Lincoln Nautilus (2022 year). Manual in english — page 5

WARNING: Do not set MyKey

maximum speed limit to a limit that will
prevent the driver from maintaining a safe
speed considering posted speed limits and
prevailing road conditions. The driver is
always responsible to drive in accordance
with local laws and prevailing conditions.
Failure to do so could result in accident or
injury.

•

A vehicle speed limit can be set.
Warnings will be shown in the display
followed by an audible tone when your
vehicle reaches the set speed. You
cannot override the set speed by fully
depressing the accelerator pedal or by
setting cruise control.

•

Various vehicle speed minders can be
set. Once you select a speed, it will be
shown in the display, followed by an
audible tone when the preselected
vehicle speed is exceeded.

•

Audio system maximum volume of 45%.
A message will be shown in the display
when you attempt to exceed the limited
volume. Also, the speed-sensitive or
compensated automatic volume control
will be disabled.

•

Always on setting. When this is selected,
you will not be able to switch off
AdvanceTrac™ or traction control, 911
Assist or Emergency Assistance, or the
do not disturb feature, if your vehicle
comes with these features.

CREATING A MYKEY

Use the information display to create a
MyKey:

E203693

86

MyKey™

E203694

1. Insert the key you want to program into

the ignition. If your vehicle has a
push-button start, place the remote
control in the backup slot.

2. Switch the ignition on.

3. Access the main menu in the information

display and then scroll through the
menus to change the settings of your
MyKey. From the MyKey menu select the
option Create MyKey. See Instrument
Cluster Display (page 145).

4. When prompted, hold the OK button until

you see a message informing you to label
this key as a MyKey. The programmed
restrictions apply when you switch the
vehicle off, open and close the driver
door and restart your vehicle with the
programmed key or remote control.

5. Switch the ignition off.

You successfully created a MyKey. Make
sure you label it so you can distinguish it
from the admin keys.

You can also program configurable settings
for the keys.

Programming and Changing
Configurable Settings

Use the information display to access your
configurable MyKey settings.

1. Switch the ignition on using an admin key

or remote control you want to program.

2. Access the main menu in the information

display and then scroll through the
menus to change the settings of the
MyKey. See Instrument Cluster Display
(page 145).

3. Follow the instructions in the display. The

programmed restrictions apply when you
switch the vehicle off, open and close the
driver door and restart your vehicle with
the programmed key or remote control.

Note: You can clear or change your MyKey
settings at any time during the same key
cycle as you created the MyKey. Once you
have switched the vehicle off, however, you
need an admin key to change or clear your
MyKey settings. When you make any
changes to your MyKey settings, you change
the settings for every MyKey. You cannot
make individual changes to apply to certain
MyKeys.

CLEARING ALL MYKEYS

When you clear your MyKeys, you remove
all restrictions and return all MyKeys to their
original admin key status at once. To clear
all MyKeys of all MyKey settings, use the
information display.

1. Switch the ignition on using an admin

key.

87

MyKey™

2. Access the main menu in the information

display and then scroll through the
menus to begin clearing your MyKey
programming.

3. Follow the instructions in the display.

4. A confirmation message appears in the

display after you finish clearing your
MyKeys.

Note: When you clear your MyKeys, you
remove all restrictions and return all MyKeys
to their original admin key status. You cannot
remove the MyKey restrictions individually.

CHECKING MYKEY SYSTEM
STATUS

You can find information about your
programmed MyKeys by using the
information display.

MyKey Distance

Tracks the distance when drivers use a
MyKey. The only way to delete the
accumulated distance is by using an admin
key to clear all MyKeys. If the distance does
not accumulate as expected, then the
intended user is not using the MyKey, or an
admin key user recently cleared and then
recreated a MyKey.

Number of MyKeys

Indicates the number of MyKeys
programmed to your vehicle. Use this feature
to detect how many MyKeys you have for
your vehicle and determine when all MyKeys
have been deleted.

Number of Admin Keys

Indicates how many admin keys are
programmed to your vehicle. Use this feature
to determine how many admin keys you have
for your vehicle, and detect if an additional
MyKey has been programmed.

USING MYKEY WITH REMOTE
START SYSTEMS

MyKey is not compatible with non
Lincoln-approved, aftermarket remote start
systems. If you choose to install a remote
start system, see an authorized dealer for a
Lincoln-approved remote start system.

MYKEY – TROUBLESHOOTING

Potential Causes

Condition

The key or transmitter used to start the vehicle does not have admin privileges.

I cannot create a MyKey.

88

MyKey™

Potential Causes

Condition

Vehicles with keyless start: Make sure you place the transmitter into the backup slot. See What Is
the Passive Anti-Theft System (page 110).
The key or transmitter used to start the vehicle is the only admin key. There always has to be at
least one admin key.
The passive anti-theft system is disabled or in unlimited mode.

The transmitter used to start your vehicle does not have admin privileges.

I cannot program the configurable
settings.

There are no MyKeys programmed to the vehicle. See Creating a MyKey (page 86).

The key or transmitter used to start the vehicle does not have admin privileges.

I cannot clear the MyKeys.

No MyKeys are created. See Creating a MyKey (page 86).

Purchase a new key or transmitter from an authorized dealer.

I lost the only admin key.

Program a spare key or transmitter. You may need to see an authorized dealer. See What Is the
Passive Anti-Theft System (page 110).

I lost a key.

The MyKey user is not using the MyKey.

The MyKey distance does not accumu-
late.

An admin key holder cleared the MyKeys and created new MyKeys.
The key system has been reset.

An admin transmitter is present at vehicle start.

No MyKey functions with the trans-
mitter.

There are no MyKeys programmed to your vehicle. See Creating a MyKey (page 86).

89

MyKey™

OPERATING THE DOORS FROM
OUTSIDE YOUR VEHICLE

UNLOCKING AND LOCKING THE
DOORS USING THE REMOTE
CONTROL

You can only use the remote control when
your vehicle is stationary.

Unlocking the Doors

E267112

Press the button to unlock all
doors.

Locking the Doors

E267111

Press the button to lock all doors.
One short flash of the turn signal
lamps confirms that your vehicle

has locked.

UNLOCKING AND LOCKING THE
DOORS USING THE KEY BLADE

If there is a power door lock fault you can
use the key blade to lock and unlock the
doors.

E151956

If the central locking function does not
operate, lock the doors individually using the
key in the position shown.

Left-Hand Side

Turn clockwise to lock.

Right-Hand Side

Turn counterclockwise to lock.

Unlocking the Doors

If the central locking function does not
operate, unlock the driver door and then
unlock all other doors individually by pulling
the interior door handles.

Note: When the doors have been unlocked
using this method, the doors must be locked
individually until the central locking function
has been repaired.

INDIVIDUALLY UNLOCKING AND
LOCKING THE DOORS USING THE KEY
BLADE

If there is a power door lock fault you can
use the key blade to lock and unlock the
doors.

90

Doors and Locks

E112203

Lock.

A

Unlock.

B

OPERATING THE DOORS FROM
INSIDE YOUR VEHICLE

INDIVIDUALLY UNLOCKING AND
LOCKING THE DOORS USING THE
LOCKING BUTTON

The power door lock control is on the driver
and front passenger door panels.

E138628

Unlock.

A

Lock.

B

OPENING THE DOORS FROM INSIDE
YOUR VEHICLE

Pull the interior door handle twice to unlock
and open a rear door. The first pull unlocks
the door and the second pull opens the door.

AUTOUNLOCK

WHAT IS AUTOUNLOCK

Autounlock is an unlocking feature that
unlocks the vehicle doors when your vehicle
comes to a stop.

AUTOUNLOCK REQUIREMENTS

Autounlock unlocks all the doors when all of
the following occur:
•

The ignition is on, all the doors are closed
and your vehicle is moving at a speed
greater than 12 mph (20 km/h).

•

Your vehicle comes to a stop.

•

You open the driver door within 10
minutes of switching the ignition off or to
the accessory position.

91

Doors and Locks

SWITCHING AUTOUNLOCK ON AND
OFF

1. Press the menu button on the steering

wheel to enter the information display
main menu.

2. Select Settings.

3. Select Vehicle.

4. Select Locks.

5. Switch Autounlock on or off.

AUTOLOCK

WHAT IS AUTOLOCK

Autolock is a locking feature that locks your
vehicle doors when you start driving.

AUTOLOCK REQUIREMENTS

Autolock locks all the doors when all of the
following occur:
•

All doors are closed.

•

The ignition is on.

•

Your vehicle reaches a speed greater
than 12 mph (20 km/h).

MISLOCK

WHAT IS MISLOCK

Mislock is a locking feature that warns you
if your vehicle has not locked.

MISLOCK LIMITATIONS

When you press the lock button once, the
direction indicators do not flash if any door
or the liftgate or hood is open.

1. If any door or the liftgate is open.

2. The hood is open.

SWITCHING MISLOCK ON AND OFF

1. Press the menu button on the steering

wheel to enter the information display
main menu.

2. Select Settings.
3. Select Vehicle.

4. Select Locks.

5. Switch Mislock Chirp on or off.

DOORS AND LOCKS AUDIBLE
WARNINGS

Door Ajar Audible Warning

Sounds when a door is not fully closed and
your vehicle is moving.

92

Doors and Locks

DOORS AND LOCKS –
TROUBLESHOOTING

DOORS AND LOCKS – WARNING
LAMPS

Door Ajar Warning Lamp

E249859

It illuminates when you switch the
ignition on and remains on if any
door or the hood is open.

DOORS AND LOCKS – INFORMATION MESSAGES

Action

Message

Displays if a door is open. Fully close the door.

Driver Door Ajar

Passenger Door Ajar

Rear Left Door Ajar

Rear Right Door Ajar

93

Doors and Locks

LOCATING THE KEYLESS ENTRY
KEYPAD

The keypad is near the driver window and
illuminates when you touch it.

E190936

KEYLESS ENTRY LIMITATIONS

Make sure your remote control is within 3 ft
(1 m) from the front door handles and the
tailgate.

The system could not function if:
•

The remote control remains stationary
for about a minute.

•

The vehicle battery has no charge.

•

The remote control battery has no
charge.

•

There is interference causing issues with
the remote control frequencies.

•

The remote control is too close to metal
objects or electronic devices, for example
keys or a cell phone.

KEYLESS ENTRY SETTINGS

Switching Keyless Entry On and Off

1. Switch the ignition on using an original

key that has not been created as a
MyKey.

2. Press Settings on the touchscreen.

3. Press Vehicle Settings.

4. Press Locks.

Reprogramming the Unlocking
Function

You can enable two-stage unlocking function
allowing you to unlock only the driver door
when you touch the unlock sensor.

Press and hold both the lock and unlock
buttons on the remote control for four
seconds to disable or enable two-stage
unlocking.

If you program the unlocking function so that
only the driver door unlocks, you can unlock
all of the other doors from inside your vehicle
using the power door lock control. You can
unlock individual doors by pulling the interior
door handles on those doors.

USING KEYLESS ENTRY

Unlocking the Doors

E248553

94

Keyless Entry

With the remote control within 3 ft (1 m) of
your vehicle, touch the unlock sensor on the
back of the door handle for a brief period
and then pull on the door handle to unlock,
being careful not to touch the lock sensor at
the same time or pull on the door handle too
quickly. The system requires a brief delay to
authenticate the remote control.

Locking the Doors

E248554

With your passive key within 3 ft (1 m) of your
vehicle, touch the outer door handle lock
sensor for approximately one second to lock,
being careful not to touch the unlock sensor
on the back of the door handle at the same
time. After locking, you can immediately pull
on the door handle to confirm locking
occurred without inadvertently unlocking.

Opening the Liftgate with the Remote
Control

E291416

Press the exterior liftgate release button
inside of the liftgate handle. The liftgate
unlocks and opens. See Opening the
Liftgate From Outside Your Vehicle (page
102).

LOCKING AND UNLOCKING THE
DOORS USING KEYLESS ENTRY

UNLOCKING THE DOORS

E248553

With the remote control within 3 ft (1 m) of
your vehicle, touch the unlock sensor on the
back of the door handle for a brief period
and then pull on the door handle to unlock,
being careful not to touch the lock sensor at
the same time or pull on the door handle too
quickly. The system requires a brief delay to
authenticate the remote control.

95

Keyless Entry

Opening the Liftgate with the Remote
Control

E291416

Press the exterior liftgate release button
inside of the liftgate handle. The liftgate
unlocks and opens. See Opening the
Liftgate From Outside Your Vehicle (page
102).

KEYLESS ENTRY –
TROUBLESHOOTING

KEYLESS ENTRY – FREQUENTLY
ASKED QUESTIONS

Why does the keypad not accept the access
code?

If you enter the access code too fast on
the keypad, the unlock function may not
work. Slowly re-enter the access code.

Why does the passive key not work?

The system deactivates passive keys
left inside your vehicle when you lock
it. You cannot switch the ignition on
using a deactivated passive key. Press
the unlock button on the remote control
to reactivate a passive key.

Why does the keypad not function?

The keypad goes into an anti-scan
mode if you enter a wrong code seven
times. The anti-scan mode disables the
keypad for one minute and the red light
flashes.

96

Keyless Entry

WHAT IS THE KEYLESS ENTRY
KEYPAD

The keyless entry keypad allows you to lock
and unlock your vehicle using the keypad
on the window trim.

KEYLESS ENTRY KEYPAD
LIMITATIONS

The system may not function if:
•

The vehicle battery has no charge.

LOCATING THE KEYLESS ENTRY
KEYPAD

The keypad is near the driver window and
illuminates when you touch it.

E190936

KEYLESS ENTRY KEYPAD MASTER
ACCESS CODE

Unlocking the Doors

E138637

Enter the factory-set five-digit code or your
personal code. You must press each number
within five seconds of each other.

•

Press 3-4 within five seconds to unlock
all doors.

97

Keyless Entry Keypad

Locking the Doors

E138637

Press and hold 7·8 and 9·0 at the same time
with the driver door closed.

Note: You do not need to enter the code
first.

KEYLESS ENTRY KEYPAD
PERSONAL ACCESS CODES

Programming a Personal Entry Code

1. Enter the five-digit master code.
2. Press 1·2 on the keypad within five

seconds.

3. Enter your personal five-digit code. You

must do this within five seconds of
completing Step 2.

4. Press 1·2 on the keypad to save personal

code 1.

The doors lock then unlock to confirm that
programming was successful.

To program additional personal entry codes,
repeat Steps 1 through 3, then for Step 4:
•

Press 3·4 to save personal code 2.

•

Press 5·6 to save personal code 3.

•

Press 7·8 to save personal code 4.

•

Press 9·0 to save personal code 5.

If your vehicle comes with SYNC, you can
also program the system with a personal
entry code.

Hints:
•

Do not set a code that uses five of the
same number.

•

Do not use five numbers in sequential
order.

•

The five-digit master code works even if
you have set your own personal code.

Erasing a Personal Code

1. Enter the five-digit master code.

2. Press and release 1·2 on the keypad

within five seconds.

3. Press and hold 1·2 for two seconds. You

must do this within five seconds of
completing Step 2.

All personal codes erase and only the
five-digit master code works.

Anti-Scan Feature

The keypad goes into an anti-scan mode if
you enter the wrong code seven times. This
mode turns off the keypad for one minute
and the keypad lamp flashes.

98

Keyless Entry Keypad

The anti-scan feature turns off after:
•

One minute of keypad inactivity.

•

You press the unlock button on the
remote control.

•

You switch the ignition on.

•

You unlock your vehicle using keyless
entry.

USING THE KEYLESS ENTRY
KEYPAD

Unlocking the Doors

E138637

Enter the factory-set five-digit code or your
personal code. You must press each number
within five seconds of each other.

•

Press 3-4 within five seconds to unlock
all doors.

Locking the Doors

E138637

Press and hold 7·8 and 9·0 at the same time
with the driver door closed.

Note: You do not need to enter the code
first.

99

Keyless Entry Keypad

KEYLESS ENTRY KEYPAD –
TROUBLESHOOTING

KEYLESS ENTRY KEYPAD –
FREQUENTLY ASKED QUESTIONS

Why does the keypad not accept the access
code?

If you enter the access code too fast on
the keypad, the unlock function may not
work. Slowly re-enter the access code.

Why does the keypad not function?

The keypad goes into an anti-scan
mode if you enter a wrong code seven
times. The anti-scan mode disables the
keypad for one minute and the red light
flashes.

100

Keyless Entry Keypad

HOW DOES EASY ENTRY AND
EXIT WORK

Easy entry and exit moves the driver seat
rearward up to 2 in (5 cm) and the steering
column up when you switch the ignition off.
The driver seat and steering column return
to their previous positions when you switch
the ignition on.

Note: Depending on your vehicle, the column
may move up and in.

SWITCHING EASY ENTRY AND
EXIT ON AND OFF

1. Using the touchscreen, select Settings.

2. Select Vehicle.

3. Select Easy Entry/Exit.

If you press any adjustment or memory
button when in easy exit mode, the system
cancels the operation.

101

Easy Entry and Exit