Dodge Ram Truck 1500-2500-3500. Manual — part 2033
ZONE OVERCURRENT (DUAL-ZONE) (CONTINUED)
6.
CHECK THE (C34) COMMON DOOR DRIVER CIRCUIT FOR A SHORT TO THE (C32) RECIRCULATION
DOOR DRIVER CIRCUIT, THE (C61) BLEND DOOR DRIVER CIRCUIT, THE (C801) MODE DOOR 1 DRIVER
CIRCUIT, THE (C29) MODE DOOR 2 DRIVER CIRCUIT, & THE (C33) PASSENGER BLEND DOOR DRIVER
CIRCUIT
Measure the resistance between the (C34) Common Door Driver Cir-
cuit and the (C32) Recirculation Door Driver circuit, the (C61) Blend
Door Driver circuit, the (C801) Mode Door 1 Driver circuit, the (C29)
Mode Door 2 Driver circuit, and, the (C33) Passenger Blend Door
Driver circuit in the A/C Heater Control C1 harness connector.
Is the resistance below 30.0 ohms on any of the circuits?
Yes
>> Go To 7
No
>> Go To 8
7.
CHECK THE DOOR DRIVER CIRCUITS WHOSE RESISTANCE WAS BELOW 30.0 OHMS IN THE
PREVIOUS STEP FOR A SHORT TO THE (C34) COMMON DOOR DRIVER CIRCUIT
Disconnect all door actuator harness connectors whose circuit resis-
tance was below 30.0 ohms.
Measure the resistance between the (C34) Common Door Driver cir-
cuit and each applicable door driver circuit in the A/C Heater Control
C1 harness connector.
Is the resistance below 10k ohms on any of the circuits?
Yes
>> Repair the door driver circuits with a resistance below 10k
ohms for a short to the (C34) Common Door Driver circuit.
Perform BODY VERIFICATION TEST - VER 1. (Refer to 8
-
ELECTRICAL/ELECTRONIC
CONTROL
MODULES/
FRONT CONTROL MODULE - DIAGNOSIS AND TEST-
ING).
No
>> Replace all door actuators with a resistance below 30.0
ohms in accordance with the Service Information.
Perform BODY VERIFICATION TEST - VER 1. (Refer to 8
-
ELECTRICAL/ELECTRONIC
CONTROL
MODULES/
FRONT
CONTROL
MODULE
-
DIAGNOSIS
AND
TESTING).
24 - 132
HVAC - ELECTRICAL DIAGNOSTICS
DR/DH
ZONE OVERCURRENT (DUAL-ZONE) (CONTINUED)
8.
RUN THE ACTUATOR CIRCUIT TEST
Reconnect the A/C Heater Control C1 harness connector.
Turn the ignition on.
With the DRBIII
T
in HVAC, select System Tests and then select Actuator Circuit Test. Allow the test to run to com-
pletion before proceeding.
Does the DRBIII
T
display any Actuator Circuit Test fault messages?
Yes
>> Diagnose and repair the fault(s). Refer to *ACTUATOR CIRCUIT TEST DIAGNOSTICS (DUAL-ZONE) in
this section.
No
>> Replace the A/C Heater Control in accordance with the Service Information.
Perform BODY VERIFICATION TEST - VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES/FRONT CONTROL MODULE - DIAGNOSIS AND TESTING).
DR/DH
HVAC - ELECTRICAL DIAGNOSTICS
24 - 133
*A/C HEATER CONTROL ILLUMINATION INOPERATIVE
24 - 134
HVAC - ELECTRICAL DIAGNOSTICS
DR/DH
*A/C HEATER CONTROL ILLUMINATION INOPERATIVE (CONTINUED)
For the Manual Temperature Control circuit diagrams (Refer to 24 - HEATING & AIR CONDITIONING - SCHEMAT-
ICS AND DIAGRAMS).
For a complete wiring diagram Refer to Section 8W.
Possible Causes
FAULTS PRESENT IN THE CLUSTER (MIC)
(E16) PANEL LAMPS DRIVER CIRCUIT OPEN
BULB(S) - FILAMENT OPEN (SINGLE-ZONE HVAC MODULE ONLY)
CLUSTER (MIC)
A/C HEATER CONTROL
Diagnostic Test
1.
CHECK FOR DTCs IN THE CLUSTER (MIC)
Turn the ignition on.
With the DRBIII
T
, read Cluster DTCs.
Does the DRBIII
T
display any DTCs?
Yes
>> Diagnose and repair the DTC(s). (Refer to 8 - ELECTRICAL/INSTRUMENT CLUSTER - DIAGNOSIS
AND TESTING) for the diagnostic test procedure.
Perform BODY VERIFICATION TEST - VER 1. (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES/FRONT CONTROL MODULE - DIAGNOSIS AND TESTING).
No
>> Go To 2
2.
TEST (E16) PANEL LAMPS DRIVER CIRCUIT USING A TEST LIGHT
Turn the Headlamp switch on.
Rotate the Cargo Dome switch to the full brightness setting.
CAUTION: The test light must illuminate brightly. Compare the
brightness to that of a direct connection to the battery.
Using a 12-volt test light connected to ground, back probe the (E16)
Panel Lamps Driver circuit in the A/C Heater Control C1 harness con-
nector.
Does the test light illuminate brightly?
Yes (Dual-Zone Systems)
Replace the A/C Heater Control in accordance with the
Service Information.
Perform BODY VERIFICATION TEST - VER 1. (Refer to 8
-
ELECTRICAL/ELECTRONIC
CONTROL
MODULES/
FRONT CONTROL MODULE - DIAGNOSIS AND TEST-
ING).
Yes (Single-Zone Systems)
Go To 3
No
>> Go To 4
DR/DH
HVAC - ELECTRICAL DIAGNOSTICS
24 - 135
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст