Dodge Ram Truck 1500-2500-3500. Manual — part 1105
P0581-HIGH VOLTAGE DETECTED AT THE SPEED CONTROL SWITCH (CONTINUED)
9.
S/C SWITCH GROUND CIRCUIT OPEN ECM TO CLOCKSPRING
Measure the resistance of the S/C Switch Sensor Ground Circuit
between the ECM harness connector to the clockspring harness con-
nector.
Is the resistance below 5.0 ohms?
Yes
>> Replace and program the ECM in accordance with the
Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)
No
>> Repair open ground circuit from ECM to clockspring.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)
9 - 1342
ENGINE - ELECTRICAL DIAGNOSTICS - DIESEL
DR/DH
P0602-CHECKSUM ERROR
For the Engine circuit diagram (Refer to 9 - ENGINE - SCHEMATICS AND DIAGRAMS)
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
While the ignition is on.
•
Set Condition:
A deviation between the ECM memory and a stored calibration.
Possible Causes
FLASH ECM
ECM
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING)
Diagnostic Test
1.
FLASH ECM
Using the scan tool, reflash the ECM with the proper calibration for the particular truck.
Is the flash successful?
Yes
>> Repair complete.
No
>> Go To 2
2.
ECM
With the scan tool, read DTCs.
Did P0602 set after the reflash?
Yes
>> Replace the ECM.
No
>> Test Complete.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
DR/DH
ENGINE - ELECTRICAL DIAGNOSTICS - DIESEL
9 - 1343
P0604-ECM SOFTWARE ERROR
For the Engine circuit diagram (Refer to 9 - ENGINE - SCHEMATICS AND DIAGRAMS)
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
While the key is on.
•
Set Condition:
Internal ECM software error.
Possible Causes
REFLASH ECM
ECM
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING)
Diagnostic Test
1.
REFLASH ECM
Using the scan tool, reflash the module with latest calibration
Was the flash successful?
Yes
>> Go To 2
No
>> Replace the ECM.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
2.
ECM
Run the engine for one minute and shut off.
With the scan tool, read DTCs.
Did P0604 set?
Yes
>> Replace the ECM.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
No
>> Test Complete.
9 - 1344
ENGINE - ELECTRICAL DIAGNOSTICS - DIESEL
DR/DH
P0606-ECM HARDWARE ERROR
For the Engine circuit diagram (Refer to 9 - ENGINE - SCHEMATICS AND DIAGRAMS)
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
With the key on or engine running.
•
Set Condition:
ECM had detected internal failures.
Possible Causes
ECM
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING)
Diagnostic Test
1.
ECM
Turn the ignition on.
NOTE: This DTC is caused by an internal Engine Control Module failure. Repairs are not possible to the
ECM.
With the scan tool, erase DTCs.
Is the DTC still set?
Yes
>> Replace and program the ECM in accordance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
No
>> Test Complete.
DR/DH
ENGINE - ELECTRICAL DIAGNOSTICS - DIESEL
9 - 1345
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст