Dodge Ram Truck 1500-2500-3500. Manual — part 1962
SEAT BACK REAR - FOOTMANS LOOP BRACKETS
REMOVAL
1. Remove the rear seat (Refer to 23 - BODY/SEATS/
SEAT - REAR - REMOVAL).
2. Remove bolts (2) and remove the loop (1).
INSTALLATION
1. Install the loop (1) and install the bolts (2).
2. Tighten the bolts (2) to 12 N·m (9 ft. lbs.).
3. Install the seat (Refer to 23 - BODY/SEATS/SEAT -
REAR - INSTALLATION).
23 - 202
SEATS
DR/DH
STATIONARY GLASS
TABLE OF CONTENTS
page
page
BACKLITE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 203
. . . . . . . . . . . . . . . . . . . . . . . . 204
BACKLITE VENT GLASS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
. . . . . . . . . . . . . . . . . . . . . . . . 206
WINDSHIELD
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
. . . . . . . . . . . . . . . . . . . . . . . . 209
BACKLITE
REMOVAL
CAUTION: It is difficult to salvage the backlite dur-
ing the removal operation. The backlite is part of
the structural support for the roof. The urethane
bonding used to secure the glass to the fence is
difficult to cut or clean from any surface. Since the
molding is set in urethane, it is unlikely it would
be salvaged. Before removing the backlite, check
the availability from the parts supplier.
NOTE: The backlite is attached to the window
frame with urethane adhesive. The urethane adhe-
sive is applied cold and seals the surface area
between the window opening and the glass. The
primer adheres the urethane adhesive to the back-
lite.
1. Roll down door glass.
2. Remove headliner (9) (Refer to 23 - BODY/INTE-
RIOR/HEADLINER - REMOVAL).
3. On standard cab models remove the upper b-pillar
trim (5) (Refer to 23 - BODY/INTERIOR/B-PILLAR
UPPER TRIM - REMOVAL).
DR/DH
STATIONARY GLASS
23 - 203
4. On quad cab models remove the upper c-pillar trim
(5) (Refer to 23 - BODY/INTERIOR/C-PILLAR
UPPER TRIM - REMOVAL).
5. Bend backlite retaining tab (2) inward against
glass.
6. Disconnect the rear window defogger electrical
connector (if equipped).
7. Using a suitable pneumatic knife from inside the
vehicle, cut urethane holding backlite frame to
opening fence.
8. Separate glass (1) from vehicle.
INSTALLATION
1. Clean urethane adhesive from around backlite
opening fence.
2. If necessary, apply black-out primer to outer edge
of replacement backlite frame (1).
3. If black-out primer was pre-applied on backlite,
clean bonding surface with Isopropyl alcohol and
clean lint free cloth. Allow 3 minutes for drying
time.
4. Apply black-out primer to backlite opening fence.
5. Apply a 13 mm (0.5 in.) bead of urethane (4)
around the perimeter of the window frame bonding
surface (1).
23 - 204
STATIONARY GLASS
DR/DH
6. Set glass (1) on lower fence and move glass for-
ward into opening.
7. Firmly push glass (1) against rear window glass
opening fence.
8. Bend tabs around edges of backlite opening fence
to retain glass.
9. Clean excess urethane from exterior with MOPAR
T
,
Super Clean or equivalent.
10. Allow urethane to cure at least 24 hours (full cure
is 72 hours).
11. Water test to verify repair before returning vehicle
to service.
12. Connect the rear window defogger electrical con-
nector, if equipped.
13. On standard cab models, install the upper b-pillar
trim (5) (Refer to 23 - BODY/INTERIOR/B-PILLAR
UPPER TRIM - INSTALLATION).
14. On quad cab models, install the upper c-pillar trim
(5) (Refer to 23 - BODY/INTERIOR/C-PILLAR
UPPER TRIM - INSTALLATION).
DR/DH
STATIONARY GLASS
23 - 205
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст