Dodge Sprinter. Manual — part 393
TEST
ACTION
APPLICABILITY
4
Turn the ignition off.
NOTE: Check connectors - Clean/repair as necessary.
Disconnect the Automatic Temperature Control (ATC) C1 harness connector.
Disconnect the A/C Compressor Clutch harness connector.
Measure the resistance of the A/C Compressor Clutch Control circuit between the
Automatic Temperature Control (ATC) C1 harness connector and the A/C Compres-
sor Clutch harness connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Replace the Automatic Temperature Control (ATC) in accordance
with the Service Information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Repair the A/C Compressor Clutch Control circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
129
HEATING & A/C
A/C COMPRESSOR CONTROL HIGH OR OPEN (ACTIVE) —
Continued
Symptom List:
A/C COMPRESSOR CONTROL HIGH OR OPEN (STORED)
A/C COMPRESSOR CONTROL SHORTED LOW (STORED)
AIR OUTLET TEMP SENSOR HIGH OR OPEN (STORED)
AIR OUTLET TEMP SENSOR SHORTED LOW (STORED)
AUX FAN RELAY CONTROL HIGH OR OPEN (STORED)
AUX FAN RELAY CONTROL SHORTED LOW (STORED)
BLOWER STAGE 1 HIGH OR OPEN (STORED)
BLOWER STAGE 1 SHORTED LOW (STORED)
CABIN HEATER CONTROL HIGH OR OPEN (STORED)
CABIN HEATER CONTROL SHORTED LOW (STORED)
CIRC PUMP CONTROL HIGH OR OPEN (STORED)
CIRC PUMP CONTROL SHORTED LOW (STORED)
EVAP TEMP SENSOR HIGH OR OPEN (STORED)
EVAP TEMP SENSOR SHORTED LOW (STORED)
NO COMMUNICATION BUS (STORED)
NO COMMUNICATION WITH ECM (STORED)
NO COMMUNICATION WITH IC (STORED)
RECIRC AIR SOLENOID CONTROL HIGH OR OPEN (STORED)
RECIRC AIR SOLENOID CONTROL SHORTED LOW (STORED)
REFRIG PRESS SENSOR HIGH OR OPEN (STORED)
REFRIG PRESS SENSOR SHORTED LOW (STORED)
WATER CYCLE VALVE CONTROL HIGH OR OPEN (STORED)
WATER CYCLE VALVE CONTROL SHORTED LOW (STORED)
Test Note:
All symptoms listed above are diagnosed using the same tests.
The title for the tests will be A/C COMPRESSOR CONTROL
HIGH OR OPEN (STORED).
When Monitored and Set Condition:
NO COMMUNICATION BUS (STORED)
When Monitored:
With the ignition on.
Set Condition:
This DTC will set if the Automatic Temperature Control (ATC) fails to
receive all module messages.
NO COMMUNICATION WITH ECM (STORED)
When Monitored:
With the ignition on.
Set Condition:
This DTC will set if the Automatic Temperature Control (ATC) fails to
receive all messages from the ECM.
130
HEATING & A/C
NO COMMUNICATION WITH IC (STORED)
When Monitored:
With the ignition on.
Set Condition:
This DTC will set if the Automatic Temperature Control (ATC) fails to
receive all messages from the Instrument Cluster.
POSSIBLE CAUSES
CHECK FOR ACTIVE AUTOMATIC TEMPERATURE CONTROL (ATC) DTCS
INTERMITTENT CONDITION
TEST
ACTION
APPLICABILITY
1
NOTE: All of the following criteria must be met in order to successfully run
the ATC Function Test.
Place the shift lever in Park.
Turn the ignition on.
With the DRBIII
t, record and erase ATC DTC’s.
Start the engine. Allow the engine to reach normal operating temperature.
Set the blower to high speed.
Press the Air Conditioning switch On.
With the DRBIII
t, verify that the ambient temperature is above 59°F (15°C), the
refrigerant pressure is between 29 and 348 PSI (2 and 24 bar), the evaporator
temperature is above 36.5°F (2.5°C), and the coolant temperature is above 158°F
(70°C).
With the DRBIII
t in Automatic Temperature Control (ATC), select System Tests and
select ATC Function Test. When the ATC Function Test is complete, proceed as
follows:
With the DRBIII
t, read the active ATC DTCs.
Does the DRBIII
t display any DTCs?
All
Yes
→ Return to the Heating & A/C Symptom List and choose the
symptom(s).
Perform BODY VERIFICATION TEST - VER 1.
No
→ Using the wiring diagram/schematic as a guide, inspect the
wiring and connectors related to the circuit(s) that caused the
original DTC(s) to set.
Perform BODY VERIFICATION TEST - VER 1.
131
HEATING & A/C
A/C COMPRESSOR CONTROL HIGH OR OPEN (STORED) —
Continued
Symptom:
A/C COMPRESSOR CONTROL SHORTED LOW (ACTIVE)
POSSIBLE CAUSES
A/C COMPRESSOR CLUTCH
A/C COMPRESSOR CLUTCH CONTROL CIRCUIT SHORTED TO GROUND
A/C COMPRESSOR CLUTCH CONTROL CIRCUIT SHORTED TO GROUND CIRCUIT
A/C COMPRESSOR CLUTCH CONTROL CIRCUIT SHORTED TO SENSOR GROUND CIRCUIT
AUTOMATIC TEMPERATURE CONTROL (ATC)
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
Press the Air Conditioning switch off.
Turn the ignition off.
Disconnect the A/C Compressor Clutch harness connector.
Turn the ignition on.
With the DRBIII
t, record and erase Automatic Temperature Control DTCs.
Turn the ignition off, wait 5 seconds, then turn the ignition on.
With the DRBIII
t, read the Automatic Temperature Control DTCs.
Does the DRBIII
t display: A/C COMPRESSOR CONTROL HIGH OR OPEN?
All
Yes
→ Replace the A/C Compressor Clutch in accordance with the
Service Information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 2
2
Turn the ignition off.
Disconnect the A/C Compressor Clutch harness connector.
Disconnect the Automatic Temperature Control (ATC) C1 harness connector.
Measure the resistance between ground and the A/C Compressor Clutch Control
circuit.
Is the resistance below 10k ohms?
All
Yes
→ Repair the A/C Compressor Clutch Control circuit for a short to
ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 3
3
Turn the ignition off.
Disconnect the A/C Compressor Clutch harness connector.
Disconnect the Automatic Temperature Control (ATC) C1 harness connector.
Measure the resistance between the A/C Compressor Clutch Control circuit and the
Ground circuit in the Automatic Temperature Control C1 harness connector.
Is the resistance below 10k ohms?
All
Yes
→ Repair the A/C Compressor Clutch Control circuit for a short to
the Ground circuit.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 4
132
HEATING & A/C
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст