Dodge Ram Truck 1500-2500-3500. Manual — part 564
WARNING: To avoid personal injury or death, use extreme care to prevent any foreign material from enter-
ing the passenger airbag, or becoming entrapped between the passenger airbag cushion and the passenger
airbag door. Failure to observe this warning could result in occupant injuries upon airbag deployment.
NOTE: The following procedure is for replacement of a faulty or damaged passenger airbag. If the airbag is
faulty or damaged, but not deployed, review the recommended procedures for handling non-deployed sup-
plemental restraints. (Refer to 8 - ELECTRICAL/RESTRAINTS - STANDARD PROCEDURE - HANDLING NON-
DEPLOYED SUPPLEMENTAL RESTRAINTS). If the passenger airbag has been deployed, review the
recommended procedures for service after a supplemental restraint deployment before removing the airbag
from the vehicle. (Refer to 8 - ELECTRICAL/RESTRAINTS - STANDARD PROCEDURE - SERVICE AFTER A
SUPPLEMENTAL RESTRAINT DEPLOYMENT).
1. Carefully position the passenger airbag and airbag
door (1) to the instrument panel as a unit.
2. Reconnect the passenger airbag pigtail wire con-
nector to the instrument panel wire harness con-
nector for the airbag. This connector is secured to
the inboard side of the airbag housing. Be certain
that the latch on the connector and the red
Connector Position Assurance (CPA) lock are
each fully engaged.
3. Position the passenger airbag housing and door
unit into the instrument panel.
4. Using hand pressure, press firmly and evenly over each of the seven snap features on the upper and outboard
edges of the passenger airbag door until they snap into their receptacles in the instrument panel base trim.
5. Reach through and above the glove box opening to install and tighten the two screws (3) that secure the pas-
senger airbag front brackets to the instrument panel structural support. Tighten the screws to 6 N·m (55 in. lbs.).
6. Reach through and above the glove box opening to install and tighten the two screws (4) that secure the pas-
senger airbag rear brackets to the upper glove box opening reinforcement (2). Tighten the screws to 6 N·m (55
in. lbs.).
7. Install and tighten the six screws (4) that secure
the inboard and lower flanges of the passenger air-
bag door (1) to the instrument panel. Tighten the
screws to 2 N·m (20 in. lbs.).
8. Install and tighten the screw (2) that secures the
mounting tab of the panel outlet housing to the
upper glove box opening reinforcement (3). Tighten
the screw to 2 N·m (20 in. lbs.).
9. Reinstall the lower surround onto the instrument
panel. (Refer to 23 - BODY/INSTRUMENT PANEL/
LOWER SURROUND - INSTALLATION).
10. Do not reconnect the battery negative cable at
this time. The supplemental restraint system verification test procedure should be performed following service of
any supplemental restraint system component. (Refer to 8 - ELECTRICAL/RESTRAINTS - STANDARD PRO-
CEDURE - VERIFICATION TEST).
8O - 290
RESTRAINTS - SERVICE INFORMATION
DR/DH
SEAT BELT
REMOVAL - FRONT CENTER
WARNING: To avoid personal injury or death, during and following any seat belt or child restraint anchor
service, carefully inspect all seat belts, buckles, mounting hardware, retractors, tether straps, and anchors
for proper installation, operation, or damage. Replace any belt that is cut, frayed, or torn. Straighten any
belt that is twisted. Tighten any loose fasteners. Replace any belt that has a damaged or inoperative buckle
or retractor. Replace any belt that has a bent or damaged latch plate or anchor plate. Replace any child
restraint anchor or the unit to which the anchor is integral that has been bent or damaged. Never attempt to
repair a seat belt or child restraint component. Always replace damaged or faulty seat belt and child
restraint components with the correct, new and unused replacement parts listed in the DaimlerChrysler
Mopar Parts Catalog.
NOTE: A fixed position front center seat belt buckle is located on the left side of the front center seat sec-
tion (20 percent) used on all models. Standard cab models also have a unique fixed position black, keyed
front center seat belt lower anchor buckle for the three-point center seat belt lower anchor located on the
right side of the front center seat section. The following procedure also applies to the fixed position front
center seat lap belt located on the right side of the front center seat section of all quad cab models. The
three-point front center seat belt and retractor unit is only used on standard cab models. (Refer to 8 - ELEC-
TRICAL/RESTRAINTS/FRONT CENTER SEAT BELT & RETRACTOR - REMOVAL).
1. Move the adjacent right or left front outboard seat
section (40 percent) to its most forward position for
easiest access to the front center seat belt buckle,
lap belt lower anchor, or unique black, keyed front
center seat belt lower anchor buckle (1).
2. From behind the front seat, remove the screw (5)
that secures the front center seat belt buckle, lap
belt lower anchor, or unique black, keyed front cen-
ter seat belt lower anchor buckle to the center seat
support bracket (3).
3. From the front of the front seat, reach between the
center seat cushion (6) and the adjacent right or
left front outboard seat cushion to access and
remove the front center seat belt buckle, lap belt
unit, or unique black, keyed front center seat belt
lower anchor buckle through the elastic strap (2) on
the side of the center seat cushion.
4. Remove the front center seat belt buckle, lap belt
unit, or unique black, keyed front center seat belt
lower anchor buckle from the front seat.
INSTALLATION - FRONT CENTER
WARNING: To avoid personal injury or death, during and following any seat belt or child restraint anchor
service, carefully inspect all seat belts, buckles, mounting hardware, retractors, tether straps, and anchors
for proper installation, operation, or damage. Replace any belt that is cut, frayed, or torn. Straighten any
belt that is twisted. Tighten any loose fasteners. Replace any belt that has a damaged or inoperative buckle
or retractor. Replace any belt that has a bent or damaged latch plate or anchor plate. Replace any child
restraint anchor or the unit to which the anchor is integral that has been bent or damaged. Never attempt to
repair a seat belt or child restraint component. Always replace damaged or faulty seat belt and child
restraint components with the correct, new and unused replacement parts listed in the DaimlerChrysler
Mopar Parts Catalog.
DR/DH
RESTRAINTS - SERVICE INFORMATION
8O - 291
NOTE: A fixed position front center seat belt buckle is located on the left side of the front center seat sec-
tion (20 percent) used on all models. Standard cab models also have a unique fixed position black, keyed
front center seat belt lower anchor buckle for the three-point center seat belt lower anchor located on the
right side of the front center seat section. The following procedure also applies to the fixed position front
center seat lap belt located on the right side of the front center seat section of all quad cab models. The
three-point front center seat belt and retractor unit is only used on standard cab models. (Refer to 8 - ELEC-
TRICAL/RESTRAINTS/FRONT CENTER SEAT BELT & RETRACTOR - INSTALLATION).
1. From the front of the front seat, position the front
center seat belt buckle, lap belt unit, or unique
black, keyed front center seat belt lower anchor
buckle (1) between the center seat cushion (6) and
the adjacent right or left front outboard seat cush-
ion.
2. From the front of the front seat, reach between the
center seat cushion and the adjacent right or left
front outboard seat cushion to route the front cen-
ter seat belt buckle, lap belt unit lower anchor, or
unique black, keyed front center seat belt lower
anchor buckle through the elastic strap (2) on the
side of the center seat cushion.
3. From behind the front seat, position the front center
seat belt buckle, lap belt lower anchor, or unique
black, keyed front center seat belt lower anchor
buckle to the center seat support bracket (3). Be
certain to engage the anti-rotation tab on the
buckle or belt anchor into the corresponding hole in
the center seat support bracket.
4. Install and tighten the screw (5) that secures the front center seat belt buckle, lap belt lower anchor, or unique
black, keyed front center seat belt lower anchor buckle to the center seat support bracket. Tighten the screw to
40 N·m (29 ft. lbs.).
5. Move the adjacent right or left front outboard seat section (40 percent) back to its rearward position.
SEAT BELT BUCKLE
REMOVAL
FRONT OUTBOARD
WARNING: To avoid personal injury or death, during and following any seat belt or child restraint anchor
service, carefully inspect all seat belts, buckles, mounting hardware, retractors, tether straps, and anchors
for proper installation, operation, or damage. Replace any belt that is cut, frayed, or torn. Straighten any
belt that is twisted. Tighten any loose fasteners. Replace any belt that has a damaged or inoperative buckle
or retractor. Replace any belt that has a bent or damaged latch plate or anchor plate. Replace any child
restraint anchor or the unit to which the anchor is integral that has been bent or damaged. Never attempt to
repair a seat belt or child restraint component. Always replace damaged or faulty seat belt and child
restraint components with the correct, new and unused replacement parts listed in the DaimlerChrysler
Mopar Parts Catalog.
NOTE: A traveling front outboard seat belt buckle is located on the inboard side of each front outboard seat
section (40 percent) used on all models. The seat belt buckle on the driver’s side front seat for all models
also includes a seat belt switch. (Refer to 8 - ELECTRICAL/RESTRAINTS/SEAT BELT SWITCH -
DESCRIPTION).
8O - 292
RESTRAINTS - SERVICE INFORMATION
DR/DH
1. Move the right or left front outboard seat section
(2) to its most rearward position and tilt the seat
back forward for easiest access to the front out-
board seat belt buckle lower anchor.
2. For easiest access to the front outboard seat belt
buckle lower anchor on standard cab models, also
move the outboard seat section opposite the side
from which the buckle is to be removed to its most
forward position and tilt the seat back forward.
3. On standard cab models only, remove the stowage
tray from the rear floor panel behind the seat.
(Refer to 23 - BODY/INTERIOR/REAR FLOOR
STOWAGE TRAY - REMOVAL).
4. From behind the front seat on the driver side only,
disconnect the seat belt switch pigtail wire (3) con-
nector from the seat wire harness take out and
connector for the switch located below the inboard
edge of the driver side inboard seat track (4) just
forward of the buckle lower anchor.
5. From behind the front seat, remove the screw (5) that secures the front outboard seat belt buckle (1) lower
anchor to the bracket on the inboard seat track.
6. From the front of the front seat, reach between the center seat cushion and the adjacent right or left front out-
board seat cushion to access and remove the front outboard seat belt buckle from the seat.
FRONT CENTER & CENTER ANCHOR
WARNING: To avoid personal injury or death, during and following any seat belt or child restraint anchor
service, carefully inspect all seat belts, buckles, mounting hardware, retractors, tether straps, and anchors
for proper installation, operation, or damage. Replace any belt that is cut, frayed, or torn. Straighten any
belt that is twisted. Tighten any loose fasteners. Replace any belt that has a damaged or inoperative buckle
or retractor. Replace any belt that has a bent or damaged latch plate or anchor plate. Replace any child
restraint anchor or the unit to which the anchor is integral that has been bent or damaged. Never attempt to
repair a seat belt or child restraint component. Always replace damaged or faulty seat belt and child
restraint components with the correct, new and unused replacement parts listed in the DaimlerChrysler
Mopar Parts Catalog.
NOTE: A fixed position front center seat belt buckle is located on the left side of the front center seat sec-
tion (20 percent) used on all models. Standard cab models also have a unique fixed position black, keyed
front center seat belt lower anchor buckle for the three-point center seat belt lower anchor located on the
right side of the front center seat section. The following procedure also applies to the fixed position front
center seat lap belt located on the right side of the front center seat section of all quad cab models. The
three-point front center seat belt and retractor unit is only used on standard cab models. (Refer to 8 - ELEC-
TRICAL/RESTRAINTS/FRONT CENTER SEAT BELT & RETRACTOR - REMOVAL).
DR/DH
RESTRAINTS - SERVICE INFORMATION
8O - 293
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст