Dodge Caliber. Manual — part 362
1. Turn the headlamps On and select the Low beams.
2. The vertical alignment screw (2) is located on the
top of the headlamp leveling motor (4).
3. The horizontal alignment screw (2) is located next
to and inboard of the headlamp leveling motor.
A properly aimed low beam headlamp will project a high intensity light pattern on the screen with the horizontal
cut-off line aligned with the tape line 100 mm (3.94 in.) below the headlamp centerline. The intersection of the hor-
izontal and 15 degree cut-off lines in the projected pattern should align to the intersection of the headlamp center-
line vertical tape line and the tape line 100 mm (3.94 in.) below the headlamp horizontal centerline. The high beams
on a vehicle with aero headlamps cannot be aligned. The high beam pattern should be correct when the low beams
are aligned properly.
SPECIFICATIONS
EXTERIOR LAMPS
CAUTION: Do not use bulbs that have a higher candle power than the bulb listed in the chart below. Dam-
age to lamp can result. Do not touch halogen bulbs with fingers or other oily surfaces. Bulb life will be
reduced.
PM
LAMPS/LIGHTING - EXTERIOR - SERVICE INFORMATION
8L - 81
BULB APPLICATION TABLE
LAMP
BULB
Back-Up Lamp
921 W16W
Front Fog Lamp
9145
Front Park/Turn Signal/Side Marker Lamp
3157AK
Headlamp Low Beam/High Beam
H13
License Lamp
W5W
Rear Tail/Stop Lamp
3157
Rear Turn Signal
3757AK
BULB APPLICATION TABLE - EXPORT
LAMP
BULB
Front Position Lamp
W5W
Headlamp Low Beam/High Beam
H4
Rear Fog Lamp
3157
8L - 82
LAMPS/LIGHTING - EXTERIOR - SERVICE INFORMATION
PM
CENTER HIGH MOUNTED STOP LAMP
REMOVAL
1. Disconnect and isolate the battery negative cable.
2. Remove the rear spoiler (Refer to 23 - BODY/LIFT-
GATE - SPOILER - REMOVAL)
3. With spoiler on bench, remove the two screws to
the CHMSL.
4. Remove CHMSL from spoiler.
INSTALLATION
1. Place CHMSL onto rear spoiler.
2. Install the two mounting screws to the CHMSL.
3. Install the rear spoiler (Refer to 23 - BODY/LIFT-
GATE - SPOILER - INSTALLATION).
4. Connect the battery negative cable.
PM
LAMPS/LIGHTING - EXTERIOR - SERVICE INFORMATION
8L - 83
DAYTIME RUNNING LAMPS
DESCRIPTION
Vehicles built for use in Canada, and also available as an option on vehicles for sale in the U.S., are equipped with
a Daytime Running Lamp (DRL) system. All the exterior lighting messages come from Steering Control Module
(SCM) or left multi-function switch on Local Interconnect Network (LIN) data bus and goes to the Cab Compartment
Node (CCN), then the CCN sends out a Controller Area Network (CAN) data bus message to the Totally Integrated
Power Module (TIPM) for each lighting function according to the request from left multi-function switch. Then the
TIPM will turn ON/OFF the requested output. The DRL function is controlled by TIPM. Daytime running lamps are
High beam lamps at lower intensity.
OPERATION
The Canadian cluster provides steady illumination of the front turn signal when the ignition switch is in the ON
position. The Daytime Running Lamp (DRL) function may be inhibited by activating the turn signals, the hazard
flashers, the headlamp switch, or park brake.
8L - 84
LAMPS/LIGHTING - EXTERIOR - SERVICE INFORMATION
PM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст