE - RKE TRANSMITTER BATTERIES
NOTE: Do not disturb the metal terminal near the batteries. Avoid touching the new batteries. Skin oils may
cause battery deterioration. If batteries are touched, clean with rubbing alcohol.
The Remote Keyless Entry (RKE) transmitter case snaps open and shut for battery access. To replace the RKE
transmitter batteries:
1. Using a thin coin, gently pry at the notch in the center seam of the RKE transmitter case halves near the key ring
until the two halves unsnap. Be careful not to damage the rubber gasket when separating the case halves.
2. Lift the back half of the transmitter case off of the RKE transmitter.
3. Remove the two batteries from the RKE transmitter.
4. Replace the two batteries with new 3V lithium 2016 cell. Install the batteries with the positive terminal up. Ref-
erence the “+ SIDE UP” on the inside of the bottom half of the transmitter case.
5. Align the two RKE transmitter case halves with each other, and squeeze them firmly and evenly together until
they snap back into place. Test transmitter operation.
STANDARD PROCEDURE - RKE TRANSMITTER CUSTOMER PREFERENCES
AUTOMATIC (ROLLING) LOCKS
The rolling locks feature can be toggled ON/OFF by using a scan tool only.
HORN CHIRP DISABLING / ENABLING
The horn chirp can be toggled using a scan or by using the Remote Keyless Entry (RKE) transmitter that is already
programmed to the vehicle.
To DISABLE (cancel) the horn chirp feature:
1. Enter the vehicle and close all doors.
2. Fasten the seat belt (this will cancel the seat belt chime).
3. Turn the ignition to the ON position.
DR/DH
POWER LOCKS - SERVICE INFORMATION
8N - 83
4. Press and hold the LOCK button for 4 seconds. Within 6 seconds with the LOCK button still depressed, press
the UNLOCK button. When a single chime is heard, release both buttons.
5. Turn the ignition OFF.
6. Turn the ignition ON or wait 60 seconds.
7. Test the horn chirp feature by pressing the LOCK button.
If a chime is not heard, program mode was canceled before the feature could be disabled. If necessary, repeat the
procedure.
To ENABLE the horn chirp feature, repeat the above procedure.
OPTICAL CHIRP (FLASH) DISABLING / ENABLING
The optical chirp can be toggled using a scan tool or by using the Remote Keyless Entry (RKE) transmitter that is
already programmed to the vehicle.
To DISABLE (cancel) the optical chirp feature:
1. Enter the vehicle and close all doors.
2. Fasten the seat belt (this will cancel the seat belt chime).
3. Turn the ignition to the ON position.
4. Press and hold the LOCK button for 4 seconds. Within 6 seconds with the LOCK button still depressed, press
the PANIC button. When a single chime is heard, release both buttons.
5. Turn the ignition OFF.
6. Turn the ignition ON or wait 60 seconds.
7. Test the optical chirp feature by pressing the LOCK button.
If a chime is not heard, program mode was canceled before the feature could be disabled. If necessary, repeat the
procedure.
To ENABLE the optical chirp feature, repeat the above procedure.
UNLOCK SEQUENCE
The unlock sequence can be toggled using a scan tool or by using the Remote Keyless Entry (RKE) transmitter that
is already programmed to the vehicle.
To toggle between Driver door first and Unlock all doors function:
1. Enter the vehicle and close all doors.
2. Fasten the seat belt (this will cancel the seat belt chime).
3. Turn the ignition to the ON position.
4. Press and hold the UNLOCK button for 4 seconds. Within 6 seconds with the UNLOCK button still depressed,
press the LOCK button. When a single chime is heard, release both buttons.
5. Turn the ignition OFF.
6. Turn the ignition ON or wait 60 seconds.
If a chime is not heard, program mode was canceled before the feature could be disabled. If necessary, repeat the
procedure.
To toggle this feature, repeat the above procedure.
STANDARD PROCEDURE - RKE TRANSMITTER PROGRAMING
New Remote Keyless Entry (RKE) transmitters can be programed using the DRB III
T
scan tool and the proper Diag-
nostic Procedures manual. The DRB III
T
scan tool can provide confirmation that the PCI data bus is functional, and
that all of the electronic modules are sending and receiving the proper messages on the PCI data bus.
The following procedure can be used as long as one programmed transmitter is available:
NOTE: When entering program mode using that programmed fob, ALL currently programmed fobs will be
erased and they will have to be reprogrammed for the vehicle. If program mode is entered and no action is
performed, the previously programmed fobs will continue to function.
1. Enter the vehicle and close all doors.
8N - 84
POWER LOCKS - SERVICE INFORMATION
DR/DH
2. Fasten the seat belt (this will cancel the seat belt chime). Turn the ignition to the RUN position.
3. Press and hold the UNLOCK button on a programmed transmitter for 4 to 10 seconds. Within the 4 to 10 sec-
onds with the UNLOCK button still depressed, press the PANIC button for one second. When a single chime is
heard, release both buttons.The chime indicates the system is in program mode.
4. Press and release both the LOCK and UNLOCK buttons simultaneously on a fob to be programmed. A single
chime will be heard, this indicates the fob has been recognized.
5. Press and release any button on the same fob. A single chime will be heard, this indicates the fob has been
programmed.
6. Repeat steps 4 and 5 for up to a total of 4 fobs.
7. Turn the ignition OFF.
8. Turn the ignition ON or wait 60 seconds.
The vehicle will remain in program mode for up to 60 seconds from when the original chime (step 3) was heard.
After 60 seconds, all programmed transmitters will function normally.
SPECIFICATIONS
REMOTE KEYLESS ENTRY TRANSMITTER
RANGE
Normal operation range is up to a distance of 3 to 7 meters (10 to 23 ft.) of the vehicle. Range may be better or
worse depending on the environment around the vehicle.
DR/DH
POWER LOCKS - SERVICE INFORMATION
8N - 85
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст