Dodge Ram Truck 1500-2500-3500. Manual — part 1128
P2149-BANK 2 (CYLINDERS 4-6) SHORTED HIGH OR LOW (CONTINUED)
For the Engine circuit diagram (Refer to 9 - ENGINE - SCHEMATICS AND DIAGRAMS)
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
While the engine is running.
•
Set Condition:
A misfire detected at cylinders 4,5, or 6 or any combination of cylinders 4,5, or 6.
Possible Causes
OTHER DTC’S
HIGH SIDE DRIVER CIRCUIT OPEN
LOW SIDE DRIVER CIRCUIT OPEN
HIGH SIDE DRIVER SHORTED TO LOW SIDE DRIVER
HIGH SIDE DRIVERS SHORTED LOW
LOW SIDE DRIVER CIRCUIT SHORTED OTHER LOW SIDE DRIVER CIRCUIT
LOW SIDE DRIVERS SHORTED LOW
HIGH SIDE DRIVER SHORTED TO VOLTAGE
LOW SIDE DRIVER SHORTED TO VOLTAGE
LOW SIDE DRIVER CIRCUIT SHORTED IN INJECTOR HARNESS
INJECTOR
INJECTOR HARNESS
ECM
INTERMITTENT CONDITION
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING)
Diagnostic Test
1.
OTHER DTC’S
With the scan tool, read DTCs.
Do you have any combination of DTC’s P0204, P0205, or P0206?
Yes
>> Repair other DTC’s first.
Perform POWERTRAIN VERIFICATION TEST VER - 1 (DIESEL). (Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/ENGINE CONTROL MODULE - DIAGNOSIS AND TESTING)
No
>> Go To 2
9 - 1434
ENGINE - ELECTRICAL DIAGNOSTICS - DIESEL
DR/DH
P2149-BANK 2 (CYLINDERS 4-6) SHORTED HIGH OR LOW (CONTINUED)
2.
HIGH SIDE DRIVER CIRCUIT OPEN
Turn the ignition off.
Disconnect the ECM harness connectors.
Disconnect the Injector 4-6 harness connector.
NOTE: Check connectors - Clean/repair as necessary.
Measure the resistance of the injector high side driver circuit between
the Bank 2 high side driver circuit in the ECM harness connector and
the high side driver circuit in the injector harness connectors for cylin-
ders 4-6.
Is the resistance less than 10 Ohms?
Yes
>> Go To 3
No
>> Repair the open high side driver circuit from ECM harness
connector to the Injector harness connector.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)
3.
LOW SIDE DRIVER CIRCUIT OPEN
Measure the resistance of the #4,#5, and #6 injector low side driver
circuits between the ECM harness connector and the injector harness
connectors.
Is the resistance less than 10 Ohms?
Yes
>> Go To 4
No
>> Repair the open low side driver circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)
DR/DH
ENGINE - ELECTRICAL DIAGNOSTICS - DIESEL
9 - 1435
P2149-BANK 2 (CYLINDERS 4-6) SHORTED HIGH OR LOW (CONTINUED)
4.
HIGH SIDE DRIVER SHORTED TO LOW SIDE DRIVER
Measure the resistance between the Bank 2 high side driver circuit at
the ECM harness connector and the low side driver circuit for injectors
4-6 at the ECM harness connector.
Is the resistance more than 100k Ohms?
Yes
>> Go To 5
No
>> Repair the High side circuit shorted to the low side circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)
5.
HIGH SIDE DRIVERS SHORTED LOW
Measure the resistance of the injector harness connector high side
driver circuits to battery negative for injectors 4-6.
Is the resistance more than 100k Ohms?
Yes
>> Go To 6
No
>> Repair the High side driver shorted low in the harness.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)
9 - 1436
ENGINE - ELECTRICAL DIAGNOSTICS - DIESEL
DR/DH
P2149-BANK 2 (CYLINDERS 4-6) SHORTED HIGH OR LOW (CONTINUED)
6.
LOW SIDE DRIVERS SHORTED LOW
Measure the resistance of the injector harness connector Low side
driver circuits to battery negative for injectors 4-6.
Is the resistance more than 100k Ohms?
Yes
>> Go To 7
No
>> Repair the Low side driver shorted low in the harness.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)
7.
HIGH SIDE DRIVER SHORTED TO VOLTAGE
Turn Ingition on, engine off.
Measure the voltage between the high side driver circuit in the engine
harness and battery negative.
Is the voltage less than 1 volt?
Yes
>> Go To 8
No
>> Repair the high side driver shorted to voltage.
Perform POWERTRAIN VERIFICATION TEST VER - 1
(DIESEL). (Refer to 8 - ELECTRICAL/ELECTRONIC CON-
TROL MODULES/ENGINE CONTROL MODULE - DIAG-
NOSIS AND TESTING)
DR/DH
ENGINE - ELECTRICAL DIAGNOSTICS - DIESEL
9 - 1437
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст