Dodge Caliber. Manual — part 424
3.
CHECK (R4) RIGHT CURTAIN SQUIB 1 LINE 1 CIRCUIT AND (R2) RIGHT CURTAIN SQUIB 1 LINE 2
CIRCUIT FOR A SHORT TO BATTERY
WARNING: To avoid personal injury or death, turn the ignition off,
disconnect the battery and wait two minutes before proceeding.
Disconnect the 8443 Load Tool and Jumper from the Right Side Curtain
Airbag connector.
Disconnect the ORC connectors.
NOTE: Check connectors - Clean and repair as necessary.
Connect the 8443 Load Tool ORC 8443-25 Adaptor to the ORC con-
nectors.
Measure the voltage of the (R4) Right Curtain Squib 1 Line 1 circuit
between the ORC 8443-25 Adaptor cavity 7 and ground.
Measure the voltage of the (R2) Right Curtain Squib 1 Line 2 circuit
between the ORC 8443-25 Adaptor cavity 8 and ground.
Is there any voltage present on either circuit?
Yes
>> Repair the Right Curtain Squib 1 circuits with voltage
present for a short to battery.
Perform AIRBAG SYSTEM VERIFICATION TEST - VER 1.
No
>>
WARNING: If the Occupant Restraint Controller (ORC) is dropped at any time, it must be replaced. Failure to
take the proper precautions can result in accidental airbag deployment and personal injury or death.
WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.
Replace the ORC in accordance with Service Information.
Perform AIRBAG SYSTEM VERIFICATION TEST - VER 1.
4.
CHECKING STORED OR INTERMITTENT CODES
NOTE: Diagnose and repair all active codes before diagnosing stored codes. Refer to the Table of Contents
in this Section for a complete list of airbag system diagnostic procedures.
With the scan tool, record and erase all Airbag System Module DTCs.
WARNING: To avoid personal injury or death, turn the ignition off, disconnect the battery and wait two min-
utes before proceeding.
Using the wiring diagram/schematic as a guide, inspect the related wiring and connectors for chafed, pierced,
pinched, and partially broken wires, and for broken, bent, pushed out, corroded, and contaminated terminals. Repair
as necessary.
Reconnect all disconnected components and harness connectors.
WARNING: To avoid personal injury or death, turn the ignition on, then reconnect the battery.
With the scan tool, monitor for active codes while performing the following:
•
Wiggle the wiring harness and connectors of the related airbag circuit.
•
Continue the test until either a code becomes active or the problem area is isolated.
In the previous steps you have attempted to recreate the conditions responsible for setting the DTC in question /
causing the intermittent condition.
Are any ACTIVE DTCs present?
Yes
>> Select the appropriate diagnostic procedure from the Table of Contents in this section.
No
>> No problem found at this time. Erase all codes before returning the vehicle to the customer.
PM
RESTRAINTS - ELECTRICAL DIAGNOSTICS
8O - 93
B1B22-RIGHT SIDE CURTAIN SQUIB 1 CIRCUIT OPEN
For a complete wiring diagram Refer to Section 8W.
8O - 94
RESTRAINTS - ELECTRICAL DIAGNOSTICS
PM
•
When Monitored:
With the ignition on.
•
Set Condition:
The Occupant Restraint Controller (ORC) monitors the resistance of the Right Curtain Squib 1 circuits. The
ORC will set this DTC if it detects an open or high resistance on the Right Curtain Squib 1 circuits.
Possible Causes
(R4) RIGHT CURTAIN SQUIB 1 LINE 1 CIRCUIT OPEN
(R2) RIGHT CURTAIN SQUIB 1 LINE 2 CIRCUIT OPEN
RIGHT SIDE CURTAIN AIRBAG
OCCUPANT RESTRAINT CONTROLLER (ORC)
Diagnostic Test
1.
DETERMINE ACTIVE OR STORED DTC
NOTE: Ensure that the battery is fully charged.
NOTE: The scan tool, SRS Airbag Load Tool MRL 8443, and DVOM are required to perform the following
test.
Turn the ignition on.
Select ACTIVE or STORED DTC:
ACTIVE DTC
Go To 2
STORED DTC
Go To 5
2.
CHECK FOR OPEN SQUIB CIRCUITS IN RIGHT SIDE CURTAIN AIRBAG
WARNING: To avoid personal injury or death, turn the ignition off,
disconnect the battery and wait two minutes before proceeding.
Disconnect the Right Side Curtain Airbag connector.
WARNING: To avoid personal injury or death, do not place an
intact uncoupled curtain airbag face down on a hard surface, the
airbag will propel into the air if accidentally deployed.
NOTE: Check connectors - Clean and repair as necessary.
Connect the 8443 Load Tool and 8443-8 Jumper to the Right Side Cur-
tain Airbag connector.
WARNING: To avoid personal injury or death, turn the ignition on,
then reconnect the battery.
With the scan tool, read the active ORC DTCs.
Does the scan tool display: B1B22 RIGHT SIDE CURTAIN
SQUIB 1 CIRCUIT OPEN?
Yes
>> Go to 3
No
>> Replace the Right Side Curtain Airbag in accordance with
the Service Information.
Perform AIRBAG SYSTEM VERIFICATION TEST - VER 1.
PM
RESTRAINTS - ELECTRICAL DIAGNOSTICS
8O - 95
3.
CHECK (R4) RIGHT CURTAIN SQUIB 1 LINE 1 CIRCUIT FOR AN OPEN
WARNING: To avoid personal injury or death, turn the ignition off,
disconnect the battery and wait two minutes before proceeding.
Disconnect the 8443 Load Tool and Jumper from the Right Side Curtain
Airbag connector.
Disconnect the ORC connectors.
NOTE: Check connectors - Clean and repair as necessary.
Connect the 8443 Load Tool ORC Adaptor to the ORC C1 connector.
Measure the resistance of the (R4) Right Curtain Squib 1 Line 1 circuit
between the Right Side Curtain Airbag connector cavity 1 and the 8443
ORC 8443-25 Adaptor cavity 32-7.
Is the resistance below 1.0 ohm?
Yes
>> Go To 4
No
>> Repair the (R4) Right Curtain Squib 1 Line 1 circuit for an
open. Perform AIRBAG SYSTEM VERIFICATION TEST -
VER 1.
4.
CHECK (R2) RIGHT CURTAIN SQUIB 1 LINE 2 CIRCUIT FOR AN OPEN
Measure the resistance of the (R2) Right Curtain Squib 1 Line 2 circuit
between the Right Side Curtain Airbag connector cavity 2 and the ORC
8443-25 Adaptor cavity 8.
Is the resistance below 1.0 ohm?
Yes
>>
WARNING: If the Occupant Restraint Controller (ORC) is dropped
at any time, it must be replaced. Failure to take the proper precau-
tions can result in accidental airbag deployment and personal
injury or death.
WARNING: To avoid personal injury or death, turn the ignition off,
disconnect the battery and wait two minutes before proceeding.
Replace the ORC in accordance with Service Information.
Perform AIRBAG SYSTEM VERIFICATION TEST - VER 1.
No
>> Repair the (R2) Right Curtain Squib 1 Line 2 circuit for an
open.
Perform AIRBAG SYSTEM VERIFICATION TEST - VER 1.
8O - 96
RESTRAINTS - ELECTRICAL DIAGNOSTICS
PM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст